How to make a grinder out of corner grinder. Ribbon grinding machine

make, grinder, corner, grinding

What can be done from a corner grinder with your own hands: ideas for homemade

The question of what to do with dried and cut off branches in the garden, for summer residents, is usually solved simply. This “garbage” is simply burned. And at the same time, if you grind the branches, you can already use them in the garden for various purposes. Today’s story, which Vasily Alekseevich Kayumov sent us from Timashevsk, Krasnodar Territory, will tell you how to make a grinder for branches without expenses without costs and completely without costs.

My garden plot is small, since most of the territory is occupied by buildings, including a garage, which is a “part.time” workshop. But the problem of dried branches that necessarily cut down is still quite acute. The thought crept into the head that to burn them, at least, wastefully. After all, if, for example, turn the branches of the apple tree into wood chips, it is perfect for the smokehouse. With this thought, I went to the workshop, where a corner grinder caught my eye. Since this all started.

How to make a grinding machine

You can make a simple machine from the hard disk of your PC. To do this, you will need a hard drive itself, abrasive, PC power supply. It will be intended to work with small details. When disassembling the disk, you should stick an abrasive on a rotating plane. After that, the structure must be connected to the PSU (power supply), and then fix the entire structure on the working plane of the table, supplying the revolutionary control regulator, the switch.

DIY grinding machine

Grinding machines are represented by the following views:

In the manufacture of the machine, you will need:

The power unit must be taken from household appliances, for example, from a fan, a power supply. computer, battery. household. A wooden board on which screws should be fixed with an electric motor is suitable as a base for the above elements. The “Start” button must be attached to the base with self.tapping screws. The wire veins are fixed using an industrial stapler bracket. The work detail of the tool is a grinding circle, which can be purchased independently. The abrasive disk will be driven using an electric motor using two bushings. You can strengthen the design of the device if you take the engine from the washing machine as an engine. In addition to polishing discs, in this case, we can install sharp and abrasive on the tool.

Homemade tape grinder

As a working element in this type of devices is a grinding tape from an abrasive. Do.it.yourself machine will be stationary, and have large dimensions compared to the industrial model. For the manufacture of a sample, it is best to use a 2-3 kW power unit and a rotor speed of 1500 rpm. The radius of the leading drum directly affects the speed of moving the tape. The larger it is, the higher the speed of the tape is higher. The home.made design will not allow you to adjust the speed of the tape, however, you can influence the tension force by shifting the motionless axis of the tension shaft mounted on the engine shaft regarding the desktop. The workbench for a grinding machine should be made of wood or metal. A tape for a grinding machine can be made of abrasive paper sold in a construction store. The working element, which is the sandpaper, is set in motion using the transmission and drums with a power unit. Shafts are divided into leading and led. Drums can be made using sheets of a wood-steering plate, processing them on a lathe so that as a result of processing there are about 20 cm disks in diameter. When processing, one thing should be taken into account: the edges of the shafts are required to have a larger diameter compared to the central part, to automatically hold the tape. The dimensions of the rack will depend on the width of the tape and the distance between the shafts. At the location of the shafts in the canvas, it is necessary to make slots for smooth passage of the tape.

How to make a mini.grinding machine with your own hands

First you need to find foam to prepare the basis for the device. After that, you need to cut a hole for installing a circuit breaker in it. Then you will need an island and a power source, for example, a well.known Crohn battery. We hug a power battery (crown) to the foam base with island. We take a champagne plug and a handle rod. Cut the rod to the desired length, then put the handle rod on the cork with a blunt end and insert the edge of the rod into the hole for the shaft of the motor. After that, you need to cut the strip of abrasive tape under the dimensions of the cork dimensions. After you cut out the tape, it should be glued to the cork around the circle. This design is made of traffic jam and will be the working part of the machine. Carefully examine all the wires and connect them with twisting, isolate the connections with electrical. Try to start the resulting device. Now you have your own mini machine. Such a device is useful for performing simple small works, for which the usual grinding machine will be too large and uncomfortable. If you are an observant and patient, as well as a reinforcing person, it is completely easy to make a grinding machine with your own hands. To do this, you only need dexterous hands and a little patience.

How to make a grinding machine

You can make a simple machine from the hard disk of your PC. To do this, you will need a hard drive itself, abrasive, PC power supply. It will be intended to work with small details. When disassembling the disk, you should stick an abrasive on a rotating plane. After that, the structure must be connected to the PSU (power supply), and then fix the entire structure on the working plane of the table, supplying the revolutionary control regulator, the switch.

