How to wind the grass trimmer reel with fishing line

How to change the line for a trimmer in a trimmer

The grass trimmer is the most common tool used for cutting grass and small bushes. This machine is notable for its ease of maintenance, simple operation during work, and thanks to its low weight even women can cope with it. It’s not a secret that high-quality mowing work requires proper selection of cutting tools. As the latter, trimmers use special cutting attachments (discs, knives) or trimmer heads with a fishing line inside. Nozzles and line for the trimmer are an expendable tool, but if the blades can be sharpened, when the line is used up it needs to be replaced. In this article we will tell you in detail about how to change the line for the trimmer.

Grass cutter head is a cylindrical body with a spool with a piece of fishing line (cord) inside. This design can be installed on both gasoline and electric trimmers. There are three types of heads and they differ in the way the cord is threaded and fed.

  • Automatic. The filament is fed in after the user has lowered the engine speed. Although automatic filament feeding is convenient if large amounts of work are performed, but such bobbins have one disadvantage. a high consumption of thread.
  • Semi-automatic. No complicated operations are required from the user when using this type of head. The way they work is that the filament is lengthened automatically while the machine is running at full speed. It is enough to slightly knock the grass trimmer head on the ground (this removes the cord lock), and the line for the trimmer thanks to centrifugal force is pulled out of the bobbin, after which it is cut to the desired length by the knife, located on the protective casing.
  • Manual. Cord extension requires the machine to stop and the line for the trimmer is pulled out manually.

Based on the above, semi-automatic bobbins are the best option. Also note that the grass trimmer reels for grass are single string (used only for trimming grass) and double string, which are used for mowing tall grass and small, with thin stems of bushes.

Advance preparation

First of all, the winding of the fishing line requires removing the spool (bobbin, bobbin) from the grass trimmer. the specific steps will depend on the complexity of the configuration and type of the product itself:

  • small electric grass trimmers with a working motor and spool on the bottom usually have side keys on either side of the reel. When pressed at the same time, the upper part of the spool, along with the internal contents for winding the fishing line, is detached, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring that is part of the construction does not pop out and get lost;
  • electric and gasoline grass trimmers with a curved rod without the possibility of installing a knife, as a rule, have a spool with a special wingnut: in such designs should be one hand to hold the bobbin in a fixed position, and the other counterclockwise rotation of the fixing bobbin on the rod nut, wingnut. After loosening the nut the entire bobbin is removed.
  • Electric and petrol grass trimmers with the possibility of installing a blade on a straight boom (e.g. STIHL grass trimmers) have a hole under the reel. To immobilize the cutter bar, a screwdriver or other suitable object is inserted into the hole and slowly rotated so that the screwdriver fits into the hole and the bobbin is locked in place. After that, the spool housing is turned clockwise (with left-hand thread) and removed from the grass trimmer.

For the second and third cases, depending on the design, the coils are disassembled in different ways. In spools with a wing nut, the wing nut is unscrewed, in spools with latches, the latches are pressed and one part of the spool is released from the other part. If the halves of the bobbin are connected by thread, then it is enough to turn them with your hands in opposite directions until they are completely unscrewed.

How to remove the spool from the grass trimmer and remove the line for the trimmer

Initially, before you can tuck the trimmer fishing line into the grass trimmer spool, you need to remove it from there. The spool or lead is a device that is inside the mowing head, spool or reel. There are different kinds of heads (depending on the manufacturer), but the principle of changing the line on the spool is the same for all. The first thing to understand is how to remove the head from the tool, as well as how to get the drum with a fishing line out of it.

