Trimmer line breaks on the trimmer for reasons of
Replacing the grass trimmer line with step-by-step instructions will allow even the inexperienced in such matters the owner of a lawnmower to perform quite complex work.
However, before you begin work on replacing the fishing line on the trimmer, it is necessary to ensure the safety of the work
In particular, you should take precautions to prevent the lawnmower from being switched on carelessly or unintentionally:
- exclude spontaneous start,
- Remove the battery pack (if applicable),
- place the tool on a comfortable place to work.
Work on the replacement of the trimmer line for grass is convenient to perform when the lawnmower is lying on the table, and the master, who performs the replacement of the trimmer line for grass, is able to approach the tool from any side.
Why trimmer line runs out fast in a trimmer
Step-by-step annotation, how to wind the line for trimmer on the grass trimmer spool
With the advent of spring you often spend their time in the country or homestead. Grass trimmer will protect you from such a problem, as grass and weeds. This tool easily trims and mows grass in difficult areas where an ordinary lawnmower can’t do it.
Trimmer for grass. a very effective and successful tool for mowing grass along the fences, flower beds, houses and rows in the garden. There are a number of types of garden trimmer for grass (gasoline, electronic and battery). When suddenly the dacha runs out of line for a trimmer.
The trimmer line runs out of line why. It would seem that everything is fine, your arsenal is such an excellent assistant, but over time, the cutting element wears out and there is a need to replace the finished line. And how to tuck the line for the trimmer in the grass trimmer, not everyone knows.
We suggest using the step-by-step annotation with photos attached.
Instructions on how to wind the line for trimmer on the grass trimmer spool
Saving line for lawn trimmer trimmer! Super way to!
Also look how easy it is to make a spider for grass trimmer fishing line: Measuring jug.
Free fishing line for grass trimmer / DIY rope for lawn trimmer
This video about making fishing line from a plastic bottle. There are a lot of uses for such rope. User daniil malakhov asked a question in trimmer trimmer line ends why. From the perform.
In this article we figured out how to wind the line for trimmer on the grass trimmer spool. And if you’ve done it right, when you press and hold the bobbin, it should pull out again. line for trimmer for grass trimmer. a very important element, without which the tool loses its functionality.
This is essentially the heart of the grass trimmer. That’s why you should buy at a specialized gardening equipment store and choose with special attention. How to change a line for a trimmer in a trimmer. What runs out quickly and poor quality trimmer fishing line in it.
When buying a new trimmer line, be sure to compare it with a piece of the old used cutting element.
Types of trimmer heads
Grass trimmer head is a cylindrical body, in which a spool (bobbin) is inserted with a fishing line (cord) tucked into it. This design can be installed on both gasoline and electric trimmers. The heads differ in the way the cord is threaded and fed and come in 3 types.
- Automatic. The filament is fed after the user has reduced the engine speed. Although automatic line feed is convenient if you do a large amount of work, but such bobbins have one drawback. high consumption of thread.
- Semi-automatic. The use of this type of head does not require the user to perform complex manipulations. Their operating principle is designed so that the cord is lengthened automatically while the machine is running at full speed. It is enough to slightly knock the grass trimmer head on the ground (this removes the cord lock), and the line for the trimmer thanks to the centrifugal force is extended from the bobbin, after which it is cut to the required length by the knife, located on the protective cover.
- Manual. To extend the cord, it is necessary to stop the machine, after which the line for the trimmer is pulled out manually.
Based on the above, semi-automatic bobbins are the best option. Also keep in mind that grass trimmer reels for grass come in single strings (used only for trimming grass) and double strings, which are used for mowing tall grass and small, with thin stems of shrubs.
Read also: Ëerka or die, what’s the right one
Problems with the line
Users of trimmers, both gasoline and electric, sometimes have problems with the cord. “Advanced” mower owners easily cope with the difficulties encountered, understanding why it happens, but for beginners. it is a problem that has no rational explanation. But in fact, everything is solved quite simply. The most common problems that occur with fishing line are.
If the trimmer line tears frequently, it can be caused by the following reasons:
- Stones, small branches and other hard obstacles are caught in the grass;
- The user mows the grass against the fence, and if it is mesh, this breaks the “tendrils” even faster;
- poor quality cord (it is recommended to buy a good quality cord);
- Outlets in the mowing head are worn out, causing the trimmer line to rub against the sharp edges of the sleeves and break (complete replacement of the part will be required).
Cord stress is high
In general, the filament runs out quickly if you frequently bang on the ground with the semiautomatic head or press it down hard. The reel is unblocked and the trimmer line is cut with the knife as it lengthens. Another reason for the fast running out of line is that you often cut the engine speed too low when mowing. But as we remember, the automatic head is designed in such a way that a new batch of line is fed with each decrease in RPM, so it is used up quickly.
