Why trimmers run out of line fast

Rating of trimmer lines producers

The quality of any type of line depends on the conscientiousness of the consumable manufacturers. According to numerous reviews, the cord of the following brands deserves special attention:

Why Your Trimmer Line Keeps Breaking (Solution) / Jon’s DIY

Brand name Product advantages Product disadvantages
“Oregon Excellent quality nylon monofilaments that do not sinter or lose their working properties when the coil is heated. Wide assortment of all kinds of cords, there are small spools as well as professional spools up to 500 m. Not found.
“Champion Produce superior coaxial yarns with abrasion resistant coating. All cords of this brand have a very high abrasion resistance. With standard use, 15 meters may be enough for the whole season. Sometimes some lines stick together in the reel and are difficult to feed.
“Husqvarna High quality is guaranteed for all types of thread. The product range is wide, the lines have a special patented surface finish, resistant to sintering, delamination, elasticity and durability. Not found.
“Echo Good cords in a wide assortment. Titanium Power Line, a two-core line with excellent cutting power, deserves special attention. Some lines (e.g. Silent Spiral Line) break quickly.

It should be noted that even the highest quality line can behave differently in different conditions. To avoid disappointment, it is important to follow the rules for storing and operating trimmer cords.

How to remove the fishing line

To change fishing line in your trimmer, remove the head cap. To do this, press the catches on both sides of the cover with your fingers and pull the cover upward. This will expose the spool. Then pull it out by pulling up on the axis on which the reel sits. If the ends of the fishing line are sticking out of the head holes, then lift the spool up on its axis and pull the rest of the line out of the holes in the head. Now the part holds nothing and it’s easy to remove it and remove the remaining working thread.

The reel is divided into two parts by a central partition with a cutout. Different models have different size parts, so you need to check how much fishing line can be wound on a reel. Its length varies between 1 m and 4 m.

What is the best line for grass trimmer??

The speed of an electric or brushcutter is largely influenced by the quality of the line. How properly it is wound on the mowing reel determines the consumption of the cord itself, as well as the load that affects the engine. In this regard, every gardener needs to carefully study the rules of selection and independent installation of the line on the spool. This will prevent premature breakdown of the grass mower and make its operation on the garden plot more convenient and efficient.

Cord varieties

Despite the fact that the latter option is notable for its simplicity, because you should only take a fishing line, but there is no practical benefit in it. This is because the choice of material depends not only on the grass trimmer head, but also on the total power of the machine. The parameter is important to consider, because only it will allow you to choose a durable version.

Today there are four types of cord, each has a number of positive and negative sides:

  • Cells with a cross section up to 1.6 mm. Most often such designs are present in electric trimmers, which have a power indicator does not exceed 500 watts. This type is designed for lawn maintenance or for cutting small amounts of grass. You can buy grass trimmer fishing line in a store or order online.
  • Products with a cross section of 2 to 2.4 mm. This version is ideal for petrol and electric lawnmowers with an engine power of 500 to 1000 watts. Cords with such an indicator perfectly cope with thick and thin grass, which will help eliminate overgrowth in a short time. With twice the power rating of the previous model. Therefore, it is not changed very often.
  • If a gasoline grass trimmer is used, the power of which exceeds 1000 watts, it is best to use lines with a cross section of 3 mm. The option will help get rid of not only thin grass, but also vegetation with thick stems. Wear and tear is not as fast as with previous models, especially if you do not load the consumable.
  • But this is not the limit. Also, some manufacturers offer to buy lines with a section of 3.3 mm. Of course, this option has quality characteristics, but will only be suitable for equipment with high power. And such units are not bought by all users, so the demand for such designs is low.

If there is a dacha plot or a large plot of land near your individual house or cottage, then you need to use a lawn mower for easy removal of grass and weeds. In case you are thinking about choosing an electric lawnmower or a gasoline mower, then click and you will find the comparative characteristics of different models.

Over time, the line on your mower wears out and needs to be replaced. you can do it yourself. You need to choose this polyethylene thread depending on the model of the mower. It is also worth keeping an eye on the other parts of the machine, for example you will find information about the blades for the Craftsman lawnmower, which also wear out and can lead to irreversible consequences.

trimmers, line, fast

The device of the spool, in which the line is inserted, is very simple. But it differs depending on whether the spool works with one or two tendrils of thread. It’s important to follow safety precautions when changing the line in the reel.

Your lawn should always look neat and tidy, and should be regularly mowed. Fortunately, modern technology allows you to solve this problem without excessive physical effort. Electric grass trimmers are so easy to operate and maintain that even a teenager can mow with them. The main thing to figure out beforehand how to tuck into a grass trimmer.

How to load a line in the trimmer for grass?

So, we are faced with the task. to correctly load the line into the grass trimmer. Let’s find out in details, where to start and what hidden dangers can wait for us in the process.

