How to trim a ceiling plinth correctly

How to cut a ceiling plinth without a jigsaw

The factory chair. is an aluminum, plastic, or wood tray with a 45 0 or 90 0 dimple. Such a device is rarely used at home, so it is not common. But how to cut the ceiling plinths without a plank, also not many people know, so let’s consider a few simple solutions that allow you to dock ceiling plinths with great accuracy in the corners of the room.

When renovating an apartment, installing a new ceiling is often necessary to create a finished design idea. The completed ceiling is decorated with beautiful skirting boards. Baguettes are glued, nailed or screwed on the perimeter of the room, their position is pre-marked in the corners at the joints of the walls and ceiling. Cornices for ceilings are often rigid and hard slats (although there are elastic silicone ones), so they need to be nicely docked in the corners of the room with each other, and without a joiner this is difficult to do, but possible.

Corners of the ceiling are made of PVC, polystyrene foam (PPU), polyurethane (PU), polystyrene (PS), foam plastic (PP), wood or metal:

  • Styrofoam decorative ledge is fragile, but for unloaded ceiling designs it does not play a role. Skirting boards made of PP can have different width, the standard length. 1 meter, the surface. a bas-relief with different patterns;
  • Styrofoam is a dense material, easy to install, the edges of the cornice when cutting does not crumble;
  • Aluminium or wood is the most difficult to join. you need great accuracy, which is difficult to achieve without the use of a plier. To trim the corners of such eaves is recommended to use a blade on metal, to calculate the correct angle of trimming to use the following techniques.

Polyvinyl chloride is easily crumpled, after which it cannot be repaired. When machining requires caution and minimum pressure force

Can be cut with a joiner’s cutter or metal saw

Skirting board made of foam is fragile, easily crumbling. It is recommended to cut PP skirting boards with a very sharp cutter or a special tool. an electric nichrome cutter

Cut with a joiner’s cutter or metal hacksaw, hot wire clamped in clamps

Cut with a regular hand or special tools (an electric end saw, a fine-toothed wood saw, a metal blade), the cost of products is higher than that of PVC, PP OR PVC skirting boards

How to cut a skirting board properly

This is the perfect ceiling plinth you can make with your own hands, if you follow these instructions.

There are mainly three materials used to make ceiling cornices, these are:

Stucco ceiling mouldings are also made, but that’s another topic.

  • The most unstable and cheapest of them is Styrofoam, although the strength on the ceiling is not very much needed.
  • Styrofoam is much denser, can be easily cut with a knife and is of course more expensive.
  • Wood is the hardest to work with. In order for the corners of wooden baseboards to be perfect, it is necessary to use only a fine-toothed hacksaw, or even better a hacksaw for metal and a sanding sandpaper. Only in this case it is possible to achieve an even angle

How to properly cut the ceiling skirting with his own hands

Sometimes those who make repairs, asking themselves the question “What is the name of the ceiling skirting??” There are many names for this material. This is a fillet, and baguette, and cornice, and the frieze. Regardless of the name, the installation technology is not much different.Ceiling plinth is not only a decorative element that visually divides the walls and ceiling, it also has the ability to hide the joints of finishing materials ceiling and walls.

How to cut a ceiling plinth properly

This is the perfect ceiling plinth you can make with your own hands, if you follow these instructions.

There are mainly three materials used to make ceiling cornices, these are:

Stucco ceiling mouldings are also made, but that’s another topic.

