How to start the STIHL 180 chain saw

STIHL chain saw carburetor adjustment

It is used if the saw stops when you press the throttle. You first clean the carburettor, change the spark plug and clean the filter. Control the engine at idling speed.

Adjusting the carburetor on a STIHL chain saw

  • You should first turn off the power tool and turn the two screws L and H as far as they go.
  • The same screws are turned by one turn.
  • Starts the tool, warms up the engine.
  • Depress the throttle lever and turn the H screw until rpm stabilizes.
  • Turn the screw LA until the chain starts to run, after that turn it a quarter of the way back.

After these steps your STIHL chain saw should be running. If there are still problems, you still have to work with the LA screw and turn it a bit more.

How to run-in the chain saw.

After a chain saw has been successfully started up, it’s time to start running it in. Starting with the manufacturer’s instructions. The procedure itself has two basic steps that allow you to lapping up the moving parts of the gasoline tool engine and saw headset assemblies. So let’s explain the steps in more detail.

Running-in of gasoline chainsaw engine.

Motors of imported gasoline saws are run-in with some differences from domestic units. Husqvarna, STIHL, Partner and others are not designed for continuous idle operation. That’s why after starting the engine of the chain saw let it work for about 3 5 minutes at idle speed, and then start cutting wood with a diameter not exceeding 10 cm at medium rpm. Sawing is best done in cyclic mode:

During running-in and operation, the thickness of the log has no influence on the load on the saw motor and the saw unit. The load is directly related to the amount of force the operator exerts during the sawing process.

Why it is not recommended to let the power unit idle during the break-in procedure of any imported chainsaw? The reason is this:

  • Insufficient fuel/air mixture in the cylinder at idle speed. It is only powerful enough to maintain the torque of the connecting rod and piston group. Why is there no proper lubrication of the cranking parts?
  • Lack of lubrication causes higher temperatures and increased wear.

Running in of home-made chainsaws “Ural” and “Druzhba” is fundamentally different. Developed in the USSR, the tool requires 3-4 tanks of fuel mixture at idle rpm with periodic regassing. Afterwards it is allowed to work part load for 24 hours according to the cyclic pattern above. That is why more oil is added to the fuel mixture than to the imported analogues.

As a rule, after working out 57 full tanks, the running-in tool of domestic and imported production comes out at full power, laid down by the manufacturer. During this period, you should not:

  • Overheating the engine;
  • Allow the chainsaw to idle for long periods of time;
  • Working at too high rpm;
  • Maximum loads during sawing.

How to Start a STIHL 180 Chainsaw Video

The STIHL mc 180 chain saw is a cross-cutting tool. The machine is classified as a domestic-use machine. Model differs from the professional tools working tools material and is designed for occasional use, not more than 40 minutes per cycle.

Types of saws and technical characteristics

The STIHL mc 180 chain saw is in demand among hobbyists because of its operating comfort and reliability. The basic model weighs only 3.9 kg. Sabre, the length of the blade 35 cm allows you to cut logs or drop trees up to 30 cm. Power of a 2 liter two-stroke motor. с., that allows you to do all household chores associated with crosscutting boards and even firewood in any type of tree. The fuel tank capacity is only 0.25 l, but it allows you to work non-stop for 45 to 55 minutes.

Use a mix of recommended or transmission oil with unleaded AI-92 and AI-95 gasoline for refueling. Proportion 25 ml additive per liter of gasoline.

STIHL chain saw chain for the STIHL 180 chain is a continuous chain with 50 links. Other features:

The chain lubrication system has a bar, a chain sprocket and an automatic oiling system.

NEW Chainsaw Stihl MS180 FIRSTART!

Chain tensioning system is located on the side, which is comfortable. Brake device for chain.

Depending on the length of the bar and modernization of chain saw STIHL MS 180 there is a number of modifications. Saws with a 35 cm blade length are referred to as models with a 14 in. The same configuration on the engine and its characteristics, but with a bar length of 40 cm, called the MC 180 16. The STIHL mc 180 C-BE is a high-end chain saw. It has a 40 cm long guide bar, easy start system and sharp chain tensioning system. Easy access to the air intake filter, a condition which extends the life of the tool.

See also  How to install a turtle on an angle grinder. Metal and wood sanding angle grinder accessory (bladed abrasive disc)

READ Chainsaw chain sharpening Limiter

Keeping to the instruction manual is essential for keeping the machine in working order

Every machine is provided with an instruction manual, especially the more complex STIHL chainsaw STIHL 180. Before you start the machine for the first time you need to know the technical controls. This is even more important if you already have experience with the Druzhba. Other assembly, the chain tensioning system, starting and tool adjustment conditions require preliminary acquaintance. There are reports on the forums that the sawyer poured the spark plug on the first start. repeatedly pulling the starter, it is necessary:

To avoid any problems, it is necessary to fill the tank completely and not to leave it to “sour” for several days.

