Making of the trailing blades for the power tiller with your own hands

Favorite

It should be noted that the same Neva power tillers are equipped with 560/130. By the way, they also suit the models Favorit and Salut, because they are universal. So, in this case, you should respect the width of 13 cm and the height of 56 cm, if the example will be built homemade model. So it does not make sense to separately consider the situation with power tillers Salyut. At the same time, they can be supplied with even larger wheels. Poltava model F700x100.

What sizes should be taken

On the Internet you can find many drawings and diagrams for independent production of grousers. But what sizes correspond to this or that brand? Sometimes it is not specified in the drawings.

So, the most common power tillers are: Neva, Mole, Salyut, Oka, Zubr, Kentavr. Consider the Neva power tillers.

Hoes for Neva power tillers are also perfectly suited for power tillers Salyut and Favorit. Dimensions for homemade tools for power tillers: height. 34 cm, width. 11 cm. These dimensions are shown on the drawing, and all the fine details that need to be observed to work well with the ground are also indicated. By the way, homemade tractors make a bit more than the factory ones, i.e.к. difficult to size accurately. Dimensions for other brands of power tillers range from 34 cm to 70 cm and up.

Read also: Partner 360 chain saw carburetor malfunction

Let’s look at the main functions of the grousers on the single-axle tractor Neva:

  • Better quality of land plowing.
  • The tooling installed makes the single-axle tractor heavier and good to use, which improves the work with the soil and allows you to work with heavy attachments.
  • This product helps you get uphill with a full trailer in a fairly short time.
  • Tines cling to small and large plant roots, pulling them out.

How to make tines for a power tiller with your own hands?

The high price of certain models of grousers provokes many farmers to make them themselves. Competently made homemade products are of high quality, effective and durable, so they are almost as good as ready-made purchased.

The tractor hitch with your own hands on a single axle tractor can be made after carefully studying the drawings. The drawings contain detailed information about the location and fixing of the structural parts.

The easiest way to make the tines is to use automobile discs. The work is performed in this order:

  • Metal plates are welded to the outer surface of the Zhigulov discs;
  • Teeth are made. The appropriate blanks are cut from steel. The length of the tines should be in the range of 15 centimeters for heavy, 10 centimeters for medium and 5 centimeters for lightweight power tillers;
  • Teeth are welded on the rim with the interval of fifteen centimeters.
See also  How to wind the cord on a power tiller starter

Detailed manufacturing instructions can be found on the video.

На что способен сельский тракторист Приколы с техникой #3

Why do we need tool shrouds for the tiller??

The hitch hooks for the single axle tractor are distinguished by their functionality. That is why they are increasingly used by modern farmers.

The equipment copes with such functions:

  • The weight of the walking tractor increases, and various kinds of additional equipment can be used with greater efficiency;
  • enhanced processing of the ground in the eradication of overgrowth;
  • the traction of the machine with the soft soil during movement is improved.

Such grousers are an important design in small and large farming. They do not require any special knowledge and skills for installation and use, so even a novice operator can cope with them.

making, trailing, power, tiller, your, hands

How to make trestle hooks for your power tiller with your own hands: a knowledgeable person

Earthwork is one of the most boring and arduous types of physical labor, so it is important to choose the right equipment. If you do not want to waste extra time, then learn how to make earthworks for a power tiller with your own hands. With the help of this device, you can facilitate any earthworks that every dacha farmer carries out when farming.

The simplest hooks

Two identical disks are cut from thinner sheet metal. A hole is made in the center for the hub and for attaching to the wheel studs. A 10-centimeter deep sawtooth protrusion is cut along the outer edge. Triangular hooks with cut corners are cut from thick sheet metal. They are welded strictly perpendicular to the saw cutouts.

In spite of their unsightliness, self-made wheel hooks made this way have one great advantage. they are heavy enough to provide good adhesion even on muddy or loose surfaces. Driving on dirt is out of the question, these wheels are designed only for the field.

Another economical alternative is to use a steel round 15 mm diameter. A hand wheel from a gate valve on a main gas line can be used, if a pair is available. The lugs are welded to the outer rim and the hub is fastened in the center.

For the following design, you will need automobile rims. This version of the manufacture for the homemade power tiller is optimal. When designing, standard wheel hubs from a car are provided, and the entire set of four wheel rims is purchased. On one pair are installed tires, and the second is needed for heavy soil.

Take a steel corner of 50-60 mm, cut into pieces, which are somewhat wider than the discs. A 60° triangular sector is sawed out in the middle of one side with an angle grinder.

making, trailing, power, tiller, your, hands

A corner is heated with a gas burner and bent around the cutout. The joint can be welded to provide extra rigidity. The resulting blanks are welded to the outer side of the disk, maintaining an equal distance.