  • The most unstable and cheapest of them is foam, although the strength on the ceiling is not very necessary.
  • Styrofoam is much denser, it can be easily cut with a knife and, of course, it is more expensive.
  • Wood is the hardest to work with. In order for the corners of wooden baseboards were perfect, you must use only a fine-toothed hacksaw, or better yet a hacksaw for metal and sandpaper. Only in this case it is possible to achieve an even angle

Trimming the ceiling skirting with their own hands

Let’s review step by step how to properly cut the corners of the skirting boards (also called a tile). In the vast majority of modern apartments, the corners of rooms and other rooms are 90 °. Cut the ceiling skirting must be at an angle of 45 ° or 90 °. How to cut a ceiling plinth? To do this, a special tool is used, which is called a plier. This tool already features 45° and 90° slots. At first glance it seems a simple task to cut the skirting board. But the fact is that he glued to the ceiling at an angle of 38 ° to 45 °, which means that the cut corners will not join, leaving gaps. To avoid this happens, and use a wire cutter.

Cut inner corners with a wire cutter

For this you will need the following tools:

  • Tack is placed on the bottom of the chair with the side that will be glued to the ceiling, and the underside is pressed against the wall of the chair, to its right slit.
  • Trimming the fillet is done with a hacksaw or sharp knife. It is necessary to cut accurately, without excessive force, so as not to deform the ceiling cornice and not to appear chips.
  • In the same way we cut the adjacent corner of the skirting board, but with the left slot on the jigsaw.
  • Then these parts are attached to the corner to check if there is a gap, you can trim with a knife.

Tip.In order not to transfer the material in vain and acquire skills, practice on small pieces first.

How to properly lay the baseboard in the chair

Cut the outer corners with a mitre saw

  • Put the skirting board at the corner, and mark the place on the skirting board where the outer corner begins with a pencil.
  • Then fit the skirting board into the mortise. The side that will be fastened to the ceiling, laid on the bottom of the chair, and the other side pressed against the wall.The mark on the skirting board should be near the left-hand slot. Cut one edge.
  • Then cut the other half of the corner in the same way. Only the mark on the skirting board must be near the right-hand slit.
See also  How to use a wood sander

Put both halves on the corner and check if there is a gap. If everything is OK, you can glue the skirting board in place.

How to cut an overhead skirting board without a mitre cutter Cut a skirting board for the inside corner

If you don’t have a joiner, you can do without one:

  • To do this, lay the skirting board against the ceiling the way it should stand, and run a fishing line along the ceiling.
  • Then put the skirting board to the ceiling to the right of the corner and run the second fishing line.
  • In that place where the scythe line crossed, we make a mark on a plinth and we spend a line from a mark to the bottom corner of a plinth. This fishing line will be the baseboard trim line.

The marking for trimming the left corner of the baseboard

Repeat the same procedure for the left-hand corner. Trim strictly along the lines with a sharp knife.Then we put it to the corner and check if there is a gap. If there is a gap, carefully trim the corners. After that the skirting board can be glued in place.

Tip. Do not use much force when trimming the skirting boards. It can crumple and deform after you stick it in place after the glue dries.

Marking for trimming the right-hand corner of the skirting board without a joiner

trim, ceiling, plinth, correctly

You can easily trim the deburring for the outside corner as well without a jigsaw:

  • For this purpose we put a ceiling strip as it should stand to the right from a corner. Guide the fishing line with a pencil on the ceiling beyond the corner.
  • Then attach the fillet to the left of the corner and run the fishing line along the ceiling until it intersects with the first line.
  • On the fillet make a mark at the intersection of the lines and in the place where the corner of the room.
  • Connect the marks with a line on the fillet and cut with a sharp knife. The cut should go inward of the fillet.
  • Check the joint at a corner, trim it if necessary, and glue the tack in place.

It should be noted that for 1 running meter. Count the number of meters in your apartment, multiply by 100. This will be the amount you will save if you do this work with your own hands.

How to cut a ceiling plinth in the corners: evenly with handy materials

Skirting boards for ceilings cut in different ways, but professionals use a plier. It is a carpentry device, which is a tray with slots on the sides. In them insert a hacksaw, and at the bottom of the tray put a board, batten, baseboard and other materials that need to saw at a certain angle.

