How to tuck the line into an electric grass trimmer

How to choose an electric mower for different tasks

tuck, line, electric, grass, trimmer

grass trimmer for country houses powered by the electric network can be used at full power, for cutting tough weeds and mowing thick grass, or can be used very rarely and only for uncomplicated works. For example, to trim the edges of the lawn or care for a small flower garden, several times a season.

Thus, the garden equipment will be subjected to different intensity of loads. To perform them, there are different classes of models household (for the home, vegetable garden, lawn and garden) or professional (for making hay in large quantities, mowing large areas, regular mode of operation).

Therefore, before you choose a grass trimmer for the grass, you need to consider for what tasks and loads it is bought. The necessary technical characteristics of the appliance depend on these conditions. These include:

  • Engine power. Small household up to 500 watts, medium-powered from 0.5 to 1 kW, and the most powerful (used by professionals) above 1000 watts. They have higher cost, but their performance is not worse than gasoline ones.
  • Cutting attachment. The electric trimmers are equipped with a cutting head, inside which there is a bobbin with a line for mowing grass. The ends of the fishing line wear out and new ones need to be pulled. The line is good for mowing around trees, cutting fresh grass. Best electric trimmers have automatic or semi-automatic line feed. Most low-power models only cut with a fishing line. Cutting width of an electric mower is 20 to 42 cm.

But there are also powerful units, with high capacity, which are able to cut weeds with a sharp three-blade knife. The width of mowing with the knife is less than about a quarter of a meter. The option of installing a blade for cutting weeds is only available for those scythes that have a metal shaft inside the boom. If the cable is thin, the blade for hard grass can not be put the cable will burst. This is something to watch out for.

  • The shape of the bar. Trimmers have both straight and curved booms. The curved bar is easier to reach hard-to-reach places, such a grass trimmer has a small weight. But the straight one is more reliable, only it has a strong drive shaft made of metal. Such a boom is made of aluminum. It is much more durable than plastic. On some models, the boom can be disassembled, which is convenient for transportation and storage. Small grass trimmers can be equipped with a telescopic shaft.
  • How the motor is located at the bottom or top. Bottom-mounted grass mower is the easiest and least powerful tool for flower beds and small lawns. It is usually equipped with a d-shaped handle and has a curved boom. You can’t mow wet grass with a top-mounted trimmer.к. it can damage the engine. top mounted grass trimmer is more powerful. Grasshopper with it is well-balanced, mows wet and tall grass. If there are also bicycle handles for a stronger grip and control, you’re looking at a professional tool.

To ensure comfortable operation, pay attention to the selection:

  • Shoulder Strap. A single shoulder strap would transfer the weight of the grasshopper to your shoulder, but a backpack strap would distribute the weight perfectly, reducing the strain on your hands.
  • Low weight. The lightweight model is more convenient to mow grass.
  • Rubber padding on the handles. They reduce vibration and keep your hands from slipping.
  • A trusted and stable brand. The brand name of your electric grass trimmer will determine how durable, reliable and well-built it is.
  • Accidental start protection for safety.
  • Soft start function no jerk on start.

How to fill the grass trimmer reel, types of fishing line

Often, people who have gardens, vegetable gardens, dachas, face the problem of caring for their lawns, with the need to mow the grass. You’ll need a hand-held grass trimmer or an electric grass trimmer. Working with an electric is much easier and faster, the grass is mowed due to the fishing line, which rotates at a huge speed, about 8000 rpm, but from time to time the fishing line wears out and requires replacement. There are many types of it, as well as companies-manufacturers.

The main difference of trimmer line is its diameter. There are several types, starting with the smallest 1.6mm, then comes 2mm, 2.4mm, 3.2mm. the most widespread and often used is 2mm. It is necessary to choose individually for each grass trimmer. If you do not know what diameter to choose, before buying look at the passport of the product, the manufacturer specifies what diameter will be optimal.

As a rule, the more powerful the grass trimmer, the larger the line diameter. For example, a brushcutter with a pretty strong engine has a 2.4mm line, and a 1.6mm line for a smaller engine (about 500 W). The cross-section of the line comes in different kinds. square, round, in the form of a star with sharp edges.

The line is only good for mowing grass, but if you need to mow old bushes, you will need a lawn mower with a knife, only it can do this task.

Most mowers are sold in pre-packages (10m, 15m, 100m) or as cut-to-length lines. The second version is noticeably cheaper, by about half, although the quality is the same. STIHL makes good lines for trimmers.