See also  How to choose a battery-powered hedge trimmer

This is interesting!You can replace the tooling directly on the tool, but if you are doing it for the first time, it is still recommended to remove the head, and study the detailed process of winding. Once you have mastered the technique, you can perform the replacement work on your trimmer or gasoline-powered brushcutter. The instructions on how to unscrew the manual head on the trimmer are as follows:

    Turn the tool upside down with the head facing up, and if necessary, clean it of dirt. Grasp the cover locks (on the mowing head) symmetrically with two fingers of one hand. After gently pressing them inwards, remove the protective cap from the reel

This process is not difficult, and as you understand, there is no need to dismantle the entire head if you know how to replace. When disassembling, consider these nuances:

  • Periodically removing the head is recommended to prevent corrosion of the threaded joint. If you never unscrew the screw, it will be difficult and sometimes even impossible to do so if necessary
  • If the screw has a square head bore, then a screwdriver or bits of the appropriate size should be selected for unscrewing in order to prevent the facets on the head from sticking out
  • When assembling the installation should be processed threaded seat with a lubricant, such as solidol or machine oil
  • If the facets on the screw have slipped, you can use special clamping pliers to unscrew it
  • There are reels that do not require prior disassembly. To disassemble them, you should take hold of it, and rotate in the opposite direction of the clockwise direction

Knowing how to disassemble the drum, you should continue to figure out the process of replacing the grass trimmer line. The video below shows a detailed process on how to open the grass trimmer reel and disassemble it.

Winding the fishing line

Inserting the trimmer line into the grass trimmer is not difficult. To perform this operation it is necessary to follow a simple algorithm of actions. The first step is to determine if there is enough consumable material. To make its calculations, you need to wind the line for the trimmer on the spool so that the resulting coil is less than or equal to the diameter of the sides of the construction.

When you’ve decided on the size of the cord, you need to fold it up so that one part is 15 cm longer than the other. Winding the cord begins with the edge that divides the bobbin into 2 parts. Here will be located the fastener, in which you need to insert the thread, bent in half.

Now you need to understand in what direction to tuck the line for the trimmer in the grass trimmer. To do this, inspect the bobbin. often a special arrow is indicated on it. If there is no explanatory information, find the pointer on the trimmer head, and start winding in the opposite direction. Further actions can be divided into 4 steps:

  • Finishing winding the filament. To do this, it is inserted into the side groove on the spool. The second end of it is attached to the opposite slot.
  • The ends of the fixed line are cut. 7-10 cm of allowance remains.
  • The fueled part is placed in the head of the grass trimmer. This is done by alternately inserting and pulling up the thread into the entry holes of the structure.
  • Thread is pulled out of the slots. Once the action is completed, the product cover is secured with clamps.

Once the last step is complete, the garden tool is ready for use. If after inserting the fishing line into the grass trimmer the device does not work correctly, it is recommended to repeat the procedure, changing the thickness or type of cord. Otherwise, the product may fail.

wind, grass, trimmer, reel, fishing, line

Learning how to properly wind the fishing line for the trimmer on the reel of the grass trimmer and lawnmower installation instructions

Owners of private homes know how necessary this type of tool is, as a trimmer for grass. It can be petrol and electric, and they differ in the design of the power units.

For mowing grass in areas where there are rocks, trees and other obstructing objects, a trimmer line is used as a cutting device.

Best Way To Tie Fishing Line To Any Reel. The ‘2-5’ Knot

This consumable wears out during use, so how to wind the grass trimmer spool, we will consider in detail in the material.

What you need to know about the line on the grass trimmer

A fishing line is a consumable that consists of nylon and serves as a cutting tool.

The cutting attachment is used to cut the grass, which is made possible by the high-speed rotation of the tool head.

This material has different thickness, depending on its application to the respective electric low-power tools (1 to 1,6 mm), electric from 500 W (2-2,4 mm) and gasoline grass trimmers with brushcutters (2,4 to 3,2 mm).

The more powerful the tool, the thicker the cutting attachment has to be. It affects not only the quality of mowing the grass, but also the service life of the material.

If you wonder how to wind the grass trimmer spool, then it’s time to change the recharge the tool.

With the advent of spring, this issue is becoming more and more in demand, so it’s time to figure out the step-by-step instructions for replacing the line in the grass trimmer spool.

How to remove the grass trimmer spool and remove the trimmer line

Initially, before you tuck the line for the trimmer into the reel of the grass trimmer, it must be removed from there. Reel or tip is a device that is located inside the mowing head, reel or drum.

