How to remove the housing of a brother sewing machine

How to tuck the thread into the sewing machine Brother: instructions and recommendations

Japanese company Brother is one of the largest manufacturers of sewing equipment. The company supplies high-quality devices for household and industrial use.

remove, housing, brother, sewing, machine

Proper threading is essential for sewing a product (

Before you start work, it is necessary to set up the machine correctly. To do this, you need to know how to thread the needle.

How to change the needle in a sewing machine brother: useful tips

When sewing, it is often necessary to change the needle on the machine. It can be blunt or bent, so change the needle immediately to prevent it from breaking or damaging the fabric. Another reason for changing a needle can be to use a special needle for a specific application. embroidery, decorative stitching. Replacing the needle is an easy procedure for most modern sewing machines.

When replacing the needle, proceed only step by step following the instructions (

Before you change the needle in the sewing machine brother, you need to study the instructions with a photo of the process, watch a video on the Internet and then follow the prescribed steps.

How to disassemble the sewing machine Brother? How to remove the lid of the sewing machine?

Did not say in the video, and you should have! Before you deflate with compressed air, what is undesirable there, I use a regular household vacuum cleaner for removal of pargas and ochos not sticking and not crumpled. And then at the same time and compressed air and vacuum cleaner on the pickup (why do I need all of it in the shop to disperse) Yes, and even by and large it is not screws and SAMORES !

Fanzilya Khalikova

Thank you very much. The machine is 6 years old, only today was able to disassemble and clean the poor

lina l

I have the same type of cover as you have in the video and also a Brazier, I did everything as you showed, and still cover does not separate somewhere near the main screw, where the bitch is fastening it is not clear!

maxdrive

This machine is considered a frame machine.And Brother HQ 22 frame or not?

972aida

Thank you very much! My husband twisted and turned, so he did not figure it out on his own, he says. it is not written in the manual))

Sasha Sasha Sasha

In the Brother machine reverse stopped working, can you adjust?

Lara Ptushkina

Sergei Yakovlevich, how often should preventive maintenance of the computer machine. ? I mean to give to the service center. I also have a Brother (sm-340e).Cleaned and lubricated only the shuttle.

Lida Trushevskaya

The plates of the upper tensioner came apart. (When scrolling the wheel is not stretched anything) has not disassembled yet, saw in the gap. I can fix it myself?

Alla Kowalska

I have the same machine only model HQ 27, unscrewed the screws as you show, but the machine does not split at the top near the wheel, almost crying. Tried to unscrew it more than once and no way, the machine has never for ten years did not lubricate, clean only in the bobbin department. Afraid to put the effort, what if I break something. The lower part is 1.5 cm apart. Maybe something advise? Thank you.

Needlework accessories

Hello. brazers rs20 shuttle did not reset the thread, I adjust, all the same tighten, after an hour, maybe even less upset may be a matter of the locking screw?

Lika K.

Hello, Sergei Yakovlevich. My Brother XR-36 began to make a loop from the bottom of the upper thread quite long. Seam beautiful, sews fine and then suddenly there is a click and a loop at the bottom, every time the gap is different and a meter can be a normal seam and 15 cm. Please advise what to look for the cause ?

dmitry khavlin

And the question. Flywheel here with a flat spring? If you can, please tell me about the flywheels of modern machines and how to assemble them properly. Because everything is clear on the PMZ and veritas, but with the new ones people have problems.

Svetlana Breeze.

Thank you very much. Disassembled and reassembled. It’s a pity in vain. Sew backwards and all. The same computer comfort 40e. Do not know what the problem is?

Tatiana Starikova

Hello Sergey Yakovlevich. Very pleased with your site. can you tell me what can cause wedge sewing machine Browser Tradition 2263 and how to remove the front panel.Cleaned and oiled the shuttle gear. I took off the back panel, between the brushes that move the cloth cleaned. The shaft is wedged anyway.Tell me what to look for. Thanks.

Oksana Demina

What do I do when the foot is down and the machine gives out an error E1

See also  What is the difference between a red Makita and a blue Makita

Izja Schnipperson

Very useful information for choosing a sewing machine! I do not buy one because it has a load-bearing body. All mechanisms are held in plastic. Maybe it’s okay, but I think it is not reliable. Thank you!

Vasily Razorenov

I just bought a 200 gram can of silicone grease (spray) Ermak for 200, I think that for these machines is enough. These greases have a lower yield from plastic.