DIY grinding machine

Grinding machines are represented by the following views:

Graf. Bare Cylinder Grinder

In the manufacture of the machine, you will need:

The power unit must be taken from household appliances, for example, from a fan, a power supply. computer, battery. household. A wooden board on which screws should be fixed with an electric motor is suitable as a base for the above elements. The “Start” button must be attached to the base with self.tapping screws. The wire veins are fixed using an industrial stapler bracket. The work detail of the tool is a grinding circle, which can be purchased independently. The abrasive disk will be driven using an electric motor using two bushings. You can strengthen the design of the device if you take the engine from the washing machine as an engine. In addition to polishing discs, in this case, we can install sharp and abrasive on the tool.

Homemade tape grinder

As a working element in this type of devices is a grinding tape from an abrasive. Do.it.yourself machine will be stationary, and have large dimensions compared to the industrial model. For the manufacture of a sample, it is best to use a 2-3 kW power unit and a rotor speed of 1500 rpm. The radius of the leading drum directly affects the speed of moving the tape. The larger it is, the higher the speed of the tape is higher. The home.made design will not allow you to adjust the speed of the tape, however, you can influence the tension force by shifting the motionless axis of the tension shaft mounted on the engine shaft regarding the desktop. The workbench for a grinding machine should be made of wood or metal. A tape for a grinding machine can be made of abrasive paper sold in a construction store. The working element, which is the sandpaper, is set in motion using the transmission and drums with a power unit. Shafts are divided into leading and led. Drums can be made using sheets of a wood-steering plate, processing them on a lathe so that as a result of processing there are about 20 cm disks in diameter. When processing, one thing should be taken into account: the edges of the shafts are required to have a larger diameter compared to the central part, to automatically hold the tape. The dimensions of the rack will depend on the width of the tape and the distance between the shafts. At the location of the shafts in the canvas, it is necessary to make slots for smooth passage of the tape.

See also  Grinding head for the lathe with his own hands

How to make a mini.grinding machine with your own hands

First you need to find foam to prepare the basis for the device. After that, you need to cut a hole for installing a circuit breaker in it. Then you will need an island and a power source, for example, a well.known Crohn battery. We hug a power battery (crown) to the foam base with island. We take a champagne plug and a handle rod. Cut the rod to the desired length, then put the handle rod on the cork with a blunt end and insert the edge of the rod into the hole for the shaft of the motor. After that, you need to cut the strip of abrasive tape under the dimensions of the cork dimensions. After you cut out the tape, it should be glued to the cork around the circle. This design is made of traffic jam and will be the working part of the machine. Carefully examine all the wires and connect them with twisting, isolate the connections with electrical. Try to start the resulting device. Now you have your own mini machine. Such a device is useful for performing simple small works, for which the usual grinding machine will be too large and uncomfortable. If you are an observant and patient, as well as a reinforcing person, it is completely easy to make a grinding machine with your own hands. To do this, you only need dexterous hands and a little patience.

How to make a polishing machine with your own hands

How to do something yourself, on your own. The website of the home master

That every car owner is sure that polishing the car has a purely aesthetic disposition, allowing the car to glow brightly and gleam in the sun’s rays, as it is also called the light of street lamps and the headlights of other participants in the movement on the road. But the process in question has the next. not so trivial, but even more fundamental and responsible role associated with the protection of the coating and, as it should, all that is under it.

make, grinder, corner, grinding

Why is it necessary to polish your own “iron horse” than and how, in which case, this should be done? Before responding to all identified problems and proceed to the tips regarding the technical part of the process, it is necessary to clarify that polishing is abrasive and protective.

Protective polishing is a fairly common process. To do it is an option arbitrarily often, although it is also not recommended to get involved here: at least what a mechanical effect on the car coverage (adopted reduction. LKP), especially using chemical compositions, perfectly within certain boundaries. In fact, protective polishing allows you to give the car a gorgeous brilliant look and at the same time protect the paint from exposure to all sorts of negative causes. dust, ultraviolet rays, etc. D.

The essence of the abrasive (it is also called restorative) polishing is to remove a very small malekhan layer of car coverage for the removal of scratches, and in addition to mud deposits, various salts, reagents, etc. D., Besizbanly formed during use of at least any vehicle. Due to the fact that this operation reduces the thickness of the paint layer, it is not recommended to do it ardently without special need.