Cord does not hold
The filament unwinds if the spring in the semiautomatic head is loose. the line for your trimmer is constantly being pulled out and cut by the blade on the housing, leading to increased consumption. To check this, remove the cover and operate the machine. If the trimmer line “got”, it will be necessary to replace the spring.
Why your line keeps slipping out and unraveling (Solution) / Jon’s DIY
trimmer line flies out
The reason why the filament unwinds after the machine has been started may also be a spring inside the mowing head is loose. In addition, there are cases when the mowing head breaks when the machine is turned on, and the spring installed in it is lost. Inexperienced users may overlook the spring and assemble the reel without it. So the cord does not hold and the centrifugal force causes it to fly out.
The cords are not fed in and the spool does not spin
Automatic or semi-automatic head must feed the line to the trimmer without stopping the machine. But if it does not come out, the reasons may be as follows:
- the line for the trimmer is not wound correctly in the reel, due to which the latter does not rotate;
- the cord is wound unevenly and the thread may get caught between the coils (the thread should be wound carefully, with no twists);
- From the holes come out too short ends of the filament, which is why there is not enough centrifugal force to extract them, and the line for the trimmer is not fed (it is always recommended before starting the machine to adjust the length of the cord, pulling it up a little);
- The line for the trimmer is sticking together (will be discussed later).
Filament sticking together
This unpleasantness is most often due to the use of low-quality cord. During operation, the head of the trimmer for grass heats up, and low-quality filament for trimmers in it melts, sticking together. Threads also sintering occurs when the line meets a solid obstacle. In this case, there is a sharp braking of the cord, after which it is pulled into the head, where it is stuck. Some machine owners recommend oiling the filament with mineral oil or spraying it with silicone spray after winding it on the bobbin. Others advise to wind less thread on the spool. But it’s better to buy a quality product, in the manufacture of which the manufacturer has taken into account the factor of overheating the head, and the thread will not stick.
Can I mow grass with a trimmer??
An electric or battery-powered weed trimmer is a little different from using it to remove weeds. Since you’re trying to get even a cut, keep your head at ground level and make short sprawling motions while trimming. You must also be careful not to cut what constitutes grass too short.
Grass trimmer string, also called “weed eater,” “whip blade,” “whip whip,” “grass trimmer,” “brush cutter” (in Australia and New Zealand) or “strimmer” (in the UK and Ireland). is a garden tool for cutting grass and ground cover, which uses a flexible monofilament. Trimmer line instead of the blade.
The gasoline works, but it won’t turn. How to Get Started Diagnosing Motocuts |
If the cutter does not start or stalls immediately after starting, all major components and assemblies should be checked sequentially. The check algorithm is as follows:
- Fuel tank (fuel quality);
- Candle and candle channel;
- Air filter;
- Fuel filter;
- Exhaust duct.
Why does the carburetor on the trimmer overflow grass trimmers and chain saws Husqvarna Carburetor adjustment Husqvarna make adjustments if: the motor run-in period has ended (after using the first 4-5 liters of. fuel); the quality of the components of the fuel.
How to tuck lines into the STIHL grass trimmer reel Petrol or electric grass trimmer. An indispensable aid in the arsenal of the modern cottager or homeowner. Thanks to these gardening devices, you can easily mow even a large garden. After purchasing this tool.
How to wind the line for the trimmer on the reel of the electric trimmer St For a comfortable mowing of vegetation on the homestead the optimal choice of characteristics of the trimmer for grass will not be enough. For both an electric grass trimmer and a gasoline-powered brush cutter, the cutting tool should.
These assemblies are often the source of serious problems that can be solved after a thorough inspection.
Checking the Fuel Mixture
Check the fuel mixture and its quality before starting the engine of the weed whacker. Do not be thrifty, greedy, or wise in this matter. Repair or replacement of piston group will cost you too much (sometimes up to 70% of the cost of a new tool). It is necessary to prepare the fuel mixture strictly according to the instructions. Calculate its quantity from real needs. Excess gasoline left behind loses its quality over time.
Diagnose the spark plug and spark plug channel
If the quality of the fuel mixture is not in doubt, and the brush stops on start-up, the cause may be a full spark plug. Here, ordinary spark plug wrenches (every motorist probably has them) and spare spark plugs will do for repair.
- We twist the candle and wipe it off;
- Dry it thoroughly (don’t burn it);
- Excess fuel in the chamber is drained through the spark plug hole and dried;
- We remove the old candle with a deposit folder or a lady’s folder;
- Set the gap to 1 mm (you can check with any coin);
- Put everything back in place and try to start the grass trimmer.
Dry the channel for at least 30-40 minutes. Otherwise, there is a risk of refueling a new spark plug.