Finishing finishing work in the house, many homeowners are faced with the problem of cutting the ceiling skirting boards, especially their corners. After all, it is on them that the attractiveness of the interior depends. Without these decorative elements, rooms would have an unfinished look. Guess how to cut the ceiling plinth with an angle, a metal ruler or flat bar, it is not difficult, because you only need to maintain a right angle.

But in finishing works requires trimming of baseboards and at other angles, such as 40 degrees. Therefore, the installation of these plastic elements is fraught with certain difficulties. To get the right angle, you need to be extremely careful. One of the problems is to cut the ceiling plinth in the corners with further docking.

In the manufacture of baseboards, the following materials are used:

  • Wood. Wood is considered the most labor-intensive material for processing. Wooden skirting boards are sawn with a joiner’s hacksaw.
  • Extruded polystyrene foam. Finishing material of high density. Does not absorb moisture. Does not emit any toxic substances when burned. It is rather difficult to work with, but easy to cut. All you need is a carpentry knife.
  • Styrofoam. It is fragile, the cheapest and easily workable material. Its brittleness is not a disadvantage, because the skirting boards are located under the ceiling itself, and they are not afraid of mechanical effects. It is easy to cut a skirting board out of Styrofoam.
  • Polyurethane. Characterized by plasticity and flexibility. Due to these properties, it is used on uneven surfaces. It is water repellent and resistant to temperature changes.
  • Polychlorvinyl. Difficult material to fit because of its high rigidity. Manufacturers offer it in different finishes: imitation of stone, metal, wood and even coloring. Becomes brittle in the cold.

Decorative elements made of aluminum look no less attractive under the ceiling. It is true to process and cut the metal is much more difficult than the materials from the suggested list. Increased demand for aluminum skirting boards is due to the fact that they are cable channels, which is convenient to hide wiring and cables. Aesthetics, not reacting to aggressive environments and detergents is not unimportant.

Cut an aluminum ceiling plinth with a metal hacksaw. In order not to break the cloth, reciprocating movements must be smooth and even.

Regardless of the material of manufacture, ceiling skirting boards can be considered the best solution to create a unique interior. They are mounted on the most difficult area, which is the junction of the wall and ceiling. Someone who knows how to properly cut the corner on the ceiling plinth, will quickly make the interior of the room complete, which will give it more appealing. With these elements you can partially cover minor defects.

The tool for cutting choose depending on the material and the necessary angles. In rooms of standard shapes with perfectly flat walls and ceilings, to cut the corners of the ceiling plinth use a plier. Wood is sawn with an ordinary carpentry saw, and for other materials, you should buy a jigsaw. You can also use a metal saw. To adjust the corners manually, you will need additional tools: ruler, angle, protractor, pencil.

Trimming a ceiling skirting board with a wire cutter

Work with this device is performed as follows:

  • We fix the jig on the workbench, put the decorative element in the tray and press it to the bottom and to one of the walls. Only then can you properly cut a corner on the ceiling plinth.
  • The wood is sawn using an ordinary hacksaw. Insert it in those slots, thanks to which you get the desired angle. Hold the cutting tool perpendicular to the element to be cut. The inner, as well as the outer corner of the ceiling plinth cut also with the help of a power tool.
  • It is better to use a carpentry knife or a jigsaw to cut a skirting board out of expanded polystyrene.
  • It is not recommended to use force when cutting. The blade must move smoothly, otherwise you can damage the decor or completely deform the product. Styrofoam skirting boards are cut with a jigsaw with the smallest teeth. A knife is not suitable for this work, as the material will crumple and crumble.

Correctly cut a ceiling plinth, where non-standard angles are required, is quite difficult. This is not what the power drill is designed for. If there is no skill, then the products may remain dents. They are finished with putty, and then painted in the desired color.

The main difficulty is that when cutting must maintain the required angle, otherwise when closing the two skirting boards, between them will be visible obvious gap. Many owners do not even pay any attention to this and absolutely do not get upset. They just putty and paint all the gaps. And since the exact shade of paint is difficult to choose, then the whole atmosphere in the room will be overshadowed by the aesthetic appearance of decorative elements.

