How to work with a hammer on concrete

The most used chisels for peorator how to use

To begin with, you must prepare the tool: lubricate the chuck of the perforator with special fluid for tools and install it back. Further work peoratorom with a chisel is reduced to the following actions:

  • Owners wrap soft cloths around plumbing fixtures. This softens the impact of debris. It is better to work in overalls with long arms, while wearing a respirator and safety glasses
  • Then the grout layers are treated with moist sponges and gently scraped off with a spatula
  • The chisel should be tapped on the wall. In this way you will know whether there are voids in the wall and you will know exactly what to do next
  • In the last step, the cutting edge of the tool is propped up against the selected area and the tool is turned on

Plan to work in impact mode? Then the chisel should be held in the chisel chuck at a certain angle. Drilling begins after the master has set the toggle switch. It is important to hold the tool with both hands and apply it to the place of impact. Depending on how hard you squeeze the trigger, the work speed is adjusted. Of the different types of nozzles fit models with a blade width of not less than 40 mm. To prevent loose materials from crumbling, it is important to ask how to work with the chisel chisel in drilling mode. In any case, tools must be treated with cold water, at least periodically, and their buttstocks cleaned of dust. A flat-tipped chisel will break in half its life if not done.

Is it possible to drill metal with a peorator?

Even a small repair, not to mention professional construction, does not do without the use of a chisel. It can be used to make a hole in a masonry wall or an indentation in a concrete structure. That is why it is worth knowing how to work with the rotary tool, both for the home handyman and for the builder. Also such a tool allows you to quickly and easily drill the required number of holes in ceramic tiles, bricks, wood, metal. And additional attachments will allow, for example, to drill a slab, tamp the material, hammer a rod and even screw in a screw.

Depending on the specific application and availability of accessories, the peorator can be used for a variety of construction operations. But how to do it correctly to avoid tool failure?

What materials can be used with the peorator:

  • Is it possible to screw in screws, self-tapping screws with a torch?? Many professional builders prefer to use an electric tool that can perform the functions of several types of equipment whenever possible. The peorator is one of them. For fast and convenient screwing in screws or self-tapping screws, special nozzles are used. Among them, there are models with a stopper, which guarantee control over the “sinking” of the fastener.
  • Is it possible to stir mortar with a peorator? It is possible, and rather effective at low viscosity of the mortar (for compositions of high viscosity it is recommended to use mixer nozzle and work at minimum speed). An additional argument in favor of such use can be the fact that the speed of the tool shaft can easily be changed. In addition, in its principle of operation, the peorator is not much different from a construction mixer.

Can a peorator drill into wood?? Sufficiently good holes can be produced with the drill. For that you need to use power tool in drill mode and use special drill bits. Depending on material and hole diameter the drilling speed is determined.

Can a tile be drilled with the toranor?? The main problem when working with ceramics is that it can break if handled improperly. That is why it is necessary to switch off the impact mode first of all when using a rotary tool, and it is better to start drilling at low speed with gradual increase of speed.

Can the peorator drill metal?? If a special drill bit is used, it is possible to make holes in almost any material with this tool.

In most cases they have a cylindrical shank and spiral design. They are made of high-strength steel (often based on cobalt alloys).

Drills with tungsten carbide inserts on the cutting part will be more versatile in use.

You will be interested in: “What is the difference between an impact drill and a rotary hammer drill: 7 basic criteria”

Preparing the rotary table for work

Preliminary tool preparation is required if the tool is expected to be replaced in the course of the work. In this case, the following operations are carried out:

  • Removal and cleaning of the chuck;
  • Lubrication of its inner part;
  • setting the chuck with the grease ring retracted;
  • Rotating the chuck to firmly lock it in place;
  • locking after releasing the ring.

All works according to the instruction manual and safety regulations may be carried out only when the rotary hammer drill is disconnected from the mains. It is recommended that the tool be run in no-load operation before use. It is necessary to make sure that there is no extraneous noise, vibrations during the work with the drill or chisel.

See also  Bosch hammer drill 32 how to distinguish a fake

Working with the drill in different modes

It is recommended to start drilling at low speed without pressing the surface too hard. After starting the motor, it must run idle.

This is necessary in order to prevent more complicated consequences in the form of injuries, damage to building structures, complex tool breakage in case of vibrations, extraneous noises or smoke.