If the candle works, the socket is completely dry and you do not want to run the brush completely, lubricate the threaded connection with gasoline. This should be slightly dampened. No matter how wonderful a spark the candle produces, a dry chamber just won’t ignite.
If the grass trimmer engine still won’t start, you should rule out a lack of spark due to poor contact between the spark plugs and the high-voltage wire. If the connection is good, but there are still no sparks, your ignition unit has probably gone by. You can’t do without a handyman here, because the item is not repairable, but is sold as a whole.
String Trimmer Line Won’t Feed Properly | How to Fix Feeding Issues | eReplacementParts.com
Diagnosis of grass trimmer filters
Another reason is that the gas grass trimmer may be an air filter. To turn it off, try removing the filter and running the grass trimmer without it. If possible, you will have to replace the air filter with a new one or at least blow and thoroughly clean the old one.
The gas grass trimmer may not start because the fuel filter is dirty. This is the next step in our algorithm. Here we check the condition of the filter element and, if necessary, replace it with a new one. When replacing, try not to leave the intake tube completely without a filter, which is prohibited by any instruction manual. Success may result in the repair of the engine piston group.
Composition of the fishing line
But in general, it is not the shape or diameter of the line that determines how long it will last, but the kind of compound it is made of. The most common domestic manufacturers use nylon as the base material.
It is sufficiently flexible, elastic, strong, and can be deformed by pulling. Relatively easy to handle heavy loads and high temperatures.
Nylon trimmer line is the cheapest in the price range, but this does not mean that it is of poor quality, if we consider the price/quality/performance ratio, then the nylon trimmer line will show a very decent result.
Coaxial, two-piece trimmer line is the strongest and most durable. Its secret is simple. a dense, even tough core and a rather elastic outer layer.
This combination allows the line to retain its properties for a long time and to wear out gradually, much slower than a nylon line.
trimmer line with a metal core was originally designed for professional work. mowing grass along highways, cleaning steep hills, working on rocky terrain.
And therefore has the corresponding price, which is not quite suitable for work in the homestead.
What is needed to replace the cord
When grass trimmer is used regularly, the discs will get blunt, but they can be sharpened and continue to be used. Line for the trimmer in the spool tends to run out, so there is a need for filling a new one, for which you need to determine the type of head and prepare the cord of the required thickness and length.
So, the mowing head is a cylindrical body, which houses a bobbin with a fishing line. Such detail is present both on electric trimmers and on petrol mowers of any brand, be it Bosch, Makita, STIHL or other brand. There are three types of heads, depending on how the line is threaded and fed.
The principle of operation of the automatic group heads is that they feed the line to the trimmer by themselves when the mower reduces the engine speed. These designs are handy when working on large areas, but have the disadvantage of high cord consumption. Semi-automatic heads are easy to operate. automatic line feed is performed at maximum engine speed
To release the cord lock, you need to tap gently on the ground with the tool, and then the unlocked filament slides out of the spool. Only cut to length with a blade mounted on the blade guard. Grass trimmers with manual cord feed need to be turned off beforehand, and then pull out the line for the trimmer by yourself.
Reels for electric and gasoline-powered brushcars are available with one or two line wires. The former are used for trimming low grass growth, the latter for cutting tall grass and small bushes.
The string does not extend
In automatic and semi-automatic reels the cord is fed without stopping the grass trimmer. If it doesn’t, then:
the line for the trimmer in the head is wound incorrectly, so the spool does not spin; the filament is wound unevenly, so the cord gets stuck between the coils and does not come out. to avoid this, the filament must be wound carefully, without skewing, coil to coil; ends of the cord, coming out of the holes are very short, the centrifugal force is not enough to extract them, so the line for the trimmer does not come out. before turning on the trimmer for grass it is important to necessarily adjust the length of the thread and lengthen it a little, if necessary; cord sticking.
Grass trimmer coil repair with their own hands
Came to the cottage to mow the grass, began to mow, mowed, snagged a rock and the coil on the trimmer broke, because of the coil back into town for a long time, and it is too expensive, because gasoline burns more than it costs, so I found a temporary solution. I had a thin strip of stainless steel and a riveting tool, drilled holes in the coil and in the strip (not through, the coil has double walls), shortened rivets to 3mm in length (rivet is disassembled and the aluminum part is shortened to the necessary size, then a metal “nail” is inserted back into the rivet), and assembled such a miracle, how long will it last, but about 8 hectares of grass has mowed, it still holds.
2 Комментарии и мнения владельцев
Well done, I think it will work long enough, the metal after all.
I also have a similar experience. on an electric cultivator the body was broken, also by a stone. there is a problem with nibs in general. The grouser constantly pulls stones, and the casing is thin and even without ribs. Like you had to put a metal patch of tin, but I used bolts and screws to the plastic attached. It works for the second season and the rocks do not interfere.