See also  What oil to use to lubricate the gearbox of a gasoline-powered trimmer

At the start you need to choose the correct line. Although at first glance all lines sold at the market or in the store are not much different from each other, you should not buy it at random. Not to err in choice will not be superfluous to bring a package of used fishing line or a small piece of it, or at least write down the model trimmer for grass. The ideal option for almost all trimmer models will be a fishing line with a thickness of 3-4 mm.

To perform this operation, the grass trimmer must be unplugged and turn the working head upside down. The further course of action depends on the grass trimmer model and the design of the reel itself:

  • for small bottom-mounted trimmers, press the buttons on the sides of the reel and remove the top part of the reel from the head;
  • for trimmers with a bent rod, use one hand to clamp the spool body and at the same time turn the wing nut located on the body counterclockwise;
  • for straight bar trimmers with a gearbox, put a screwdriver in the hole under the spool and turn the body of the spool counterclockwise.

Once the spool has been removed from the head, it must be carefully disassembled. It is better to do it on an already mowed area, as there may be a spring inside the spool, which will be quite difficult to find in tall grass. After disassembly we have three parts: the body (upper cover), protective cover and the spool.

Step 4. measuring the necessary amount of fishing line

Beginner mowers usually ask how many meters of fishing line should be spooled on the grass trimmer reel? There are two ways to resolve this issue:

In any case, after the winding is finished, the coils of fishing line must be on the body of the spool, not slipping off it. Don’t try to wind it as much as possible, it will not unwind well and will break more often.

Step 5. winding the line onto the spool

trimmers, line, fast

How to install the line on the grass trimmer depends on the design of the spool. Let’s see the version with one line exit in the body of spool. In this case, the end of the line is clamped in the cleft of the spool, and then wind the line, trying to lay the coils as tightly as possible. The direction of winding should be opposite to the direction of rotation of the spool and is usually indicated on the inside of the spool. When you have finished winding the spool, you need to put a protective cover on the spool and lead the end of the line into it

If the spool is designed to work with two tails, the line should be folded in half and placed in the groove in the central part of the spool. Further winding will be carried out by one or two slots, depending on the design of the spool. The winding direction must also be opposite to the direction of rotation of the bobbin. At the end, the line tails will also need to be led out into the holes on top of the spool.

The line in the trimmer head may run out at the most inopportune moment when work is in full swing. To avoid time-consuming and time-consuming explanations of the instructions, we recommend that you familiarize yourself with the process in theory beforehand. From our article you will learn all the subtleties, from the choice of consumables to winding on different types of spools.

Process of line replacement

Each trimmer manufacturer recommends a line, or cord, of a certain diameter. the reel is made for it. It can range from 1.2 to 4 mm: you need to look at the manual, which sizes of fishing line are allowed for your tool. For example, many trimmers have a maximum value of 3mm (recommended for hard grass). thicker cord cannot be installed. For mowing young, soft vegetation, a thin line with a diameter of 1.2. 1.6 mm. Also observe the cord structure when selecting: round cord is the strongest and best suited for coarse grass, and curly cord. For soft, twisted or notched line. for thinner stems. Depending on what kind of grass grows on the property. lawn or weed, buy the appropriate consumables. Coil length varies from several tens of meters to several hundreds of meters, and its price depends on it. The amount of line to be spooled depends on the material to be spooled. If the grass trimmer is used in a private household, there is no need to buy a reel of more than 100 m.

2 to 4 meters of line is needed for one filling of the bobbin. depending on line thickness and manufacturer’s recommendations. If you wind more than this, it will be difficult to move the line, and you may have problems pulling the new ends in the process. Coil out the necessary amount and cut with a knife.

To insert the line into the trimmer head, you must remove it from the tool. Depending on the design, this can be done by pressing the catches or unscrewing the thumbturn. Note the direction of thread. right or left. and depending on this turn the knob. The direction of rotation is normally indicated by an arrow on the trimmer head body. It is recommended to perform this operation with gloves on. no slipping of the fingers and no dirty hands.

The line is wound on the bobbin, which is hidden in the trimmer head body. To get to it, you need to disassemble the element. On the body provides the latch latches, by pressing them cover can be easily removed. Sometimes disassembly is performed by unscrewing the body.

trimmer heads differ in design, type of spool and how the line is pulled. Once you disassemble the housing, you will see the bobbin and determine what type it belongs to. There are products with a rim in the middle that divides the reel into a top and bottom for each end of the line. In products without it, the line winding is continuous. To make the process more understandable, we suggest using the table.

See also  How much fishing line is needed for the grass trimmer?