A great deal depends on the material characteristics. For example, questions often arise about how to drill metal with a torch.

Experts recommend using only high-quality drills that are specially designed for such operations from proven manufacturers. In addition, it is necessary to properly prepare the surface.

The hole is drilled step by step with a gradual enlargement of the diameter to the required size.

It will be interesting: “How to choose a drill: 8 main criteria”

Drilling mode with impact (drilling)

The common drilling mode designation of most construction tool manufacturers is the hammer drill. Particular attention must be paid during the work to ensure that the nozzle is not tilted. It is also important not to exert additional pressure on the torch, it will not increase the motor power or speed up the work.

This function is not always used. For example, before drilling tiles with a rotary table, it is important to switch off the impact mode and prevent the drill bit from sliding on the surface, which often causes scratches.

To work in impact mode (the toggle switch is turned to the position indicated by the hammer image), special chisel bits are used. During operation the hammer must be clamped with both hands. While you are drilling, you can adjust the chisel speed depending on the work that you are doing.

It is necessary to constantly monitor the tool, because it often happens that the drill inside the construction bumps into reinforcement. If the hole becomes filled with crumbs, it is enough to remove the drill in idle mode in order to clean it (a construction vacuum cleaner can also be used).

Tips for using the rotary hammers

There are a few rules for using the rotary hammers that must be obeyed.

  • Never exert too much pressure on the tool during work, because the auger would be damaged. The power and output are not increased by it in any case.
  • A common mistake is to want to complete the entire operation in one go. The auger should be cleaned periodically.
  • The choice of tooling is determined by the type of work to be performed and the specific features of the tool itself. For example, one type of peorator will require an adapter to change the nozzle, and the other has a quick-release design.
  • No mechanical damage or systematic overheating of the equipment is permitted. Pay attention to models in the aluminum housing, which are always better cooled because of the material properties.
  • When working with the peorator, it is recommended to wear rubber gloves to help dampen vibration, despite the fact that the tool itself is equipped with special inserts for this purpose.

Important to know: “Top 5 drill manufacturers: which company is better”

Estimating Concrete Strength Using the Rebound Hammer | Non-Destructive Testing

Tips for caring for your torch

Properly and timely performance of all maintenance operations depends on the service life and service interval of the machine. Greater attention should be paid to gear lubrication, especially when working with concrete structures, which are accompanied by a large amount of dust.

A good defense against noise is to use a vacuum cleaner; many power tool models are even equipped with a special attachment for securing the hose. It is also necessary to take into account that when working at low speeds the equipment heats up quickly, so constant control of rest and work regime is required.

It is recommended to clean tool from contamination with soft rag after using and disconnection. If necessary, a soap solution can be used. Particular attention should be paid to the cleanliness of ventilation holes. Equally important is to conduct regular preventive inspections of the equipment.

It is also necessary to lubricate the tool shanks before starting work. This is necessary to avoid excessive stress on the bore from friction. If such work is not performed, it can “turn out” in an expensive repair.

How to use the torch. rules of operation

The torch can drill holes in any material quickly and accurately.

The chain saw can replace an ordinary and percussion drill, as well as a jackhammer.

For a proper choice of this universal tool, everyone who has decided to buy it should know how to use the georator, for what works it can be used, what are the differences between different models of georators from each other. It is especially important to determine what work will be carried out with the peorator.

A quality torch with a great number of operating modes is much more convenient in use, and the price for one, even the most sophisticated tool, will always be less than for several tools the functions of which it can perform.

Although there are many types of torches available on the market that differ in weight, size, and power, the work they do is virtually identical. But if you have to drill a large hole in a concrete wall, you will find it impossible to do with a small torch.

How to drill without dust

To avoid dust when drilling the wall, take a plastic bag and tape, preferably painter’s tape. In the right places on the wall mark the holes to be made. Place a polyethylene bag under the mark on the wall with the adhesive tape open so that the dust falls in. When you increase the speed, some of the dust will blow away the motor fan, so you need to drill carefully at low speeds. Then the waste will fall exactly into the bag. It is important to stick the tape very firmly to the wall. With a loose fit, dust will fall between it and the wall, the wallpaper will become dirty.