Sequence of machine disassembly and lubrication

Disassembly of the machine is necessary before greasing. Looking at it, you can tell at a glance which parts can be removed and unscrewed. The general order of work is as follows:

  • Remove the needle bar cover by loosening the screw and pulling out the cover;
  • Turn the machine over and unscrew all the bolts at the bottom;
  • Pull back the speed selector knob and remove it;
  • Remove the cover from the side without touching the flywheel;
  • Unscrew all remaining screws;
  • Remove the handle fasteners;
  • Pull the foot controller downward;
  • Disconnect the remnants of the plastic body;
  • Take the hook out of the holder.

You will be interested in step by step instructions for sewing cushions on chairs and stools

The machine in disassembled condition

No further disassembly is necessary. All components can be reached with your hands or a syringe. Further order of unit lubrication is as follows:

  • Position the machine as if it were going to be used for sewing;
  • Fill a syringe with grease;
  • Slowly turn the flywheel counterclockwise;
  • Drop oil on all available parts and their joints, which will begin translational and rotational motion;

Dropping from the top

  • Never touch plastic parts and gears that have already been lubricated with a special compound, as it can damage them;
  • Lubricate the parts of the needle bar in the friction points;
  • Remove excess grease with a cloth or rag;
  • Check the course of the nodes by connecting the power;
  • Assemble the machine and give it a couple of hours to allow the connections of the parts to soak in oil;
  • Run for a couple of minutes with the presser foot raised.

Drenching from above

How to grease a Janome sewing machine

Janome. popular machines, so the question is relevant. As with any machine, they need regular preventive maintenance and lubrication. At least the main parts that drive the unit should be treated.

Before working, it is important to read the instructions for cleaning and operation, consider all the explanatory drawings. It is necessary to remove the lid of the device and pour the grease into the special holes and apply it to the rubbing elements.

Janome Sewist 780D

Lubrication of the Brother machine

No less popular brand of machines. It has its own instructions for it, but if it is lost, it is important to remind that a couple of drops of oil will be enough for treatment. Apply them only to metal surfaces, avoiding lubrication of the plastic.

Important! Brazier especially needs quality wiping off excess oil after machining, as well as idling for consumption mechanisms.

Removing the shuttle from Brazier

Singer

Quality Singer machines need lubrication much less often, but still require maintenance. Cleaning them should start with the needle plate. To do this, the screws are unscrewed and cleaned. Next, the shuttle is cleaned: the cap is taken out, and the latches are pulled apart. The shuttle parts are taken out and cleaned of dust. The same is done with the rotating device itself.

Astralux

  • Remove the needle plate by turning the handwheel until the needle is in its upper position;
  • Clean the lower cloth conveyor. To do this, take out the bobbin cap and use a brush to clean the conveyor belt;
  • Clean gears and grease them. Take out the bobbin and cap and swing the two holders to the sides. When this is done, the hook will come out freely and you can lubricate the unit;
  • Replace the bobbin and cap by turning the handwheel.

You will be interested in How to line up a pattern of men’s pants

Astralux needs to lubricate the roller

Machines with vertical shuttles

They are particularly in need of lubrication, even imported ones. The steps are the same: Remove the bobbin and pull the catches apart, take out the shuttle parts and wipe them thoroughly. Put everything back in. With these machines, it is important that the needle bar is in the up position.

Horizontal hook machines

Most of these machines have a lube-free shuttle, but this is a ploy to sell new machinery when the old one breaks down due to improper operation. Every moving mechanism needs lubrication.

Electric Brazier Artwork with horizontal hook

Rotary hook machines

This type of shuttle is the most reliable and lasts the longest. This is the most reliable, safest, and longest lasting sewing hook. This is due to its popularity in industrial machines. For long life, it must be cleaned and dripped with three drops of oil.

Proper care for your sewing machine

In order to ensure that every time before using the sewing machine does not require its adjustment, it is enough to observe certain preventive measures, the main ones include:

  • All main parts should be lubricated with a special oil at least once every six months;
  • after each use of the sewing machine is necessary to remove all dust and dirt from its surface, as well as the cover of the hook and needle plate, formed during operation;
  • Before you hide the machine in the cover, make sure that there are no torn threads and fabric in its structural elements, as well as putting a thick paper or cardboard under the foot, put it down to the stop;
  • storage of the sewing machine should be carried out in a cover;
  • Pedal and drive cords should be coiled as carefully as possible to avoid kinking and rips.
See also  The cable stripping tool with your own hands

You can also read. How to properly thread, needle or bobbin in the sewing machine.