Winding line on different types of spools

We have described how to wind the line into the reel of a grass trimmer with two tendrils. This is the most common suggestion. But there are other ways. For example, if the mowing head has only one pinch point, the line is wound without folding. Rotate in the direction indicated on the bobbin case and temporarily fix the free end of the cord in the slot on the case. For four-pole trimmers, four short pieces of line are used and are inserted one at a time into the slots in the assembled head.

After the line is wound on the bobbin, you need to assemble the body. Position the spool so that the line ends can be pulled into the exit holes of the trimmer head. Slots in the bobbin, where they were temporarily inserted, will not let them slip out. If not, use your fingers to hold the ends of the coil when placing it in the housing. After inserting the loose ends into the exit holes, close the cover and secure it with the latches or screws. Set the mowing head on the grass trimmer and pull the line ends to the desired length so that they do not touch the guard during operation. Done! You are ready to go to work!

So, if you know the theoretical algorithm of line replacement in the trimmer head, you can easily and quickly cope with the task. Most importantly, take your time and look carefully at the construction of the bobbin before you change it for the first time. If there are difficulties with disassembly of the body, you can always refer to the instruction manual, where the fixing mechanisms are necessarily specified. This helps to avoid unnecessary malfunctions. Buy fishing line and other consumables for your trimmer in our online store.

Types of Cords

Of course, the option to come and show the line to the salesman is reliable, but it is not quite right. And this is explained by the fact that the choice of line depends not only on the trimmer head, which is used in the design, but also on the power of the unit.

There are the following varieties of lines:

  • Cords with a cross-section of up to 1.6 millimeters. They are used mainly in electric trimmers, where the motor power indicator does not exceed 500 watts. Tools perfectly cope with the trimming of lawn young grass in small areas. You can buy a line for a grass trimmer on the website of the online store.
  • Cords with a cross section of 2 to 2.4 millimeters. They can be found in gasoline or electric trimmers, in which the power indicator lies in the range from 500 to 1,000 watts. Basically, such equipment is in demand when cutting thin or dense grass, to get rid of weeds. If a 1.6 mm line is installed in these machines, it will quickly deteriorate and need to be replaced.
  • 2.4-3.3 mm cord. is used in petrol trimmers, where the power indicator is more than 1 000 Watts. Such a line is good for grass, as well as for thick and dried stems, allowing you to trim bushes and trees.
  • Manufacturers also produce lines over 3.3 millimeters in diameter, but they are rarely used. It is better to buy it for a high power grass trimmer.

How to choose

The main criterion for line selection should be matching the diameter of the line to the trimmer, its power, and capabilities.

The line must be suited to the cutting task. a 1.4-mm round line would be useless for cutting younger bushes and dead wood.

It is not necessary to put the whole coil of fishing line in the reel, a small segment is enough to prevent spontaneous crumbling of the working head, the more so that to work with the trimmer it is necessary to select the line in the size range specified in the manual. a light thread of small diameter is just as harmful to the tool as a thicker thread.

line material

The material of the line determines how long it will last. Most of the cores are made of nylon, which is characterized by high abrasion resistance, flexibility and strength. The material is easily drawn, perfectly withstands temperature changes and considerable loads. Nylon line has the highest price/quality ratio.

trimmers, line, fast

When greater reliability is needed, a line with a metal core is available. It is composed of two layers: a flexible outer sheath is placed on the rigid basis. This design provides less wear and tear and a 30% increase in strength over nylon line cutters.

Two-component fishing line was designed for the needs of utilities and professional organizations engaged in landscaping along roadsides or railroad tracks. But now it can also be found in the household.

Among the disadvantages of these lines are the high price and the power requirement of the tool. Installing a brushcord in machines under 1.5 kW is not recommended.

How to Attach a Chain to a Grass Trimmer

With the advent of summer, many owners of homestead plots are concerned about how to set the

blade on the grass trimmer. vital are the questions, why and when it is purposeful to substitute the line on the brushcutter with a stronger cutting element. In our article we will try to analyze all this and give useful tips for gardeners.

Why do you need to put a knife on the trimmer for grass

Grass trimmers with a blade attachment are great for cutting the tallest, toughest grass in your home more comfortably. The line on a brushcutter is no match in such cases. The narrow one tears very quickly. How to attach the correct blades to a grass trimmer (lawnmower). Implementation of the thick 2.A 3 mm cord or self-made rope rods force the vegetation to wind up on the bobbin. This increases the load on the engine. As a result, the piston group and other mobile units of the machine wear out very quickly.

If you create a mowing weeds electronic trimmer without a knife, a single line, even if it is thick with a figured section, the case can not solve. There is always a risk of overheating the electric motor and damaging the flexible shaft. And the matter is in the high torque of the electronic motor. Grass wound on the spindle makes a strong resistance to the shaft, reminiscent of speedometer cable, which can not withstand and twist.