How to tuck the line into the weed trimmer

This is the question on many minds. In fact, this task is difficult only for the first time, took the spool in your hands, unscrewed the cover, on some models, the thread is left, for this you need to twist clockwise, not counterclockwise, as usual. The left thread is made to prevent the grass trimmer head from unscrewing during mowing. Approximately for filling will need 5 meters of fishing line, cut it off, folded in half marked in the middle, put the center in a special slot, then wind it in the direction of the arrow that is shown on the spool (in the photo it is visible). In this model of grass trimmer (Grinda electric) the place for winding is divided into two parts, it turns out that part of the line is wound into one half, the other into the second half. You put the ends through the hole and close the lid.

See also  How to charge a Makita electric screwdriver correctly

What’s needed to replace the filament

If the grass trimmer is used regularly to cut the grass, the discs get blunt, but they can be sharpened and continue to be used. Fibre in the spool tends to run out, so it is necessary to fill a new one. To do this, you need to determine the type of head and prepare the cord of necessary thickness and length.

So, mowing head is a cylindrical body, which contains a bobbin with fishing line. Such a detail is present both on electric trimmers and on petrol mowers of any brand, whether Bosch, Makita, STIHL or other brand. There are three types of mowing heads depending on how you thread and feed the line.

  • The principle of operation of the heads of the automatic group is that they independently feed the line when the mower reduces the revolutions of the motor. Such designs are convenient when working on large areas, but have the disadvantage. high consumption of cord.
  • Semi-automatic heads are easy to use. automatic line feed is performed at maximum engine speed. To release the cord lock, you need to tap gently on the ground with the tool, and then the released filament slides out of the spool. Grass cut to length with a knife attached to the blade guard.
  • Grass trimmers with manual filament feed must be switched off beforehand, and then you must pull out the line yourself.

As a side note! The most convenient and best priced are semi-automatic cord reels.

Reels for electric and gasoline-powered mowers can be with one or two fishing line tendrils. Use the former to mow smaller grass growth, the latter to cut tall grass and small shrubs.

SuperCut mowing head

This two-string design is also designed for mowing and clearing space and is used at obstacles and the treatment of large areas. For the cutting filament, there is an automatically maintained optimum cutting length. Only for use with a universal or special mowing guard.

Let’s explain how to tuck the fishing line into the grass trimmer reel of these two modifications. Prepare two lines of maximum length (7 m or 10 m), depending on the type of line. These data can be found on the packing list.

  • Hold the head in your hand so that its cap with the bulge in the center is on top. Use your other hand to feel the two notches on either side of the construction. they are exactly opposite each other. Press with your fingers into these recesses simultaneously or alternately until the latch is released and then press the other one. Turn the cover clockwise: it can now be removed and set aside.
  • Take out the spool itself. To do this, twist it slightly to release the plastic hook. With a twisting motion, lift it out of its retention position and upward. The free reel with two compartments will be in your hands.
  • Find the lug that adjoins the separation wall in the middle of the bobbin. Take the line for the grass trimmer and insert its end into this recess until it stops. After bending the string, wrap it around the spool in the opposite direction so that the secured piece of trimmer cord does not fall out of the lug. With firm and steady movements continue to wind up the line turn by turn, trying to distribute the layers evenly and tightly. When the line is over. hook the other end of the line to one of the two notches so that the remainder of about 10 centimeters comes out.
  • Do the same with the second string. The line should be wound into the second compartment in the same direction. Fix the free end of the same length on the notch on the opposite side. The reel can then be inserted back into the housing.
  • Rotate the bobbin to bring the strings and the sleeves in the head together so that they are next to each other. Take each of the lines, gently unhook them from the notch and put them in the special groove to release. Now the ends are sticking out of the bobbin channels and the cover can be closed. Put it on according to the position of the clips and press down firmly until you hear a click.
  • Pull firmly on one string so that the spool body slides up slightly. You will hear another click and some of the line will come out a couple of centimeters.
  • The next step is to cut the ends of each string with a secateurs to the desired equal length, if necessary. STIHL recommends that the fishing line protrudes from the hole by about 10 cm.

Removing the reel from the grass trimmer

Now we’ll take a look at removing the stud from different types of grass trimmers:

  • An electric conveyor belt with a lower motor has two buttons on the sides. With one press of the two buttons, you will need to detach one part of the filling line from the other. Remove the inner part where the strand is wound at the same time as the first half.

Important! While performing the described manipulations it is necessary to be extremely careful so that the inner spring does not accidentally fly out and get scuffed. This small part is a very important “link” that helps in pulling the line on the roller.

Replacing the line on your line/grass trimmer.