See also  How to cut concrete at home

What time you can work as a peorator

To avoid problems with the neighbors during the repair, it is worth focusing on the following standards for the permissible noise level.

Types of noise Times of use
Listening to music too loudly, using household appliances, the operation of which is accompanied by a high level of noise: From 8:00 to 22:00
Repairs involving the use of noisy machines (vibratory sanders, demolition hammers, etc.) are often difficult and time-consuming.д.) working days From 8 a.m. to 9 p.m
holidays, weekends prohibited

How to work with a peorator: 7 nuances that are important to know

Even small repairs, not to mention professional construction, do not do without the use of a peorator. It is with its help that you can make a hole in a stone wall or a recess in a concrete structure. This is why it is worthwhile for the home handyman and the construction worker to know how to use the rotary bolt as well as the.

work, hammer, concrete

Also such a tool allows you to quickly and easily drill the desired number of holes in ceramic tile, brick, wood, metal. And additional attachments will allow, for example, to drill a slab, tamp the material, hammer a rod and even screw in a screw.

Depending on the features of the application and the availability of additional accessories, the peorator can be used for a variety of construction operations. But how to do it correctly so that the tool does not fail?

For which materials the torch can be used:

  • Is it possible to screw in screws, self-tapping screws with the torch?? Many professional builders prefer, if possible, to use a power tool that can perform the functions of several types of equipment. Peorator is one of them. To screw in screws or self-tapping screws quickly and conveniently, the special bits and bolts are used. Among them there are models with a stopper that guarantees control of the “sinking” of fasteners.
  • Can the mortar be stirred with the mixer? You can, and quite effectively at a low viscosity of the mortar (for compositions of high viscosity, it is recommended to use the mixer nozzle and work at minimum speed). An additional argument in favor of such use can be the fact that the speed of the tool shaft can be easily changed. And the working principle is not very different from that of a construction mixer.

Can I drill into wood with a peorator?? Sufficiently good holes can be produced with the rotary table. To do this, you need to use an electric tool in drill mode and use special drill bits. Depending on material and hole diameter the drilling speed is determined.

Is it possible to drill tile with a tile drill bit?? The main problem when working with ceramics is that they can break if handled improperly. That is why it is necessary to switch off the shock mode first of all when using the rotary table, and it is better to start drilling at low rpm with gradual increase of speed.

Can the peorator be used to drill metal?? If a special drill bit is used, it is possible to make holes with this tool in almost any material. In most cases they have a cylindrical shank and a spiral design. Material for their manufacture is high-strength steel (often on the basis of cobalt alloys). versatile in use would be drills that have carbide plates on the cutting part.

It will be interesting: “What is the difference between an impact drill and an accelerator: 7 main criteria”

The electric motor of the device

The motor, which is the main element of the device, drives all other parts of the mechanism. It consists of a stator and a rotor, whereby the rotor is a movable part, and the stator is not. The rotor consists of an armature and a collector. Anchor is such a block containing plates of steel. They have copper wire windings wound on them. The collector, in turn, looks like a cylinder. Its design is in the form of a dielectric with conductive plates installed, and the armature windings are connected to these plates. the rotor rotates due to the magnetic flux generated around the rotor by the stator windings which induces a torsion torque. The rotor uses only a constant current and the magnetic flux only ever flows in one direction. The power supply is provided by means of brushes made of graphite. The brushes are positioned to provide electrical contact with the armature.

the brushes should not wear more than 70 percent, if they do, they need to be replaced. Before replacing, pay attention to the brush holder and clean it if necessary.

You can use a multimeter to check the windings. For this purpose, one probe of the meter is installed on the brush holder, and the other probe is installed on the input of the 220 volt power supply. To determine the exact location of the connections, it is easier to use the wiring diagram. If the resistance is infinite the conclusion is that the winding is burned out.

work, hammer, concrete

Working with a peorator in shock mode what you can do

There is one more mode left on the peorator that is a jackhammer. The principle of its operation is that the cartridge on the rotator does not rotate. It makes reciprocating motion, which allows you to chisel, hit, screw through, destroy concrete surfaces. To do this, set the toggle switch on the tool to the chisel mode, which has a hammer drawn on it. Besides, in this mode you need to use the corresponding types of nozzles: pick, shovel, chisel, etc.п., which depends on the technological requirements. When working in this mode, there is no need to exert pressure on the surface to be treated. All the handyman has to do is point the nozzle in the right direction and hold the machine firmly in his hands.