Disassembly and lubrication sequence of the machine

Disassembly of the machine is necessary before lubrication. By looking at it, you can immediately identify the elements that can be removed and unscrewed. The general order of work is as follows:

  • Remove the shroud from the needle bar by loosening the screw and pulling the shroud out;
  • Turn the unit over and unscrew all the bolts at the bottom;
  • Pull off the speed selector knob and remove it;
  • Remove the cover from the side without touching the flywheel;
  • Unscrew all remaining screws;
  • Remove the handle fasteners;
  • Lower the presser foot handle;
  • Disconnect the remnants of the plastic housing;
  • Take the hook out of its holder.

No further disassembly is necessary. All parts can be reached with your hands or a syringe. Further order of lubrication is as follows:

  • Position the machine as if it were going to be used for sewing;
  • Fill a syringe with lubricant;
  • Slowly turn the flywheel counterclockwise;
  • Drop the oil on all the parts and their joints, which will begin to move and rotate;
  • Never touch plastic parts and gears that have already been lubricated with a special composition, it can damage them;
  • Lubricate the parts of the needle bar in the friction points;
  • Remove excess grease with a cloth or rag;
  • Check the operation of the assemblies by connecting the power supply;
  • Assemble the machine and give it a couple of hours so that the connections of parts soaked in oil;
  • Run for a couple of minutes with the foot up.

How to lubricate a Janome sewing machine

Janome are popular machines, so the question is relevant. As with any machine, they need constant prevention of damage and lubrication. At least the major components that drive the unit should be treated.

Before working, it is important to read the instructions for cleaning and operation, consider all the explanatory drawings. It is necessary to remove the lid of the device and pour the grease into the special holes, as well as apply it to the rubbing elements.

Lubrication of the Brother machine

No less popular brand of machines. It has its own instructions, but if you’ve lost them, it’s important to remember that a few drops of oil will be enough for treatment. It should be applied only to metal surfaces, avoiding the lubrication of the plastic.

Important! Brazier especially needs quality wiping of excess oil after machining, as well as idle running for consumption mechanisms.

Singer

Quality Singer machines need lubrication much less often, but still require maintenance. Cleaning them should start with the needle plate. To do this, the screws are unscrewed and the cleaning is performed. Next, clean the hook: take out the cap, and the locks are pulled apart. Take out the hook parts and dust them off. Do the same with the spinning unit itself.

Astralux

  • Remove the needle plate by turning the flywheel until the needle is in the up position;
  • Clean the bottom feeder. To do this, take out the bobbin cap and use a brush to clean the conveyor belt;
  • Clean and lubricate the mechanisms. Take out the bobbin and cap and swing the two holders apart. When this is done, the hook will come out freely and you can lubricate the machine;
  • Put the bobbin and hubcap back in place by turning the handwheel.

Vertical hook machines

They especially need to be lubricated, even the imported ones. The steps are the same: Remove the bobbin and open the catches, take out the hook parts and carefully wipe them clean. Put everything back. With these machines, it is important that the needle bar is in the up position.

Horizontal hook machines

Most of these machines have non-lubricated shuttles, but this is a trick to sell new equipment when the old one will break because of improper use. Any moving mechanism needs lubrication.

Machines with rotary rotary hook

This type of shuttle is the most reliable and lasts the longest. Another advantage of it is its high sewing speed. This is due to its popularity in industrial machines. For long life, it needs to be cleaned and dripped with three drops of oil at a time.

Brother sewing machine set-up and use guide

All women in the household face problems such as sewing and mending. Sometimes an item needs to be sewn or repaired in a hurry. For some people it is a hobby: people like to make things for themselves and their families at home. Not every time a manual stitch will be of high quality and presentable. In many cases it may be necessary to use a sewing machine. There are many different models on the market today, differing in price, functionality and workmanship. Brazier machines have also proven themselves. How to work with such a machine and how to change the legs for a sewing machine brother. told in this material.

How to oil a brother sewing machine. How to choose oil for sewing machines

Before starting to lubricate the sewing machine should be thoroughly cleaned by removing from the main nodes of its mechanism scraps. Dust and dirt particles, old oil residues. Remove the upper and side housing covers, unscrew the needle plate with a screwdriver or. Remove the hook from the hook mechanism, the bobbin from the hook, and clean it inside and out. The main focus on cleaning the shuttle mechanism, gearbox, its rotating and motion mechanism. Also clean all easily accessible bushings where moving parts are rubbing.