This instruction manual provides a definition of the marking on the machine in words. There is also a parts line, the order of disassembly of chain saw STIHL 180 for replacement of components, sharpening the chain.

Warnings about how to work with high-risk tools, non-hazardous techniques will help avoid injury. Genuine STIHL 180 chainsaw video, Genuine STIHL 180, chainsaw overview video. When changing the chain it is important to check that it is recommended by the manufacturer. Unsuitable assemblies can lead to malfunctions, failure to meet warranty criteria.

STIHL MS 170, STIHL MS 180, STIHL MS 180 C-BE chainsaws

MS 170, STIHL MS 180, STIHL MS 180 C BE right here: STIHL MS 170

STIHL MS 180 chain saw Overview

MS-180 In this video we will look at STIHL chain saw (STIHL). Consider its equipment and

Do-it-yourself saw repair

The lightweight and handy STIHL MS 180 chain saw replaces a two-handed saw, bow saw and even a hacksaw in the home. Over time chains get dull, sprockets get worn and the oil system gets damaged. Some of the problems you can fix yourself. As with all STIHL chain saws, here is a video review of the STIHL STIHL 180 chain saw. 1. Others require repair at special service centers.

Check that the lubricant is in the oil reservoir and that it is flowing to the chain with a clean piece of paper. Direct the tire to a piece of paper, it should leave a characteristic mark in the form of an oily streak.

READ How to Adjust the Carburetor on a Huter Chainsaw

To repair your saw yourself, you need to understand the design of the assemblies and the sequence of operations for removing and repairing or replacing the assembly. STIHL chainsaw STIHL 180 Instruction Manual is a reliable companion. It is there that you can find the assembly techniques and the sequence of repair operations:

Even a home technician can shorten an overstretched chain and have it resharpened.

If your saw chain stays dry or leaks oil during operation, you need to troubleshoot and repair your STIHL 180 chain saw’s lubrication system. Check oil pipes and tightness of connections with connectors. The filter in the oil supply must be cleaned. If there is minor mechanical damage to the hoses, the tightness can be restored with sealant.

The carburetor makes itself known by the difficulty in starting the saw, the launched tool does not pick up speed, it throttles when throttling. The cause of the problem could be a worn collar on the piston that draws in air as it is depressurized. To repair the carburetor remove and get to the collar on the gas pedal, disassembling the unit in sequence:

  • Remove the diaphragm cover by removing the screw;
  • Remove the locking ring;
  • Disconnect the air damper, remove the throttle;
  • Pull out the gas pedal with the spring;
  • Replace the tiny piston and collar and assemble the carburetor in the reverse order.

Troubleshooting can be traced to the ignition system. After checking spark plugs and cleaning fouling, carburettor adjustment, feeding system adjustment and injection cleaning. The carburetor is a tricky part, and its adjustment affects how the chassis performs. If you are unsure and unskilled, it is best to use the services of a specialist. Low-quality gasoline and unsuitable oil are often the root cause of malfunctions.

You can find information on how to service a STIHL 180 chain saw yourself on the web sites to help the mechanic.

You can see about diagnosing the lubrication system here:

start, stihl, chain

Features of saw chains

Saw’s working mechanism is the chain. The chains are produced using a very special production process:

  • The cutting element is made of high-carbon steel, and the use of chrome plating or a pobedite layer on the cutter. The more complicated the manufacturing technology, the higher the cost of the chain.
  • Hinge bores are ground to reduce friction and extend service life.
  • Only specially hardened rivets are used.
  • Markings on the teeth are helpful in determining wear and sharpening.
  • After joining the links into the chain, the product must be stretched to ensure dimensional stability when working.

READ Repair of Gasoline Saw Ural Electron with Your Hands

Intelligent automatic chain lubrication system increases durability. New STIHL chain saws should be cut to the specifications in the instruction manual for the STIHL Miniature Saw 180.

Please note that carbide-tipped chains are up to 3 to 5 times more expensive than conventional ones, but it is not possible to sharpen them yourself when repairing the STIHL 180 chain saw. It is mainly used by emergency services staff.

STIHL chain saws are designed to run longer without wear and tear. A special mineral compound is used which prevents the chain from galling. STIHL chain saws should not be made with oil that is designed for additives in gasoline.

People often ask whether you can make longitudinal cuts with the STIHL 180. Watch a video review of the various chain saw malfunctions and possible solutions. Find out why your chainsaw won’t start. The power of the saw allows you to work in cross-cutting wood only.