The assembly is repeated on the second disc, do not forget about the same distance between the corners. Now you can quickly change the rubber wheels for steel hooks, and there will be no problems with the landing place, because the discs are the same.

See also  Replacement of the nozzle on a power tiller. Causes of malfunctions

The design of the wheels can be simplified. To do this, the horizontal part (rim) is cut off, and steel plates are welded on. This option is suitable for frequent changes of wheels on one type of hub. Soils are matched to the discs.

making, trailing, power, tiller, your, hands

Description and sizes of grottozatsepov for power tillers

As we understood the size of the scratchers depends very much on the weight of the walking tractor on which they are installed. Although heavy tillers are best suited for heavy soils and therefore the higher and wider rims are better suited to cope with stubble or heavily neglected areas. Also, for the high complexity of work, weighting agents are attached to the wheels.

The trailing arm sizes range from 310 mm to 700 mm in height and from 100 mm to 200 mm in width. For example, you can buy 500×100 mm and 500×200 mm tires for the Salyut.

The latter will be functional in combination with a plow. You can buy the same size with a sand filler to help the mounted plow plow plow deeper into the soil. Although, if you have 500×200 hooks, you may make a weighting beam yourself. Wheels with straps sized 700×130 mm are put on a single-axle tractor to work with ploughs, potato harrow and plows.

The simplest hitches

Two identical discs are cut from a thinner sheet. In the center there is a hole for the hub and for attaching to the wheel pins. On the outer edge, saw-shaped protrusions 10 centimeters deep are cut. Triangular hooks with cut corners are cut out of thick plate. They are welded strictly perpendicular to the saw-shaped notches.

Despite the unsightliness, homemade hooks made in this way have a serious advantage. they are heavy enough to provide a firm grip even with soggy or loose surface. Driving on dirt is out of the question, these wheels are designed for field work only.

Another economical option is to make it from a steel circle Ø15mm. A hand wheel from a gate valve on a gas pipeline can be used, if a pair is available. Hooks are welded to the outer rim, the hub is mounted in the center.

For the following design, you need automobile discs. This method of making a homemade power tiller is optimal. Designs include standard wheel hubs from cars, and purchase the entire set of four wheel rims. Tires are mounted on one pair, and a second pair is needed for heavy soil.

Take a steel angle of 50-60 mm, cut into pieces that are slightly wider than the discs. Saw a 60° triangular sector in the middle of one side with an angle grinder.

The angle is heated with a gas burner and bent along the cut. The junction can be welded a little to provide extra rigidity. The obtained workpieces are welded to the outer side of the disk, keeping an equal distance.

The assembly is repeated on the second disc, don’t forget about the equal distance between the corners. Now you can quickly swap the rubber wheels for steel hooks, and there will be no problems with the seating, because the wheels are the same.

See also  Tools for making jewelry with their own hands

The construction from wheel rims can be simplified. To do this, the horizontal part (rim) is cut off, and steel plates are welded on. This option is suitable for frequent change of wheels on a hub of the same type. The discs are chosen accordingly.

Designs for “advanced” farmers

Simple constructions from Zhiguli disks can be easily made, but their consumer properties are not ideal. Therefore, in special cases, there is a need for a homemade assembly of grousers, which are no worse than the factory models, and they can weigh a single-axle tractor well.

To make a complex design is necessary:

  • Steel sheet of 4-5 millimeters for the main circle.
  • Steel strip 50 millimeters, 4-5 millimeters thick for the supporting surface. There should be 6 of them. They give the disc a good reinforcement and make it heavier.
  • Steel sheet of 8-10 mm for making the hooks.
  • Welding machine (automatic or semi-automatic), a drill, an angle grinder, a drill workbench.

All parts are connected by electric welding, as a gas torch will not be able to heat the metal of such thickness.

Due to the fact that the diameter of the grousers is larger than the normal wheels to the motoblock, it is necessary to lengthen their axles.

It is desirable in this case to provide the possibility of adjusting the length of such axes, because in the field the rows may be of different widths. Thus, by moving the wheels with the hooks vertically, you can set them at any level, width and position. In this case the weight of each wheel will not be less than 10 kilograms, and this provides excellent traction with the ground.

You should know that such devices are not suitable for plowing or loosening the soil, although a small amount of soil treatment occurs at the time of driving over the field. For loosening, the trailing wheels on the tiller are not suitable, as an independent fulcrum is required here.

If the design does not have to be heavy, you can make it more beautiful, with an aesthetic appearance. Such wheels can be used on light soils where loosening has been done beforehand. They have a small diameter, in the middle are shaped spokes made of profiled sheet steel. The steel for the hooks should be no more than 8 millimeters, and the weight of the wheel should be no more than 8 kilograms.

Related Posts

| Denial of responsibility | Contacts |RSS