See also  What kind of fishing line for a grass trimmer

In order to save technique from early wear and tear manufacturers have provided the ability to install on trimmers for grass special knives. The design and shape of available cutting parts can easily handle not only the coarsened and overgrown grass, and successfully beat with a young bush undergrowth.

READ How to choose a file to sharpen a chainsaw chain

What blades to put on the electric and lawnmower

Before to take and put on a brushcutter blades find out what they are and in what cases are used. Nowadays manufacturers offer the consumer a huge number of types of these consumables. In general, all cutting tools designed for mowing the grass can be systematized:

The main material for the production of trimmer knives can be plastic or metal. Implementation of such expendable parts in almost everything is dependent on the 2-inch characteristics:

For safety reasons, manufacturers are not advised to put on an electronic grass trimmer iron knives. Virtually all trimmers working from the electronic and battery-powered network are equipped with blades of plastic. trimmer for grass Huter delivery options, stores on the mounts and how to put the hood of the other. Depending on the manufacturer they may be of solid disc construction, with several blades or in the form of a special mowing head with removable plastic blades.

Old chain from a chainsaw.

Every so often when mowing in new places we get in the way of not a fixture so bricks and a new knife turns

A timeless line for a brushcutter from a bicycle chain

A timeless line for a chain brushcutter

A straight bar for gasoline grass trimmers and a curved one for electronic trimmers

The iron blade on the electronic grass trimmer does not allow its design features.

  • The curved boom of the machine reduces the distance from the working part of the machine to the mower’s legs. In case of a collision between blades and a stone or other hard object, the grass trimmer will be thrown to your feet.
  • The highest torque, which we mentioned above, in case of a collision of an iron blade with a rigid object, transmits a huge load to the flexible shaft of grass trimmer and its engine. For example, it shows how to put a chain on a Makita electric saw. On the hood, the grass trimmer. What causes them to fail early.
  • The handle of an electric mower in most cases does not have a limiting strip that acts as a stop. That does not prevent feet injuries.

READ Petrol grass trimmer Ggt 1000t Video

Exactly these features make it possible to use only plastic blades on electronically powered trimmers. When hitting an obstacle, the blades break enabling the mower’s legs to be safe from possible injury.

Plastic blades are excellent for cutting overgrown and dry grass. They can mow nettles and burdock trunks.

The use of iron blades only on gasoline-powered trimmers is justified by their design features.

  • Smooth boom design extends the distance to the legs for total safety.
  • Comfortable U-shaped and J-shaped handles let you hold the tool firmly. D-handles of brushcutters are equipped with a limiter that rests against the leg of the mower, which prevents the head from being let down by the legs when the cutting disc meets a hard obstacle.
  • Clutch internal combustion engine allows you to smoothly gain speed to a reasonable level. And when the blade collides with a hard surface, it can absorb some of the impact.

Thus, gasoline grass trimmers with an installed iron blade are best used on large areas. They with furrole not only manage with the highest coarsened grass, weeds, burdocks and nettles, and bushes, as well as young trees.

The shape of the blade on the blade trimmer for grass

doesn’t have any effect on the quality of the work you do. Alpha? Put a 44 sprocket on the wheel from an f-50 and a chain from an alpha. like you do on a scooter. They don’t affect the speed either. Triangular, trapezoidal, rectangular shape is an advertising move by manufacturers.

READ How to Change the Coil on the Husqvarna Grass Trimmer Video

If you’re planning to make hay, it’s ideal to put blades with a huge number of blades on your brushcutter. Pay attention to discs with eight teeth or discs with 4 large blades and 4 additional ones. The 2 or 3 blade blades will really shred the grass.

How to put the right knife on the grass trimmer

Put a knife on the grass trimmer is not so difficult. How to correctly put a knife on the grass trimmer (lawnmower). The manufacturer equips its tools with a special pin that allows you to lock the gearbox and a key, with which the bobbin with the fishing line is unscrewed. The most important thing to follow when changing cutting parts is safety and the sequence of disassembly.

The method of installation of the blade on the grass trimmer is as follows:

  • Remove the protective cover;
  • Lock the drive. To do this, you need to coordinate the two holes. in the hub of the shaft and in the cup of the gearbox. Once they are aligned, insert the pin in the holes;
  • Unscrew clockwise from the hub of the bobbin with a fishing line or the nut holding the dust cover (if the grass trimmer has not yet been used);
  • Next, install the cutter blade, so that the slits on the hub washer coincide with the notches in the cutter blade hole;
  • Install the duster;
  • Tighten the attachment nut (counterclockwise) while holding the locking pin;
  • Tighten it, using a pipe wrench;
  • Putting back the protective cover.

You see, there is nothing complicated about. Now you can safely start mowing the weeds on the property.

Related Posts

| Denial of responsibility | Contacts |RSS