See also  How much noise can you make with a hammer drill?

HOW TO JACK HAMMER CONCRETE EFFICIENTLY

It is not recommended to use the rotary hammer for a long time in percussion mode, unless it is a professional-type tool. If you plan to use the unit often for chiseling concrete, then it is better to buy a jackhammer.

This is interesting! Suitable actuators for all modes of operation are available in the online store Cylinder. In addition, the Cylinder also has various accessories, spare parts, as well as power tools.

Possible faults, causes and solutions

To repair the singer with your own hands, you should first determine the external manifestations of malfunction.

Drill doesn’t kick

If the piston stops kicking when you switch to kick mode, but the auger still rotates, the floating bearing is most likely damaged. The solution is to replace the chuck with a new one.

Second possible cause is a defective hammer mechanism. If the steel bit breaks during overloading, the impact first falters and then does not rotate at all. The bit must be replaced.

The third probable cause is wear or breakage of the piston group. Replace the sleeve and piston.

The chuck will not rotate and does not drill

If the chuck does not rotate in drilling mode when the start button is pressed, the cause can be determined in advance by the sound. If the electric motor is buzzing but does not rotate the chuck, there is most likely something inside the gearbox that is preventing the rotor from turning. What’s wrong with the motor, you have to dismantle the mechanics of the tool to find out.

If, however, the motor does not hum when turned on, it is more likely that a motor failure has occurred. Having opened the lid of the tool, it is necessary to determine what exactly caused such a phenomenon. It can be a power circuit breakage, a broken start button or a short circuit in the winding of the coils. Use a tester to determine the specific cause and make the appropriate repair.

Drill bit not holding in chuck and comes out

Tool bit jamming can be caused by prolonged use. A drill bit or chisel inserted in a chuck doesn’t hold and comes out during work. It is not only impossible to continue chiselling with such a tool, it is also very dangerous. a chisel that has come loose can cause injuries.

The reason for the tool holding up is due to a worn or broken chuck. The chuck must be disassembled and the problem must be determined. Possibly the balls are deformed, or there is a breakage on the limiting ring or the fixing spring is sagging. Usually after the defective part has been replaced, the socket will begin to work properly again.

How To Use A Hammer Drill-Tutorial

Brushes sparking

Brush arcing is a very common phenomenon in dusty work conditions. Arcing is usually caused by wear and tear on the brushes themselves. Correct the situation by replacing the latter with a new one, the sparks won’t fly out anymore.

If not, you need to look in the stator or rotor windings. It is possible that the large amount of dust that has penetrated into the motor has led to abrasion of the protective lacquer that covers the copper conductors. And this causes a short circuit. The presence of a short circuit can be checked with an electrical instrument (multimeter).

Measuring the resistance between the lamellae is done with a multimeter

Preventive maintenance of the tool: replacement of brushes, lubrication of rotor shaft bearings and additional coating of coil windings reduces the possibility of breakages.

Also note that dust may adhere to the bearing grease next to the manifold. To prevent this, the collector should be degreased with a swab dipped in alcohol or solvent.

Too much heat in the motor

If the motor becomes excessively hot during operation, it is a sure sign that the motor is not operating normally. First of all, to prevent overheating, it is necessary to observe the operating mode of the device:

When drilling, it is recommended to use intermittent operation: apply maximum power for not more than 1 minute, then switch on idle for 3-4 seconds.

If the temperature of the housing does not drop, then the motor needs to be inspected. If you can smell something distinctive coming from under the hood, you must stop working immediately and disconnect the unit from the mains. Do not disassemble it until it has cooled down completely.

Chuck not holding the chuck

It may sometimes happen that the chuck and fastener come off while the machine is in operation. This is due to wear of the cartridge body’s mounting on the end of the bushing which is the retaining ring. If it fails, the fixation is broken and during the shock the rubber dust cap comes off, followed by the spring and the balls.

The cartridge can be restored to normal operation by installing a new retaining ring. It is done quickly and does not require any additional tools other than a regular screwdriver.

Related Posts

| Denial of responsibility | Contacts |RSS