See also  How much fishing line is needed for the grass trimmer?

Heads come in different types (depending on the manufacturers), but the principle of replacing the line on the spool is the same in all.

The first thing to understand is how to remove the head from the tool, as well as how to get the reel of fishing line out of it.

This is interesting! Replacement of the equipment can be made directly on the tool, but if you do it for the first time, it is still recommended to remove the head, and study the detailed process of winding. After you have mastered the technology, you can perform the replacement work on the trimmer trimmer or chain saw.

The instructions on how to unscrew the manual head on the trimmer is as follows:

  • Turn the tool upside down, and if necessary, clean it of dirt. Grasp the cover locks (on the mowing head) symmetrically with two fingers of one hand. After gently pressing them in, remove the protective cover from the reel
  • Next remove the spool of fishing line from the reel shaft. It is mounted on the shaft without any fasteners, so you can remove it with one hand
  • The main part of the reel is fastened with a screw, which must be unscrewed with a screwdriver and a suitable bit
  • To unscrew the head, hold the base of the drum with one hand and unscrew the head counterclockwise with the screwdriver with the other
  • After this, you can disassemble it. To do this, you do not need to pull it with all your might, but by rocking slightly to the sides, slowly withdraw from the engagement with the metal shaft on which the drum is planted
  • When reassembling, the screw head should be fitted with a square shaped slotted head

This process is not difficult, and as you understand, there is no need to remove the entire head, if you know how to do the replacement. Consider such nuances when disassembling:

  • It is advisable to remove the head periodically to prevent corrosion of the threaded joint. If you never unscrew the screw, it can be difficult or even impossible to unscrew it, if necessary
  • If the screw has a four faceted head then a screwdriver or bit of the proper size should be selected for unscrewing to prevent the facets on the head from sticking
  • When reassembling the machine, the threaded seating should be coated with a lubricant such as solidol or machine oil
  • If the facets on a screw have worn off, you can use special tongs to unscrew it
  • There are drums that do not require prior disassembly. To disassemble them, take hold of it, and rotate it in the opposite direction of the clockwise direction

Knowing how to disassemble the reel, you should continue to figure out the process of replacing the grass trimmer line. The video below shows a detailed process on how to open the grass trimmer reel and disassemble it.

Depending on the manufacturer, the heads differ structurally not only externally, but also internally. Most reels have a compression spring inside (semi-automatic and automatic).

Above is an instruction on how to disassemble the grass trimmer head without a spring, t.е. on a manual type head.

The principle of disassembling a semi-automatic head with a spring inside is almost identical to the above instructions.

The principle of operation of the semi-automatic grass trimmer reel is as follows:

  • Inside the head is a spool with slits preventing it from moving freely
  • the spool is actuated by a spring, which presses it onto the slits in the cover structure
  • A line for the trimmer is wound on the lead, the length of which depends on the tool itself. This length is usually between 1 and 4 meters
  • During work, if the need to increase the length of the line, there is a pressure on the protruding part of the drum, by which it is disengaged from the slits. At the same time the line for the trimmer is reeled off the drum, increasing in length
  • After releasing the desired amount of line, release the clamp and continue mowing

Обзор катушки для триммера (Быстрая заправка)

The advantage of the spool with a fishing line is that this consumable does not need to be sharpened as compared to metal discs. In addition, if a stone or wood gets in the way, the line for the trimmer simply comes off, without negatively affecting the gearbox and the engine of the tool, as it happens in the case of metal cutting blades.

Knowing the construction and design of the types of mowing or trimmer heads, it is necessary to proceed to consider the process of threading the line into the grass trimmer reel. this is what most special tool owners have trouble with.

