Support wheels for a cultivator with our own hands

Iron wheels on a single axle tractor with their own hands

In addition to the coupled versions, you can also make iron grousers yourself.

These are essentially metal wheels with welded-on spikes that work the soil layer and provide traction. First of all, you need to determine the diameter and size of the spikes, make a drawing of the future wheels. In addition, it is necessary to determine the weight of the future wheels, given that for traction with the soil, it must be large, and in a motocultivator it may simply not be enough.

Homemade grousers

The minimum weight of the wheels should not be less than 20 kg.

You can take the rims from car wheels as a base. The half axle is welded on, and the bearings are put on it. Square-shaped metal plates are welded to the rims. It is necessary that they touch the edges of the rim. Then the plates are bolted to the rim. Then tines are made. the hooks that will go into the soil. They can be made from angles. These are welded on to the wheel rim at around 15 cm from each other.

Zhiguli wheels for a single axle tractor

Before installing car wheels, analyze the topography, type of soil on the garden plot, type of work. If clay substrates are prevalent, use spiked wheel elements. For uneven and rocky terrain, use rubber with a coarse tread pattern.

For most models of small tractors for dachas, any wheels from the car “Zhiguli” as a replacement are excellent. Take advantage of the recommendations when replacing the factory wheels on the motor block:

  • prepare the replacement blanks;
  • on the inner surface of the disk, weld a metal plate, which will act as the hub;
  • Drill holes in it for fasteners;
  • weld the thick-walled tube to the plate;
  • drill holes in the tube for the fixing cotter pin;
  • place the fabricated half-axle with the wheel on the power tiller;
  • secure it with a cotter pin;
  • repeat the steps for other similar elements.

To work comfortably on any type of soil, use winter tires. To make the machine heavier, weld thick metal elements to the hub plates.

Drawing with instructions for making wheels on a single axle tractor

Without a clear plan and vision of the final result and a drawing to make wheels for the cultivator with your own hands will be difficult. Therefore, it is necessary to determine the drawing and then proceed to work.

Drawing of homemade wheels for a cultivator It is possible to make twin wheels, between which a weighting agent will be inserted.

As the basis of a homemade wheel you can take a wheel from “Zhiguli” or “Moskvich”. In the end you need four. Rubber tires are removed from them. Several steel plates of iron, up to 5 cm wide, are welded to the rim, from which you can form a square. The rim of the second wheel is welded to it, and the rubber is put on the ready-made structures.

See also  Cutting an aperture in a bearing wall. Stages of relocating a door opening in a load-bearing wall

You’ll be interested in Michelin summer tires (Michelin)

Homemade coupled wheels on motor blocks can be made in any variety of variations: seating diameters, their weight, width, height of profile. everything depends on the needs and capabilities of the owner of the unit.

How to make wheels for a power tiller with your own hands?

It is necessary to understand that it is impossible to make wheels from scratch with your own hands. It is necessary to find the basis and only after that you can proceed to the formation of improved and useful devices.

As this very base should be used wheels from a motorcycle or from a car. Only the version with a hook can be self-made, because if you don’t use weighted wheels very often, it makes no sense to buy new, expensive products. On our website you can find a specialized article, which details all the features of the creation of grototracks with their own hands.

To expand the wheelbase it is recommended to use extensions for the wheels of a power tiller, because it is necessary to adjust the device to the individual needs of the farmer. over, to broaden the options, you can create iron twin wheels, which have a cavity inside for placing some weighting agent.

Yes, these objects can hardly be used for the trailer of the motorcycle block, but they will be very useful for the machine itself, because they can be created in the case if a person has no wheels from a motorcycle, but is available from the UAZ or “Moskvich”. The advantages of paired wheels:

  • Reduced towing and, as a result, increased productivity;
  • the ability to quickly remove the wheels of the external plan;
  • easy to create at home;
  • maximum surface contact.

Dual wheels are gradually becoming more and more popular, because you can spend a little time to create them yourself.

wheels, cultivator, hands

www.1001z.| author of this topic: Florianne

How to make a cultivator versatile? The main working part of a power tiller is the tiller. All machines are equipped with it (except for electric pots, where the cutting element is replaced by iron pins). It is made of steel, coated with paint and does not need additional sharpening.

the attachments, in turn, are sold separately and can be purchased by the user as required. It allows you to expand the scope of the cultivator, designed for the medium and heavy classes, less often for light ones (depending on the model of the unit). But it is important to clarify the compatibility of the trailer exactly with the specific model of cultivator chosen. For each task. its own equipment

For those who grow potatoes, plow will be indispensable. There are two types of them, depending on the soil dip:

If it is made in good condition, it drives itself into the soil during ploughing. If this does not happen, then the plow is of poor quality.

The tiller is a type of plow. Thanks to the V-shaped coulter, it can be used to make straight furrows for sowing crops as well as to dip the planted plants.

The bulldozer blade, in turn, is capable of replacing the shovel both when clearing snow and earth. Of course, using a blade blade will not make a full-fledged bulldozer, but it can easily cope with small piles of soil.

See also  How to cut a plastic pipe

For lawn owners, the aerator attachment will be useful. Its use helps increase soil nutrition with both moisture and fertilizer. This is accomplished thanks to small holes pierced in the ground by the nozzle needles.