See also  How to use a mowing for grass. How much time can a trimmer mowed for grass

Here is a video on how to cut corners on ceiling plinths. Cutting using a template allows you to make a clear end without the slightest deviation. Processing of decorative elements without a chisel is also possible, but on condition that one has some skill and knows how to use other auxiliary tools: squares and protractor. Using them, it will not be difficult to trim ceiling plinth with non-standard corners.

By the way, the jig can be made by yourself at home. You need three identical boards, 15 cm wide, approximately 50 cm long and 1-2 cm wide. The last two parameters do not have special importance, so they can be chosen at random. From these parts we make a tray. It resembles a box without ends and a lid. Then, using a protractor, mark the necessary angles on the side planks with a pencil. Then, according to these marks with a hacksaw make cuts all the way down to the base. Cut through two planks at the same time.

You should know the angle at which to cut the ceiling plinth, so in the planks of the plank saw, make these angles.

If you can’t make one, use another method. In this case you will need a hard cardboard. from which you can cut the template with the necessary angles. For this work you will also need a protractor. If you need 45 and 90 degree angles, you can use a regular angle piece. This is much easier and faster than constructing a jig. You take the cardboard, mark and cut out the template of the desired shape. Now all that remains is to put it on the baseboard, leave a pencil stripe on it and cut the ceiling skirting at 45 degrees.

Professional craftsmen begin installing decorative elements from the corners, and then proceed to installing baseboards in straight sections. Here is a video on how to cut ceiling plinths in the corners, as well as ways to install them.

потолочный плинтус- правильно режем в стусле

These products are the final finishing elements. They serve to clad the joints between ceilings and walls. In addition to the fact that with their help they disguise the roughly made junction, they perfectly harmonize with any style. The wider the skirting, the more streamlined the interior looks. For stretch ceilings, such decorative elements are a must. They perfectly conceal the mounting gap between the wall and the frame.

Perhaps from this article you have understood how to properly join a ceiling plinth in the corners and than fasten it on straight sections. When choosing such products, are guided by a simple rule: the higher the walls, the wider the baseboard must be. However, the wider, more irregular and harder it is, the harder it is to cut. Therefore, for such work it is necessary to prepare absolutely sharp cutting tools. You can try them out on scraps of decorative elements. It will be a kind of training, which will avoid unnecessary pressure in the work. As you know, it leaves indentations in polyurethane and PVC, chips peel off the wood, and the foam crumbles.

Colors and decorations depend on the style of the room. A huge variety of widths, textures and colors, makes it possible to choose the best option for a country house or apartment. When installing these elements, the main thing is to cut them correctly. See the photo, how to cut the corner on the ceiling plinth and you can do the job yourself.

Cut and fasten the product in the corners in the case when the fragment of the strip, cut at the desired angle, is already prepared for fastening, as well as joint with him a decorative element. If when cutting the skirting board the inner corner is not accurate, then you can ignore this. The main thing is to have a clear joint on the front side. It is not recommended to fix the joints to the paint. The best way to do this is to use rough plaster.

To summarize, you can cut the ceiling plinths without using specialists. The main thing to be careful and do the work thoughtfully and without fuss.

  • Your sky
  • Potolki812
  • Potolki-House
  • Leningrad windows and ceilings
  • Potolki-help
  • Alliance Ceiling
  • Ultra-thin LED light fixture 801.00
  • Round Energy Saving LED Ceiling Panel 10039.50
  • Environmentally friendly 15 volt energy saving ceiling lamp 4858.20
  • Rotating LED bulb for the club 279.90
  • Modern LED light bulb for the home 1525.50
  • LED lamp replacement for CFL devices 4774.50

At first glance, the installation of ceiling plinth seems quite simple task. Certainly, it is, if you have even the slightest experience of gluing baguettes. Those who first took up this business, already at the beginning of the process ask the question: how to properly cut corners from the ceiling plinth?