Abrasive restoration

It should be immediately mentioned that polishing, no matter how deep it is, is not at all a panacea against various troubles will not help to correct the complex flaws of the coating, for example, large chips or the deepest scratches.

But small tasks, such as microzarapins, microcracks, scuffs, clouding of the surface, fading, loss of brightness, etc. P., She will remove without effort. Although it looks different: it is still necessary to work hard, while significantly.

Read how to use a tile.cutting manual video Russian

The technological process of polishing the car body is quite complicated, alas, having mastered it. The motorist will be able not so much to seriously save on caring for his four.wheeled pet, however, to give a wonderful appearance to things outside the limits of the auto sphere, for example, furniture and other elements of the interior. But you should start with the basics, more precisely, with the consideration of the structure of the coating of the car, which consists of:

  • primers. a composition applied by the first layer on the surface of the metal prepared for the coloring, smoothes its absorbing characteristics and provides reliable grip of the entire coating with body details:
  • paints. substances used to give objects (in this case.the body) of one or the other color and the opener;
  • varnish. a solution based on polymer resins that form a strong film playing the role of a protective coating. Restoring, it is also abrasive polishing from flaws that occur specifically in the upper. varnish layer of car coating. Now, having summed up the theoretical base of the process, of course to run to the practical part.

Preliminary step of independent polishing

For polishing the body, a number of chemical tools and compositions are useful, also some devices, a special tool and consumables for it. Depending on the degree of exposure to coating the car, the polishing compositions are abrasive, medium.ababral and non.pectoral

Apart them should be armed with a solvent, a degreaser and, perhaps, a special tool for removing bitumen. In this case, chemistry ends and physics begins, t. e. tool, devices and some supplies, and more specifically:

  • polishing machine;
  • polishing circles (plus, maybe mandrel for their fastening);
  • napkins or microfiber towels;
  • cardboard (painting) tape.

Speed ​​controller for grinding a machine (corner grinder) or how to make a polishing machine from a corner grinder

Homemade Sander. To make the sander with your hand. Nothing Complicated. The Video Shows How to Make a Homemade Centrifugal.

Homemade Sander.

Polishing the car with corner grinders. Our client remains for and against painting a car. Auto polishing. A car primer. putty.

Before starting work, you need to wash with all the likely thoroughness (it is better to dry the highest pressure using special shampoos) and dry it.

In this case, the preparation is finished: time to run in actually to polishing.

Coarse effect before polishing

First of all, a special tool must be removed by a particularly persistent dirt, which always remains even after the most painstaking sink. spray bitumen, traces of insects, etc. D. Both special aerosol cleaners and ordinary neutral solvent are used here.

Read how to make a polish machine from a corner grinder

Further, the polished surface must be degreased using a napkin as it is also called microfiber towels and at least a suitable detector. If stable pollution remained on the body, then they should be removed by processing with special clay. A fundamental remark: only those surfaces that are polluted are subjected to clay processing!

Here, as well as in various other matters, the main thing is not to overdo it, do not overdo it, t. to. This very operation is 90% determined by the van of the entire venture with polishing.

There is an option to use an eccentric grinding machine with an adjustable spindle rotation frequency

(very highest turnover is guaranteed to damage the body of the body), but in the absence of an overwhelming experience it is better not to risk and use the manual grinding method.

He will be subject to consideration in details, t. to. Obvious logic gives a hint that most of the readers of this article are not specialists in the field of polishing. What you need, we take a sheet of emery moisture resistant paper with grainity P2000 and soak in a basin with water at room temperature to give elasticity. A very fundamental moment is the correct position of the skin in the hand: the corner is clamped between the little finger and the ring finger, and the thumb holds and directs the segment of the paper. We abundantly moisten the chosen area from a sprayer or (preferably) hose with running water.

See also  Brush replacement in angle grinder. Care and Storage

The nuances of the process

This stage begins with a small area of ​​abrasive pasta. You can try to smear the circle itself for polishing (the one that is lighter). A minimum mode is set on a typewriter using a disk regulator located at the handle.

To determine whether the surface of the metal is polished, it is necessary to compare it with other details. After processing, it should shine stronger than after varnishing (evenly and without a matte bald).

According to the same technology, the following two pastes are used: first, the average amiberic, then non.abrasive.