Clean the hook with a special hard brush or a brush that comes with the sewing machine, or whichever is more convenient for you. Use a clean, lint-free cloth to clean wide surfaces. Use tweezers to remove dirt from hard to reach places.

See also  How to remove the mower spool

Lubricate the machine with special machine oil. Use the jug or syringe to carefully apply a small drop of oil to all friction-prone parts and assemblies of the machine. Turn the handwheel toward you several times to distribute the oil evenly over the surfaces of the rubbing parts. Wipe off excess oil with a cloth. Afterwards, return all parts removed from the machine and fasten them well.

Grease the sewing machine depending on how often it is used. If you sew on it daily, lubricate it once a week. For less intensive but regular use, lubricate the machine once a day. If used infrequently, lubricate once every six months. Be sure to lubricate the machine after long periods of non-use.

Using other oils that are not designed to lubricate the sewing machine is forbidden, because it will cause damage to the machine. For example, vegetable oil dries out very quickly (in 2-3 days) and puts the machine out of operation. Good machine oil should have a light color. Do not use oil past its expiration date.

It is very convenient to use a disposable syringe to lubricate sewing machines. A long, thin needle can be used to lubricate any hard to reach parts of the machine. The oil is very economical when using a syringe.

After buying a new sewing machine, remember to read the included instruction manual. If you don’t, you could damage the working mechanism and your joy would be spoiled.

A new machine is usually coated with grease. Before you start working, kerosene must be removed. Two drops of kerosene drop in those places that should be lubricated according to the instructions. If kerosene is not available, washing with machine oil is acceptable. Wash all parts that are not covered with paint. After cleaning, run the machine idle (without threading) to remove the remaining grease. Then wipe the machine with a soft cotton cloth.

Machine oil should be in a special oil can. Nose of it is introduced as deeply as possible, drip a couple of drops. The shuttle gear also needs lubrication. Do not forget about the parts that are under. After applying the lubricant, turn the flywheel several times to improve lapping of the parts and to spread the lubricant evenly.

Before you start sewing, put 2 drops of oil into the hook and sew on the unnecessary fabric. Before each sewing session, wipe off the dust and check for grease. If you sew rarely, one lubricant for a month is enough.

Sometimes the machine needs extra cleaning. To clean the gear rack, put the needle up, remove the presser foot. Pull back the slide plate, unscrew and remove the needle plate. Then tilt the bobbin case ring and take out the hook. You can tilt the body of the machine back for ease of operation. Remove dirt with a special brush. If not, a toothbrush will do. Be sure to remove dust and grease from the sump.

How to Remove the cover of a Brother sewing machine. LS14 HC14 LS17 | Abi’s Den ✂️����

Next, lubricate the machine idle at low speed. Be sure to take care of lubrication of the flywheel by injecting two drops of oil into the lubrication hole of the sleeve. Also lubricate the motor unit, foot parts (on the foot machine) and cone studs.

Selection Recommendations

When selecting a Brother brand sewing machine, there are a number of important nuances to consider.

  • First of all, you need to clearly determine the purpose of further use of the sewing equipment. If you plan to buy a machine for minor home repairs, you can consider models with low power, which stand out for their good performance and affordability.
  • The treatment of dense fabrics requires a device with the ability to adjust the distance between the blade and the presser foot, as well as a high power (in the range of 60-80 W).
  • There are situations where the size of the sewing machine is also important. The most compact in the range of presented units will be machines with computer control.
  • Not unreasonable to pay attention to the material used to manufacture the body model. Today the brand produces products in metal and plastic versions, but the first type will be more resistant to mechanical damage.
  • Sewing speed. an important parameter for sewing equipment. As a rule, domestic models perform from 800 to 850 stitches per minute, while varieties of the professional range can do about 1300 stitches.
  • Models also vary in the location of shuttles. In models with a vertical type it is easier to perform troubleshooting relating to the tension of the threads. Rotary shuttles allow you to make a stitch in the process, the length of which will be 6-7 mm.
  • Studying the proposed range of sewing equipment, it is also recommended to pay attention to the equipment of the model you like. It is important that the device is implemented with several spare legs, perhaps a walking foot, bobbin cap, an additional device for embroidery or assemblies, etc. д.
  • For a sewing machine, it will be important the number and types of operations that the device can perform. For budget models, recommended as a home sewing machine, will be sufficient 10 operations. As for the electromechanical varieties, they can do about 40 kinds of stitches, computer stitches. 150.

Related Posts

| Denial of responsibility | Contacts |RSS