Modern devices for cutting skirting are mostly helpful when the wall surface is flat, without convexity, and the angle of the junction of the ceiling and wall is 90. But how to properly cut a ceiling plinth to form an even angle, if the surface is far from ideal? Many masters have come up with their own little tricks for coping with such a task. Some experienced professionals use for the cutting of ceiling skirting a simple board with a marking of the corner at 450 and cut it with a simple office knife or hacksaw for metal, while others use special devices, which are more easy to cope with the cutting of skirting boards before gluing.

In our master class, we will show you how to correctly cut a ceiling plinth to get a beautiful and even corner. Many first-timers take a lot of effort and time, but in the end the result is a pleasant delight.

And so, in order to cut the corner from the ceiling plinth we will need:

How to properly cut the ceiling plinth to get an even corner?

Now that we are all even and accurately docked, you can proceed to gluing and painting ceiling skirting boards. It is worth taking into account the fact that you will often have to trim the skirting, so when you calculate the number of panels of mouldings, keep in mind that you will have to cut them.

How to evenly cut the corner of the ceiling plinth When we evaluate a new repair, we involuntarily stare,

How to cut in a wall to ceiling line, how to paint a straight line when cutting in.

How to properly trim a ceiling plinth This is what properly trimmed ceiling plinth corners look like This is the perfect

How to evenly cut the corner of the ceiling plinth When we evaluate a new repair, we involuntarily stare,

How to cut a ceiling plinth Cutting ceiling plinth in the jigsaw How to cut a ceiling plinth to match

How to cut a skirting board without a joiner

Trimming the skirting board for the inside corner

If you don’t have a joiner, you can do without it:

  • To do this we put the skirting board on the ceiling the way it should stand, and run a fishing line along the ceiling.
  • Then we put the skirting board to the ceiling to the right of the corner and run the second line.
  • In the place where the scythe line crosses, make a mark on the skirting board and guide the line from the mark to the bottom corner of the skirting board. This line will be the baseboard trim line.

Mark the left-hand corner of the skirting board for trimming

See also  Lawn mower won't start on hot run. Maintaining the chain saw correctly

Система выносного монтажа: зачем нужна? Скептикам смотреть обязательно! // FORUMHOUSE

Do the same with the left corner. Cut straight along the lines with a sharp knife.Then fit it to the corner and check if there is a gap. If there is a gap, carefully trim the corners. The skirting board can then be glued in place.

Tip. Do not use excessive force when trimming the baseboard. It can crumple and deform after you glue it in place after the glue dries.

Marking for trimming the right corner of the baseboard without a mortar

Trim the skirting board for the outside corner

It is easy to cut the fillet for the outer corner without a joiner:

  • To do this, apply the ceiling finish as it should be to the right of the corner. Lead the line with a pencil on the ceiling beyond the corner.
  • Then put the tack left of the corner and run the fishing line across the ceiling until it intersects with the first line.
  • On the baseboard make a mark at the intersection of the lines and where the corner of the room.
  • Connect the marks with a line on the fillet and cut with a sharp knife. The cut should extend inward from the fillet.
  • Check the corner joint, trim it if necessary, and glue the trim in place.

it should be noted that per linear meter. Count the number of meters in your apartment, multiply by 100. This will be the amount you save if you do the job yourself.

How to cut ceiling skirting boards in the corners?

Do you want to know how to cut a skirting board in the corners?? The first thing you need to know when cutting ceiling plinths in the corners is the properties of the material that was used in finishing the ceiling. If the skirting boards in the corner of the foam, technically cutting will not be too difficult, but you must also take into account its fragility. Extruded polystyrene foam will require a chisel and other carpentry tools, as the material is really poorly machinable, but the result is visually pleasing. It is also better to cut wooden elements strictly professionally, otherwise there is a risk of spoiling the previous repair work.