Here are some tips on how to properly polish the car:

  • The body can be wetted a little with water so that the paste does not dry out.
  • Clean the circle of adhering pasta to achieve maximum polishing efficiency.
  • If the processed surface overheats, then it is time to move to a new area, and then, if necessary, return to the cooled.
  • If you do not set small speeds, the pasta is marked to the sides. After working at low speeds, you can add a little, but not exceed 2500 per minute.
  • Before using a non.grazing paste, the surface is washed out, and the circle changes to another.
  • During the work of the grinder, you need to monitor the cord so that it does not touch the surface of the body, otherwise the scratches cannot be avoided. Experts recommend throwing the power cable over the shoulder or resort to the help of a partner.
  • If you keep the machine not perpendicular to the surface, but at an angle, stains are formed.
  • It is unacceptable to touch the circle of plastic elements. They can be irreversibly spoiled due to the effects of abrasive paste and a hot rotating circle.
  • It is enough to walk slightly along the ends, but do not cling to the edges of the corners so as not to damage the circle.

Now you know how the car is polished after painting with your own hands. So that the work is completed completely, the car is thoroughly washed out. The presence of a toothbrush is useful here. This outstanding tool will help to extract lumps of pasta of cracks and corners. Within a few hours of hard work, the result will be obtained.

Myford MG-12 Plain Cylindrical Grinder

After the car is washed, you can proceed to the manual guts with the finish paste. It is applied to the surface by means of dry fabric without pile.

Before polishing the car after painting, many motorists have doubts about the need for this time.consuming and several costly process. However, it is worth listening to the opinion of experts who recommend polishing.

The procedure for using the polish can be repeated. After all, it depends on the brand, withstands from 4-8 to 8-12 visits to the sink. With repeated application of the composition, grinding is not required.

Information is useful to novice Malyars and motorists.

Even an inexpensive car will be able to make a pleasant impression if it is well polished using modern means. But how to correctly? This operation is important not only from an aesthetic point of view, since the surface is protected at the same time and the service life is extended. Constant movements, negative weather conditions, temperature differences, road dust negatively affect the paint of a car, with time scratches and chips appear. Therefore, the correctly selected polish will provide a reliable protective coating and change the appearance for the better. It is important that all work can be done independently.

We make a grinder of corner grind

Many can say that the “corner grinder” is the same angular grinding machine, but some subtleties are hidden here. It should be borne in mind that the corner grinder has very high speeds and often a pretty decent weight. To polish the surface of the corner grinder, you need to have considerable experience in this matter and use special polishing discs and circles. The grinding machine has much lower engine speed and weight. For the operation of the factory grinding machine, a certain experience and dexterity are not required. It is possible to make a good grinding machine from the corner grinder, which is not inferior in its parameters by the factory typewriter, only by finalizing its electrical circuit, by installing the regulator for lower revolutions and by using special grinding nozzles.

Do not forget that grinding is always associated with a lot of dust. Preparing for grinding, do not forget about yourself! Protective mask and respirator are the best helpers for grinding. You can find such an option where the mask is combined with a good respirator.

The respirator filter will be clogged very quickly, so you need to prepare several pieces for operational replacement at once. Only after careful preparatory work can you start grinding.

Grind the tree

Wood is a unique material. It is manually polished well, but with a corner grinder you can achieve very good results. Some snobs argue that the corner grinder cannot be grinded at all, but this is from ignorance and inability.

The main secret is the grinder is used at minimum speeds. If the corner grinder has a speed switch, then there will be no problems. At large speeds, sandpaper will be very quickly and very tightly clogged with wood. In this mode, it will not be enough for five minutes of work. Optimal speed of not more than 6,000 speeds.

Another secret is not to grind the whole area of ​​the circle. If you grind the entire surface, then circular traces will remain on the wood. So that there are no traces of sandpaper at all or they would be minimal, it is necessary to grind only the upper sector of the circle. Machine movements should be along the wood fibers.

This method can get excellent results when grinding the lining. The board becomes smooth and does not save the traces of the tool. No need to get carried away and change the sandpaper on the circle in time.

Similarly grinds the log house. Here it is desirable that the support plate is thin along the edge. With such a plate it will be easier to polish the narrow places of the adjustment of the logs. Otherwise, this work will have to be brought a chisel.

