How to install a spool on a grass trimmer

How to Change the Spool on a Benzocosa

Since the choice of trimmer for grass, we looked in the previous article, now we will tell you how to correctly fill the trimmer for grass fishing line, and what is better to select based on the criteria of work.

After you have purchased a grass trimmer and started to use it intensively, at some point there will be a question of replacing the line, as this is the most wearing element in the tool, the intense use of trimmer for grass will lead to frequent substitution of consumables.

What kind of lines are there

A common type of fishing line that fits virtually all types of spools is a cord with a circular cross-section. How to change a spool of fishing line on a blade, on a chain saw how to change the blade on a. This ordinary fishing line, applicable for mowing succulent grass, but mow dried grass with it will be much harder, and the more it does not cope with shrubs.

Usually, cross section, with which you can mow young grass, does not exceed 1.6 mm. The thicker the cord, the more coarse grass it can cut.

There is a fishing line with a sharp edge in the form of a star or a square, such a version is more adapted to mow dry grass just by having a sharp edge, but the disadvantage is its greater wear and tear, and on the strength it concedes round cord.

There are lines with improved aerodynamics with appropriate dents, scales and notches, a similar product makes less noise, but use it only on benzokosa, since the output of such thread from the spool is difficult, using it in most cases with discs, which are inserted segments. How to rewind the cutting cord on a spool how to change the blade on the bobbin on a brushcutter. The disadvantage of such a product is its fragility.

In most cases, gasoline trimmers with an engine more than 1.5 liters of power.с. they use cords with an iron cord inside. This thread is perfect for mowing dry grass and small bushes. The presence of a core, positively affects the durability of this material. The disadvantage of such cord is its price, which is significantly higher than the above listed opponents.

How to remove and put the coil on the mower!

Subscribe to the channel!And we teach you everything)))

Black & Decker Grass Trimmer Spool Line: How to Install

STIHL FS 55. Changing the brushcutter spool to a knife

How to install the 2-blade blade on STIHL STIHL FS 55 brushcutter. How to change the line in the trimmer and what kind of line on the reel to load the line on the trimmer for grass. Video annotation, how to change the mowing heads benz.

How to tuck the line into the grass trimmer reel

It will take about 10-15 min to wind up the fishing line. What is a grass trimmer reel? Plastic housing with cassette inside that has a hook for winding the line comfortably. Virtually all trimmer reels have a similar attachment principle, a central button screw that, when pressed, makes it possible to pull out the line of the desired length. How to remove the spool to change the line and disassemble the spool on the trimmer and. The photo below shows several examples of different trimmer reels.

Bobbins trimmers, the motor which is located near the ground, have a different attachment to the axis of rotation, they have two buttons on the spool, located at the edges, which must be squeezed, otherwise the substitution of thread in the same does not differ from other cassettes.

The principle of the correct winding of the line is identical in all of the above cases, so let’s look at the standard version with 2 tendrils as an example.

To remove the spool with the line you need to unscrew the screw, located in the center, but note the thread is left, so you have to turn it clockwise, it is made specially so that during operation it is not opened under the influence of centrifugal force.

install, spool, grass, trimmer

Next, using a screwdriver, dismantle the head and remove the spool, which actually winds the line. Measuring the desired length and folded in half, it is necessary to tuck the line into the spool, eventually bringing its ends opposite each other (for this purpose there are special slots for fixing).

After that, you need to assemble the head in reverse order, passing the ends of the cord in the two respective holes.

How to Replace the Spool on a Weed Eater SG11 String Trimmer (Part # 952701663)

See also  How to assemble a lawn mower starter spring

If there are any doubts or is not quite clear how to charge the line on the trimmer for grass, we advise to see how to correctly wind the line on the lawnmower. How to change or wind the line on the grass trimmer reel. In this video clip carefully step by step instructor will open trimmer head, measure the required amount of line, usually this is from 2-to-4 meters, and demonstrates the assembly and installation of the trimmer for the grass.

How to change the reel on a STIHL grass trimmer

Trimmer for grass, whether he gasoline or electronic, is the only true solution to mow grass in inaccessible areas with whom can not cope wheeled mower. In the role of cutting tools in trimmers used iron knives or a special fishing line, which is tucked into the grass trimmer spool for. Unfortunately, however, trimmer heads do not always work properly over time. Some malfunctions of course can be corrected at home, and some require complete change of mowing head.

Mowing heads for trimmers can be of different designs. both ordinary and complex. The illustration below shows a disassembled automatic trimmer head from a Husqvarna brushcutter (Husqvarna).