See also  The chain on the chain saw does not tighten

STIHL saws are generally well reviewed. There are complaints about the insufficient power of the tool. You need to select the correct helper for the task at hand. The lightweight, affordable STIHL 180 chain saw is designed for occasional use. Special products are available for felling and chopping work. This is not a good idea for your home. The tool is much heavier, so it is not suitable for cutting small boards.

The STIHL MS 180 chain saw is priced very differently. The most inexpensive basic model. The cost of the tool varies depending on the country of manufacture. A German or American product is more expensive than a Chinese product for well-known reasons.

Operating principles

Always hold the chain saw with both hands and use both fingers to grip the handle firmly (the left thumb should be under the front handle). The saw should be placed closer to the body, so your arm muscles will be less fatigued (no need to fear the proximity of the saw). This position also makes it easier for you to hold your balance and keep full control.

To ensure stability, spread your legs wide apart with the knees bent, but keep your back straight. If the handyman needs to change position, he must first turn off the motor by activating the brake. If the chainsaw has to be carried a considerable distance, it is recommended that the guide bar is covered.

To learn how to use a chainsaw at first it is better to use horizontal, not too thick logs. When you feel confident and strong in your hands, you can learn how to fell trees. To saw logs or beams evenly, you must make pencil marks and then gradually move along these marks. It’s a good idea to watch experienced sawyers at work.

Preparation stage

Before you cut the tree you must make sure the surrounding environment (rails, buildings, power lines, highways etc.) cannot be damaged by the falling tree. There must not be anything within a two-length felling distance of the tree to be cut in either direction. In addition, if the place is crowded, warning signs must be used. this is a must.

This will ultimately determine in which direction the tree will fall. You have to be especially careful with rotten, dry wood. It can behave unpredictably for the logger and fall off not as planned. You can recognize a damaged tree by its outer appearance (dry branches, damaged trunk). Experienced woodcutters determine the quality of wood by tapping the trunk. a healthy tree “rings”, a diseased tree has a muffled sound or is not audible.

Как правильно заводить Штиль 180 видео, How to start Calm 180 video

start, stihl, chain

The ground around the tree must be cleared of bushes and other growth. this is another important preparatory action. Anything that can prevent the chain saw operator from leaving safely during the felling process must be removed

How to saw

The sawing procedure itself usually goes like this. The lumberjack stands to the right of the trunk and makes a 45-degree angle guide notch on the side of the natural incline to a depth of about a quarter of the tree’s diameter. Keep this felling notch as low as possible so it is easier to fell the tree (and also so the tree stump is not too high). It’s also worth bearing in mind that the undercut kind of indicates in which direction the tree will later fall to the ground.

On the opposite side of the tree a horizontal undercut is then made. the main felling cut. Some distance should be left between it and the slanting undercut. this clearance is necessary to prevent the tree from collapsing early.

While working, you need to watch where the tree is leaning so you have time to react if something goes wrong. When the tree starts to fall you need to remove the chainsaw from the cut quickly, turn off the engine and leave the danger spot.

If the tree is caught in another branch and doesn’t fall all the way down, you will need professional help. Never leave it unattended or try to correct it yourself.

There are times when a chainsaw bar gets stuck in a tree. There is no need to panic and abruptly pull it out, especially if the tool is in working order. The first thing to do is to stop the engine. And then you have to tilt the barrel manually, little by little, until the chainsaw slips out.

How to start a STIHL chain saw

STIHL equipment is high-performance, designed for gardening and manufacturing tasks. Germany is the manufacturer, and the company’s main production site is in Germany.

STIHL saws are one of the brand’s specialties. The range includes amateur, semi-professional and professional models. The tools are distinguished by their high performance, good quality and ergonomic design.

Below we will consider the model range of saws, as well as the solution to the main problems that arise during the use of the tool.

Specifications of the STIHL chain saw 180 ms

Features of the STIHL 180 ms chain saw:

  • power 1500 W;
  • 31.8 cc engine. see;
  • Idle speed is 2800 rpm;
  • maximum rpm is 9000;
  • guide bar 35 cm;
  • STIHL Oilomatic Picco Micro 3 chain;
  • 250 ml gasoline fuel tank;
  • chain pitch 3/8;
  • Noise level during operation 110 dB.

The STIHL chain saw 180 data sheet is the most important document containing all of the machine’s technical specifications. It tells you how to prepare the gasoline for your STIHL 180 chain saw, how to run it in, and how to service it.