We work on concrete

If it was not possible to purchase a branded protective casing with a pipe for a vacuum cleaner, then it can be done with your own hands. To do this, take the used bucket of putty or glue with a diameter of a little more than a circle of corner grind. Cut the bottom part at the height of a slightly larger collected grinding part.

Cut the hole in the bottom for installation on the gearbox and a hole for plastic plumbing angular discharge. Now we connect the vacuum cleaner hose to the pipe and work calmly.

The grinding circle must be designed for stone processing. Concrete and concrete surfaces are preferable to grind the entire surface of the circle. This will save processing time, and align the surface plane well.

Grinding the concrete floor must constantly control the plane with the help of the construction line, because due to the different density of concrete, you can make recesses. To process the docking seams between concrete filling, it will be sufficient to achieve one combination by level.

It is good to polish the concrete floors and surfaces of the Matrix diamond grinding cup. If the corner grinder is 150 mm, then a cup of 125 mm.

Grinding metal surfaces

Metal is polished according to different requirements. Most often, the metal is polished for painting or for further polishing. The main tool is recognized as a supporting cup with interchangeable sandpaper. The selection of sandpaper depends on the degree of processing and on the state of the metal.

During grinding, it is necessary to work only part of the disk. There should not be unprocessed areas on the surface.

Processed surfaces of ordinary steel, it is advisable to cover with a primer. The moisture contained in the air can very quickly cover the metal, and cause the appearance of rust.

We make a grinder from a drill

To turn a regular, household electric drill into a grinding machine, you need to equip it with a special nozzle. a working drum or a special supporting plate, depending on the task. The support or grinding plate is a plastic or rubber base with glued sandpaper and a shank for a clamp in a drill cartridge. Plates with a flexible shaft are suitable for working with an untouched drill, and with hard it is better to use only for a well.fixed drill.

Grinding drums for a household drill constructively are a regular cylinder, shank and sandpaper glued to the cylinder. When using drums, the working surface of the grinder is located parallel to the axis of rotation.

See also  Makita angle grinder with variable speed

DIY simple grinding machine

I somehow needed a grinding machine, but I did not have it and it was decided to make a simple machine with my own hands. I myself did not expect that there would be such an amazing effect from the work of this homemade.

For this craft, we will need a fan that can be taken from any computer, but immediately I want to say the larger fan, the more powerful the machine will turn out.

We will also need a little plywood, a handle from some furniture, I took it from a drawer of a drawer and a circle from a corner grinder or a grinding machine,

  • You can buy it in a store, to which a skin or sandpaper is simply planted, I have it with a diameter of 125mm.
  • So, we start to do, my fan turned out to be 14 by 14 cm, if anyone does not have it, then you can order on Ali, here is a link.
  • We cut out the same square blanks from plywood to the dimensions of this fan, we will need 2 pieces to subsequently connect them together with bolts.

I cut them carefully with a jigsaw. The edges of the plywood were sandwicked to give a normal look and remove the burrs.

Then I took the crown for 30 mm and drilled the hole in the center. The hole must be drunk in only one of the plywood.

But to the second plywood blank, I screwed the handle, as shown in the photo.

Then we take our fan and approximately in the center of one of the blades we drill the holes under the bolt M10 and screw it.

We need it so that an imbalance appears on the fan impeller, this imbalance and help us grind objects.

Instead of a switch, I just glued a fast connection plug with a 12 volt power supply unit.

Now we collect, that is, we twist our fan with plywood blanks with four bolts. If the bolts are long, then we cut off the excess corner grinder.

In the middle of the holes made in the faner, I poured a thermocles and glued a grinding circle. With experience, I can say that the circle does not fall off.

Now we only have to plant sandpaper on a circle and serve food.

The machine will pleasantly surprise you with your work and you will not regret that you spent a certain time for its manufacture.

Rules for the use of corner grinder in the processing of various materials

Thanks to the universality of use, the angular grinder was very widespread both at the construction site and in everyday life. She firmly entered the sphere of activity of professionals and just artisans. With its help, you can process almost all known materials, as well as successfully carry out installation and locksmiths. Consider the main spheres of use angular grinder.

Work with wood

When working with wood, an angular grinder equipped with a petal or a plaque of an emery disk will become an excellent assistant for grinding and polishing even planes. Changing the size of the granularity of the emery, you can perform a wide range of operations to align the wooden surface. It is very convenient to remove the old paint with an angular grinder. When grinding a tree, a corner grinder, it is vital to use a respirator that protects the breathing organs from dust.