  • Body of the electric and gasoline conveyor with a bent metal rod should be held in one hand, and the other. to move counterclockwise the electronic thumbscrew. This small part connects the reel to the grass trimmer bar. After removing the wingtip, you must remove the entire reel as well, while holding the inner spring with your fingers.
  • On electric and ashless conveyors with a straight rod, find a notch under the bobbin, insert, for example, a screwdriver, and slowly rotate it until the tool goes deep and the roller is fully engaged. Next, turn the spool slowly clockwise (because of the left-hand thread) and remove it from the conveyor. Then you will need to disassemble the bobbin, assembled with latches or twisted into a drum. If you have a roller on the latches, then you need to push down on the sides of the latch to release the two parts of the part. After that you should unscrew the thumbscrew.
See also  How to make tractor tires on a single axle tractor

Removing the reel from the grass trimmer

Now we will look at removing the stud from the different types of grass trimmer:

  • Conveyor with an electric feeder with a bottom motor has two buttons on each side. With a single push of two buttons, you will need to disconnect one part of the dressing from the second. At the same time with the first half should be removed and the inner part, on which the core is wound.

RYOBI How to Re-Spool/Re-String 18V WEED WHACKER

Important! When doing the described manipulation, you need to be extremely careful so that the inner spring doesn’t accidentally come out and rub. This small part is a very important “link” that helps in pulling the line on the roller.

  • The body of the electric and gasoline conveyor with the bent metal rod should be grasped with one hand and the other hand should move the electronic knob counterclockwise. This small part connects the bobbin to the grass trimmer rod. After removing the wing nut, you need to remove the spool and the whole spool, while holding the fingers of the internal spring.
  • At the electric and ashless conveyor with a straight rodnu find under the bobbin notch, insert it, for example, a screwdriver, and slowly rotate it until the tool will go deep and the roller is fully secured. Next, you should twist the spool slowly clockwise (because of the left thread) and remove it from the conveyor. Then you will need to disassemble the bobbin, assembled with snaps or twisted into a wingnut. If you have a roller on the latches, then you need to push down on the sides of the clip to release the two parts of the part. After that, unscrew the wingnut.

How to tuck the line into the grass trimmer

Depending on the area of the lawn to be mowed, the grass trimmer is selected. Electric grass trimmer for small gardens or urban vegetable gardens, robotic lawnmower, gasoline mower or tractor mower for large lawns. We advise to make your choice according to your mowing area needs and your desire to relieve your labor with a self-propelled machine.

The trimmer is an indispensable addition to the trimmer, especially when it comes to mowing around trees or between rocks. Wire models have been proven to work efficiently. The motor-driven, high-speed rotating cutting head contains a spool of nylon thread. One or more strands come out of this head, which are stretched by centrifugal force and cut the grass like a blade.

Wire wound on a spool built into the rotary head has a diameter of 1.3 to 1.6 mm. Depending on brand and model, cutting head holds one or two threads. Double-layered cloth is on trend to save speed and reduce thread wear. Note that the nylon string wears out quickly if struck against stone or concrete edges.

How to change the trimmer line on a Ryobi 18 volt cordless string trimmer

The alternative to cassettes

The capacity of the spool determines how often the wire is refilled. For single drop tools, the spool contains 5-6 m of fishing line. For those with two wires, the length is usually two times 3 m.

  • The thread wears out when you cut it. It is replaced semi-automatically as soon as the cutting head hits the ground lightly. The strands come out if their end protrudes by a few centimeters (at first, the clipper blade automatically shortens them to the right length).
  • Most manufacturers offer replaceable cassettes to their users. They are expensive, and the empty spool and its accessories go in the trash. It is more economical to charge the spool with wire bought in a roll (about 2 euros per 15 m) in a garden center.

Choose the same diameter of wire

This cassette has a plastic spool on the bottom, a push button to release the wire, and a flexible ring with two diametrically opposed slots. This ring holds the nylon fishing line in place, allowing the two cutting edges to emerge.

Always follow the diameter specified by the manufacturer. The wire (Ø 1.3 mm in our example) is bent in the middle like a stud and inserted into the two holes next to one cheek of the spool. This double wire is wound in continuous turns clockwise. The flexible ring is pre-positioned, as soon as the winding is finished, one of the threads goes into the slot and the other comes out of the second slot. The ring gracefully closes the coil.

Preparing to wind the line

The line spool must be removed from the body before the winding process. Depending on the manufacturer, power and type (electric or gasoline), there are three design types of trimmers:

In this kind of model it is possible to install a knife. To remove the spool on these models, you need to use the two recessed buttons on the spool body. To install the trimmer blade, you need to align the hole of the bobbin and the rod, and then insert a device in the form of a steel pin (screwdriver, iron bar). After fixing the spool body can be easily unscrewed by hand in a clockwise direction.

How to change a line on a trimmer

Below we have given step by step instructions on how to change the grass trimmer filament.