What tools can be used?

The appropriateness of using these or those tools is related to the materials of which the baseboard will be made.

Table. 1. Varieties of materials and peculiarities of their use.

Type of material Material properties, requirements Tool
Polyvinyl chloride (PVC) PVC skirting boards are notorious for being easily damaged when pressed and no longer recover their former appearance, as they lack elasticity. This is why these skirting boards cannot be pressed when cut. Cut with a construction knife or a metal saw. Suitable also a blade or a sharpened kitchen knife.
Styrofoam Plastic skirting boards are also not very durable, but they are better than their PVC counterparts. They crumble easily. Can use the same tools as for PVC
Wood Stronger and more aesthetic than their polymeric counterparts, but expensive. Wood is best cut with a hacksaw, or metal, although you risk clogging the teeth with wood shavings. A fine toothed wood hacksaw is best.

Technology of cutting ceiling skirting boards

For quick and quality work it is necessary to choose the tool according to the material of the skirting boards and select the method of cutting. If you have a crosshair, then there will be no special difficulties in the process. If it does not exist, then you have two options: to cut according to the template and measurements on the ceiling, or to make this tool yourself.

Peculiarities of cutting ceiling plinths in the jigsaw

Work with this device must be very carefully so as not to blunt the tool and not to leave cuts in unnecessary places. In the process, follow the following instructions:

    Fix the baguette in the jig the way you plan to place it on the wall. The side that will be pressed to the ceiling on the jig, must be adjacent to the sidewall.

Techniques for cutting ceiling skirting boards by the template

This method can be used if your corners. even, and you need to trim the baguette exactly 45 degrees. To do this, before you cut the ceiling molding in the corners, you need to draw a jig on heavy paper. We draw two parallel mowing lines and mark the angles at the desired degrees, using a protractor.

We place the baseboard in this case in the same way as with a traditional jigsaw. Keep in mind, that the instrument should be kept in vertical position when cutting the skirting boards.

Rules of cutting ceiling plinths according to the marking

This method is used to cut the baseboard in cases where there is no jigsaw, or parts from which it can be made.

To do this, you need to make a marking on the wall in this order:

    We put a baguette in a corner to the place of fastening.

How to cut a ceiling plinth without a joiner

To accurately dock in the inner corners of the fillets, you can do without a jigsaw.

    We bring the end part of the baguette to a sheet of paper and trace the contour of the convex side. It is more convenient to use a small section of a skirting board (if you have one).

Tools required

Installing the ceiling plinth involves trimming the excess length and adjusting it in the corners. In order to make a trim, you need tools. The choice of one tool or another depends on the material of which the skirting board is made.

When working with wood and plastic use an electric mitre saw. Trimming with the use of this tool is accurate, fast and without much effort, it is only necessary to set the right parameters and properly lay the plinth. To pick up the appropriate tool will not be difficult, thankfully the manufacturers produce this tool in a wide price range.

But, with wood and plastic you can also cope with another well-known carpentry tool. a pliers paired with a hacksaw. This tool is shaped like a tray and is made of either wood, plastic or metal. In the two parallel sides of the baseboard cutter there are slots for the saw, for easy trimming of the baseboard at the right angle. With a simple modification, you can cut the ceiling element at an angle of 45 or 90 degrees, and with the more complex version, you can also cut the skirting at an angle of 60 degrees.

A chisel and a hacksaw are less expensive than a mitre saw, but they also have their own drawback. the risk of damaging the material, especially if the quality of the purchased material leaves much to be desired. Also, the mitre saw is best suited for even walls and angles.

For a cleaner cut without damaging the material and without splitting the structure, the jigsaw is the right choice. This tool is easy to operate, it can be used to set any direction and make the most accurate cuts. For lighter materials and materials with a less strong structure, you can use an ordinary construction knife, the main thing is to choose a copy with a sharp blade.

Related Posts

| Denial of responsibility | Contacts |RSS