See also  Nut jammed on angle grinder. Measures to avoid jamming

Topical question. how many links in a chain for the STIHL 180 chain saw. A STIHL original brand chain normally has 50 links, but if you use a chain from another brand, the number of links may be different, as it is the chain pitch that is important, i.e. the distance between the links, not the number of links.

STIHL chain saw MS 180

Getting the STIHL MS 180 C started

The device of this model, in comparison with the previous one, has some differences in the starting mechanism, but it does not bring any changes in the algorithm of starting. The reason is that the STIHL 180 C has an ErgoStart system which reduces the resistance of the engine when starting due to an additional spring in the starter bar.

Easy chainsaw start what it is

Why a priming pump is needed?When you press the priming pump, the fuel mixture is primed and fills the carburettor. Runs the engine faster without warming up. (A priming pump is included on the Patriot Garden 2512; 3816; 3818; 5518).

What is the difference between a nylon and felt air filter??The nylon filter, usually reusable, is easy to wash and clean when dirty, but it can be damaged by accidental ingestion of large sawdust. The felt filter is more resistant to mechanical damage, but cleaning it when dirty does not always give the desired results. (All Patriot Garden models have a nylon air filter).

What the number of cams on the clutch affects? cams provide a more reliable clutch, minimizing slippage. The load on the clutch cup is more evenly distributed. (All Patriot Garden models except 2512 have a 3-jaw clutch).

Why do you need a vibration protector??Sawing provides some vibration when the engine is running and the saw chain is in contact with the wood. The STIHL anti-vibration system greatly reduces the vibrations experienced by the machine operator. (All Patriot Garden models are equipped with vibration protection).

What is an adjustable oil pump?The oil pump setting affects the amount of lubricant applied to the guide bar. If you use different bar sizes on your chain saw, you need to optimise and adjust the lubricant flow, i.e. you can get the STIHL STIHL STIHL guide bar on the bar.The longer the bar is, the more lubrication is needed. When cutting different types of wood, it is also necessary to correct the amount of lubrication. (All Patriot Garden models except 5518 have an adjustable oil pump).

Why is there a small hole in the tip of the guide bar??Hole is for lubricating chain sprocket roller bearings. Т.к. The chain is under great strain during sawing and should be lubricated with a grease gun before starting to saw. Roller bearings can seize if not lubricated. (All Patriot Garden chain saws have a lubrication hole).

Why do I need the chain brake??There is a 90° section at the tip of the guide bar which causes the saw to rebound back toward the operator when sawing. To prevent injury, the centrifugal brake is automatically engaged by the right hand wrist during rebound. Mechanism triggers, saw chain stops instantly. (All Patriot Garden models are equipped with a chain brake).

What are the pluses of the chrome cylinder engine?Chrome plated for longer motor life, t.Chromium is a very durable material, resistant to high temperatures, and has good friction properties. Chromium plated cylinders are used extensively in power tools intended for professional use. (All Patriot Garden models have chrome cylinders).

What’s the difference between one and two piston rings in engine design?Engines with a single piston ring have faster acceleration and greater injectivity. Cylinder wear is slower due to the small contact area. But these engines are very sensitive to fuel quality. Engines with two piston rings have lower acceleration and acceleration than engines with one piston ring. Cylinder wear is faster due to increased contact area and higher friction. Lower fuel quality sensitivity. (All Patriot Garden engines except 2512; 3816; 3818 have dual piston rings).

What is Easy start??Chainsaws equipped with easy-start starters have a special mechanism with two cocking springs in their design. Significantly less force is required to pull the starter cord. The engine can be started much more easily. (Patriot Garden 3816; 3818; 4016; 4018 models have an easy start system).

STIHL 180 How to start a chainsaw. Starting the Stihl MS 180 chainsaw. Engine start stihl ms 180.

What else should our customer do? STIHL brand chain saws have a two-stroke engine. Their cool start is carried out by a similar method. But there are models on sale, which have additional equipment, thanks to its use it is possible to start the saw without much effort. Therefore the starting procedure may be different.

STIHL 250 chain saw review

Buy 250 models at a price of 29,542 rubles. This equipment is a semi-professional model with a 40 cm wide bus. Power is 3.1 liters. From. or 2.3 kW. Fuel tank capacity of 0.47 liters.

Quite often consumers ask themselves, before buying, how to start a Chill 250 chainsaw. This was discussed above. However, this is not the only information you should read before you start working with the model. Other features include:

Buy this model for quick fueling. This function is realized by the cover, which has a patented design. The operator working with the equipment will have reliable hand protection. Consumers especially distinguish the toothed fence, as well as the chain, which guarantees high-quality and fast cutting of wood.

Related Posts

| Denial of responsibility | Contacts |RSS