The first thing to do is to disconnect the tool from the mains and turn off the motor. Then it is necessary to remove the grass trimmer head. This can be done by using a simple screwdriver into the hole in the gearbox to prevent the shaft from turning. And then simply unscrew

Unscrew usually clockwise, but different models have different mechanisms, so you may have to twist in the opposite direction. But if for some reason you can’t figure it out, then we highly recommend referring to the user manual to understand how to disconnect it

Second. After removing the mowing head you need to open it. This can be done by using the ratchets which are opposite each other. Pressing them, you can remove the cap of the head, and then pull out of it the spool, on which the line is wound. Taking it out, you can determine what type it belongs to. There are one-section and two-section bobbins

See also  How to choose a gasoline grass trimmer for mowing

We analyze how to tuck the fishing line into the grass trimmer spool in two variants

So, option one is to load the line into the single section reel. Prepared piece of thread is folded in half and slipped into the bobbin. Then, start winding both ends in the same direction, which will be indicated by an arrow on the bobbin. At the end of the bobbin winding do not forget to make sure that the different ends of the thread look in different directions

Option two is winding the line on a two-section bobbin. The previously prepared line is divided into two parts, and the ends must be secured by placing them in special brackets

Winding is done as in the first case by the arrow indicated on the bobbin. Both pieces of line should be wound so that they do not overlap. Next, the ends of the line should be secured in the slots and spread on opposite sides

The spring is then inserted into the coil, and the whole thing is placed in the mowing head. Putting the spool in the grass trimmer you need to carefully hold the spring in parallel, inserting the line into the slots in the head of the brushcutter. And finally, this just needs to be secured with the final part, that is, the cap.

After you have threaded the grass trimmer, you need to check it. If you got it right, it will work, but if you got it wrong, we suggest you read the article again, or better yet, watch the video on how to install the line on the spool in your trimmer.

How to get the line out of the weed trimmer reel

Over time, the cutting element of the head wears out, and it becomes necessary to pull out the remains of the old fishing line. Not everyone knows how to do it. Our step-by-step instructions plus a video of how to take the thread out of the grass trimmer spool, which you can find on the network, will help in solving this issue

You need to disassemble the mowing head

Difficult ? Certainly not. But if you still have doubts that you for some reason you can not do it, then of course find and watch the video how to pull out or how to wind the thread on the spool of a string trimmer.

What is the best line for a grass trimmer??

The speed of the electric and brushcutter is largely influenced by the quality of the line. On how properly it is wound on the mowing reel depends on the consumption of the cord itself, as well as the load that affects the engine. In this regard, every gardener needs to carefully study the rules of selecting and installing the line on the spool itself. This will prevent premature breakdown of the grass trimmer and make its operation on the garden plot more convenient and efficient.

Preliminary preparation

First of all, winding the fishing line requires removing the spool (bobbin, bobbin) from the grass trimmer. the specific steps will depend on the complexity of the configuration and type of the product itself:

  • Small electric grass trimmers with the motor and spool working at the bottom usually have side keys on either side of the reel. When they are pressed simultaneously, the upper part of the spool with the internal contents for winding the line is disconnected, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring which is part of the construction does not pop out and get lost;
  • electric and petrol grass trimmers with a curved boom without the possibility of installing a knife usually have a reel with a special wing nut: in such designs you should hold the bobbin in a stationary position with one hand, and with the other counterclockwise rotate the fixing bobbin on the boom wing nut. After undoing the nut the entire bobbin is removed.
  • electric and gasoline grass trimmers with the possibility of installing a knife on a straight bar (e.g. STIHL grass trimmers) have a hole under the reel. To immobilize the boom, a screwdriver or other suitable object is inserted into this hole and slowly rotating the screwdriver into the hole achieves a mutual position where the screwdriver enters and the reel is locked. The spool body is then turned clockwise (for left-hand thread) and removed from the grass trimmer.

For the second and third case, the reels, depending on the design, are disassembled in different ways. For spools with a wingnut, the wingnut is unscrewed, and for spools with latches, the latches are pressed and one part of the spool is released from the other part. If the bobbin halves are connected by thread, it is enough to turn them by hand in opposite directions until they are completely uncoupled.

Types of lines for grass trimmer

In the first place, in order not to resort to frequent changes, it is better to use a thicker line. The number of its types and manufacturers simply amazes. The main parameter of the line for grass trimmer is its diameter. It varies from 1.6 to 3.2 mm. The most common type is a 2-millimeter line. However, its selection must be made depending on the type of grass trimmer you have.

There are several different cross-sectional variations. So, it can be round, square, in the form of a star with sharp edges. The most effective is the last option. However, it should only be used on powerful mowers, and you need to know how to tuck the fishing line into the grass trimmer reel. Therefore, we can conclude that the more powerful your lawnmower, the thicker the line should be.

The process of winding a line on a grass trimmer is not complicated, but it does have its peculiarities. First of all, it is necessary to choose the right line, the diameter of which is prescribed in the certificate of the device.

First unscrew the coil cap. Be careful, because the thread can be either left or right. The left-hand thread is necessary to prevent the grasshopper head from unscrewing during operation.

Related Posts

| Denial of responsibility | Contacts |RSS