The main rule of security. It is strictly forbidden to cut, drill or milling wood using corner grinders. High revolutions of the working tool, multiplied by the tendency of wood to cracking, create very dangerous factors. Numerous tragic cases of visual confirmation.

Log grinding is performed by corner grinder quickly and efficiently

Work with ceramic tiles

Often corner grinding is used when working with ceramic tiles. Of course, the main tool for professional tile is manual tile cutter. But the corner grinder is also necessary, with its help small cuts on the tile are made, the edge is aligned, unwanted sharp corners are smoothed out.

Using modern nozzles with diamond spraying, you can cut ceramic products with high accuracy, while avoiding chips or cracks.

Sometimes professionals prefer cutting a corner grinder, since manual tile cutter gives chips along the cut line. This is especially relevant when the front surface of the tile is not glossy, but a tuberous (for example, in a bathroom where it is customary to lay a tile that has an anti.slip property to the floor).

Helps out a corner grinder and if you need to make a small amount of work. For example, put a tile apron above the table in the kitchen. Such a task can be possible for any person. Corner grinder with a diamond disk will help save on buying expensive tiles.

Tile fitting with a corner grinder is done in one movement

Sharpening of the chain saw

Sharpening of the chain of the chainsaw. an operation requiring certain skills. A person without experience can rather spoil the chain than to sharpen it correctly. Evasion from the angle of sharpening leads to the fact that the chain turns the chainship of the chainsaw during operation, produces arcuate cuts and jams in the thickness of the wood.

When sharpening a chain saw, the angular grinder must be fixed

Starting to sharpen the chain using a corner grinder, it must be clearly understood that the main thing is to withstand the same angle of sharpening at all links. To do this, either the angular grinder itself, or the chain is stiffly fixed using special clamps or clamps. The thickness of the sharpening disk should be equal to the inner diameter of the circumference of the tooth of the chainsaw (3-5 mm).

If the corner grinder has a drive speed regulator, then it should be set to a minimum position corresponding to 2.5-3 thousand. rpm. Metal overheating (turning) during sharpening cannot be allowed. this will lead to a vacation and a decrease in strength.

Cutting and cutting metal

The angular grinder in the field of cutting and cutting metal products is widely used. Using discs made specifically for working with metal, with the help of even low.power corner grinding, you can cut steel, aluminum or cast.iron products, as well as leaf iron.

Cutting steel structures with corner grinders is performed by a metal disk

Of all types of metal disks, two most commonly applied in practice can be distinguished:

The first is designed for cutting all types of metal. The second. for processing a metal surface (grinding and polishing). The cut.out circle can also be cut by leaf metal according to certain patterns, cut the specified figures, circles, and so on. The peeling disk perfectly removes rust, cleanses of the old paint, levels any metal surface.

Cutting metal pipes

An indispensable tool was an angular grinder in works related to the installation of heating, drainage and water supply. Wherever there is a need to cut pipes, the use of corner grinding, together with metal disks, gives a practical result, a significant saving of time and increases the efficiency of labor. To cut off the pipe exactly, the cut must be made strictly at right angles.

When cutting the pipe with a corner grinder, it is necessary to protect your hands with gloves

How to cut a gas cylinder

Sometimes in the farm there is a need to cut the old gas cylinder. Since gas cylinders have thick.walled (3 mm) design, they can be used for various household needs.

The cylinder can become a tank for storing water, and a water.bearing tank for a summer shower, and barbecue, and a hearth for a home forge.

make, grinder, corner, grinding

For disassembling the score, you will need:

  • Release the balance of gas from the cylinder, completely unscrewing the adjusting valve.
  • Cut the brass valve with a hacksaw. In the process of sawing, the cut place should be abundantly watered with water to prevent the possibility of sparking in the cut.
  • After the crane is cut and a wide hole opened in the upper part of the cylinder, several water buckets should be poured inside the funnel, and it is best to fill it with the entire volume of the cylinder. This procedure will clear the bottom and walls of the cylinder from gas condensate, which is a thick liquid similar to liquid soap. When the spark enters the condensate, a fire occurs. You can cut the walls of the cylinder with a corner grinder only after the procedure for its “wash” with water.
  • Cut the walls of the cylinder.

Related Posts

| Denial of responsibility | Contacts |RSS