In addition to individual elements, some manufacturers offer sets that include a single type of attachment, and several attachments and everything needed to attach them. They not only save you money on buying attachments, but also time searching for different attachments. So for some models of cultivators you can buy sets of attachments. They include a plow, a dipstick, a pair of grousers, a hitch, which is necessary to connect attachments to the machine, and extension axles.

Compatibility with this or that type of cultivator is individual and can be found when buying at the dealer.

The haymower makes it possible to take care of the grass on the plot in addition to tilling the soil. There are two types: rotary and knife ones.

The former are more productive, but also much more dangerous. The knife ones are very maneuverable, e. g. between trees, flowerbeds, bushes.

Wheel Hoe garden cultivator from Valley Oak Tools

In addition to the attachment itself, you can separately purchase a hitch for attaching it to the cultivator. Most of couplings are multi-purpose and are suitable for all additional tools (plough, ridging plough, etc.).п.).

Air wheels should preferably be fitted straight away if possible. They allow to significantly reduce the time for transporting the cultivator, especially on difficult terrain.

Not superfluous will be and purchase gruntozatsepov, especially the owners of small-sized units. In addition to giving the implement a higher stability, they allow for deeper penetration of the plough.

For electric cultivators it is important to buy an extension cord. Depending on the area of the site can choose the maximum length required. Extension reel with an iron or plastic stand is more stable. Also features a sturdy carrying handle. Equipment

As for protective equipment, both goggles made of special plastic and headphones, or at least earplugs, are needed.

Goggles allow you to reliably protect your eyes from the ground and dust flying from under the cutters. Earhooks and earplugs are designed to protect your hearing from noise damage when working. Of course, special clothing is mandatory, which many people like to neglect.

Canisters for storage of oil and petrol or fuel mixture are not superfluous. Made of plastic, they prevent premature deterioration of fuel and its oxidation, and the special marking on the side is convenient when preparing a mixture.

How to make wheels for your power tiller?

Some self-made men try to make wheels for the tiller with their own hands and not buy them in a store. How to make rubber wheels for a power tiller? No way. They are taken from other machinery where the wheels are sized to be used with a power tiller. You can take the wheels from an old Zhiguli, for a power tiller also fit from a sidecar.

If you want to make your own trestle hooks you will have to do a little bit more work. First you need to take the discs from the car wheels, weld the half axle to them, the rim and claw teeth at the right height and the right distance from each other. Here you do all the work on the wheels yourself, using an angle grinder and a welding machine.

It is important not to overdo it and make the distance between the tines of the grouser no more than 20 cm, otherwise the whole flush of these wheels will be lost. They won’t go into the ground hard enough.

See also  How to cut a glass jar evenly. Method 1 use a glass cutter

The design you see below is also possible. In principle, it is the rim and teeth that are important in the rim design. All the rest you can do as you like. the main thing is to ride.

How to make your own weights for the undercarriage of a cultivator

Weights play an important role in the functionality of a power tiller. Where you work on the fields, on slopes, in wet or sticky soil, the undercarriage of the machine can slip, because it does not have enough of its own mass.

Weights are the solution to this problem. You can make them yourself. For this you will need:

  • disc weights (from 5 kg);
  • Weights from sports barbells (10 kg each);
  • clutch baskets for cars;
  • hexagonal profile;
  • angle grinder;
  • welding machine;
  • Electric drill.

Homemade weights The process takes place in the following sequence. In two small sections of the profile holes are drilled, pancake disks from the bar are attached to them, clutch baskets are welded to the pancakes and then weights are attached. Weights are ready to lift and can be connected to the cultivator.

Installation of weights solves a number of problems and greatly simplifies many problems for the owner of garden machinery.

Tow bar for power tiller: how to make a homemade cultivator and assemble a ripper with your own hands. step by step instructions and drawings

A cultivator is necessary if you want to get rid of heavy mechanical work on your land. Ease of use, versatility, compactness and low price. thanks to these advantages, the cultivator has become indispensable in a small private household or cottage.

With the help of a cultivator you can easily and quickly treat a small area of land, treat hard to reach areas (alpine hills, the land around the fence and others). Cultivators are widely available in garden equipment stores.

You can make a cultivator yourself from simple materials.

wheels, cultivator, hands

Wheels from the car “Zhiguli” on a single-axle tractor

Before setting the car wheels, analyze the topography, type of soil on the dacha site, type of work. Use spiked wheel elements if clay substrates are prevalent. For uneven and rocky terrain, use rubber with a coarse tread pattern.

For most models of small tractors for dachas, any wheels from a car “Zhiguli” are excellent as a replacement. Use the recommendations when replacing the factory wheels on your power tiller:

  • Prepare replacement blanks;
  • on the inner surface of the disk weld a metal plate that will act as the hub;
  • drill holes in it for fasteners;
  • Weld the thick-walled tube to the plate;
  • drill holes in the tube for the fixing cotter pin;
  • put the fabricated axle with the wheel on your power tiller;
  • secure with a cotter pin;
  • Repeat for the other similar elements.

Use winter tires for comfortable work on any type of soil. To make the unit heavier, weld thicker metal pieces to the hub plates.

Related Posts

| Denial of responsibility | Contacts |RSS