All about changing the line on the trimmer head

There are many types of heads for different line types. The latter is also available in several diameters: from 1.0 mm to 3.2 mm. It is available in round (including a special groove for noise reduction), square, twisted and star-shaped.

there is no clear preference, which explains a great variety of shapes and diameters on the market. The round shape is usually stronger, but has a worse cutting ability, in addition, it makes a characteristic sound when rotating. That’s why they sometimes make an acoustic groove on it, however, the use of this line makes sense only on cordless trimmers, machines with gasoline-powered and mains drive have the sound level of the drive itself almost drowns out the sound of the line. A square has a good cutting ability, and despite the fact that such a line for trimmer is less strong than a round line, on average, it is consumed less. A square line for a trimmer can easily cut willow shoots up to 1 cm in diameter. A star has the maximum number of cutting edges, it mows the best and is the fastest to use.

See also  How to mow a lawn evenly with a trimmer. Lawn mower

The next nuance in the choice is the stiffness. The fact that in the manufacture of nylon in it add a modifier (often maleic anhydride), which improves its strength and prevents tearing. However, modifiers are not the cheapest component, people try to save on it. That is why a seemingly good line for the trimmer, which was left for the winter, suddenly behaves completely differently in the spring. it tears, stops to come out of the reel normally. There is a recommendation to soak the trimmer line in water before work, but I do not see much point in this, maleic anhydride interacts with water, but if it is not enough in nylon, there will be nothing to interact with. Therefore, it makes no sense to stock up on fishing line for a long period of time, breaking or constantly tearing fishing line for the trimmer, which also does not want to come out of the spool itself, can significantly complicate the work.

How to choose fishing line for a grass trimmer

The grass trimmer, bought in a store, is already ready to work. it is filled with a standard kapron fishing line. It cuts grass, but it copes with the work poorly. it quickly fails and only mows young, thin plants. Old grass and weeds with hardened stems cannot be cut at all or are difficult to cut, wearing out quickly. Suffices it for a short time, after which you need to replace the line for the trimmer in the trimmer.

It is not recommended to use fishing line for the trimmer, it is better to take a special thread with a core of fiberglass. It is sold in construction stores. Opt for a variant that has a square or triangle cross-section. their sharp edges will work like knives.

Consumption of lines for grass trimmer with faceted and reinforced consumables will be 2-3 times lower, the same amount of output compared to round section lines and lines not reinforced with fiberglass.

Buy the material with a diameter no smaller than the one recommended by the manufacturer. If you do not know the diameter, look at the size of the holes on the outer casing of the mowing head: the diameter of the working thread should be a little less than the hole so that it can pass through freely.

Buy enough cutting filament (for 2-3 changes), try to buy different versions to compare which one will work best.

Once you know how much material you need for one winding, be guided in the length of the line for your next purchases, so that no pieces are too short for winding.

To replace the fishing line on the mechanical mower with your own hands, you need to disassemble the mowing head and take out the spool, on which the working thread is wound.

Instructions with a step-by-step description of how to wind the grass trimmer reel and lawnmower

In order not to make a mistake in choosing the right fishing line for your tool, you should first disassemble the head, and look at the side wall of the spool. This information is usually presented on the tip, which will not allow you to make a mistake with the appropriate jigs.

If the information on the spool about what diameter of line for the trimmer can be charged, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the jig, it remains to figure out how to charge it. There are two ways to do this, but they are not all applicable. Let’s consider both methods in detail, and already depending on what models of brushcutters and trimmers you use, determine independently which variant is suitable.

wind, grass, trimmer, reel, fishing, line

This is interesting! The principle of how to wind the line for a trimmer on the lead of a brushcutter is appropriate not only for self-contained petrol machines, but also for electric trimmers.

Block: 5/8 | Number of characters: 933

wind, grass, trimmer, reel, fishing, line

Spooling line

In the next step we wind up the line for the trimmer, making sure that each end is in its groove. When you have wound it up. the ends of the fishing line should be temporarily inserted into the side grooves.

Then you put the spool in the head, put the cover on top, straighten the ends of the line so they come out of the grooves, and then secure everything with the clips.

For details on how to wind the line for the trimmer on the head of the trimmer for grass, you can see in the author’s video clip. This review is based on a video from the YouTube channel HotSEM.

Related Posts

| Denial of responsibility | Contacts |RSS