This type of head is included in the majority of gasoline mowers and electric trimmers, such as STIHL (STIHL), Patriot (Patriot), Champion (Favorit), Bosch (Bosch), Huter (Huter) and others. The design of the mowing head is pretty basic. It includes the following parts:

  • The base of the mowing head;
  • Button for the automatic filament feed;
  • bobbin (spool), where the line is threaded
  • spring
  • eyelets. through them the line goes out;
  • trimmer head cover;
  • line (cord).

there are also more ordinary trimmer heads, shown in the following photo.

These nozzles do not allow you to change the length of the line in automatic mode (after pressing a button). If the filament breaks, the mower has to be stopped and the cord is changed manually.

Users of electric trimmers and lawnmowers often have trouble with the automatic mowing head. Coil failures can be as follows:

STIHL brushcutters, threading the AutoCut 25 2 mowing head

If the line is not lengthened by lightly striking the grass trimmer reel on the ground, the following are the prerequisites.

Option 1. there is a jam, t.е. Clamping the filament between the coils. This fault is usually caused if the customer has wound the line unevenly, crosswise or with insufficient tension. If the mowing head rotates at high revolutions, the filament is tightened by the centrifugal force, and the filament is caught between the spirals. To remove the difficulty will have to dismantle the coil on the trimmer and rewind the cord correctly, in other words, smooth turns with a good tension.

Option 3.2. The line is too short and protrudes from the head. The line may not come out when hitting the ground if the ends protruding from the head are not long enough (short). Then the centrifugal force is not sufficient to stretch the line. Because it requires a pause machine (turn off the engine on another disconnect trimmer elektrichesky for grass from the network) and pull the line manually, having previously pressed the button.

Option 3. The line is soldered inside the mowing head. This causes the spool to stop spinning when the button is pressed. In the main, this occurs for several reasons: poor quality cord, overheating the coil during prolonged use of the unit, the impact of fishing line on solid objects.

  • In the beginning, the cord from other manufacturers is made of low-quality and fusible materials that do not withstand mechanical and thermal stress. Therefore, preference should be given to “branded” lines.
  • If you do not look at it got the line of unknown properties, and it often soldered in its time of operation, you can follow the example of some users, who after filling the cord in the coil lubricate it or silicone grease (from the canister), or mineral oil. This procedure is much less likely to solder to each other turns of fishing line.
  • Also, the line may meld if it hits a hard object while mowing (a rock, fence, dry twig, etc.) or if the line hits a hard object.д.). Once this is done, it stretches a little and pulls back into the head at a high rate of speed. The friction warms the cord, and its coils stick together. The only thing to do to correct this malfunction is to open the grass trimmer’s reel and rewind the line.

STIHL fs 38 trimmer bearing replacement

There are situations where the user of grass trimmer notices a very sharp flow of line. Not once did he hit the button on the ground to lengthen the line. A prerequisite that the line extends spontaneously, being cut by a special knife on the housing of the machine, is the lack of a spring in the mowing head. It is not uncommon that first-time mower users, trying to load line into the spool, either forget to install the spring in the mowing head or completely lose it when opening the cover and in the near future do not even suspect its existence.

Also the line can be lengthened without using the button, if the spring is loose. If check of the spring has confirmed this fact, you should put some washers under it to strengthen its clamping characteristics.

Owners of trimmers, mostly new, get confused, adjoining to panic when it becomes necessary to change the cutting tool or line in the reel. Often, when trying to unscrew the mowing head, users simply wreck it without realizing that it is unscrewed in the opposite direction. To avoid this, if it will be necessary to change the tool, it is recommended to study in detail the step-by-step annotation given below.

  • While tucking the line in the coil, turn off the engine brushcutsa or no power trimmer elektricheskom for grass, to avoid injuries that occur when accidentally starting the rotation of the cutting tool.
  • Unscrew the bit attached to the gearbox shaft. To do this, the shaft must be secured by aligning the holes on the washer on the axle, and inserting an iron bar or screwdriver there.
See also  How to change the wire in a trimmer

Gasoline tool ignition system

  • Take a piece of plywood on another textolite and draw a circle in a cross section of about 14 cm.
  • Cut out the disk with a jigsaw or other metal saw.
  • Drill a hole in the center of the disc to match the cross section of the gearbox shaft. Before putting the disk on the shaft you should put a washer on this address.
  • On the sides of the drive can be screwed small corners as it is also called to make 1-2 holes on the reverse sides. They will serve to refill their lines.
  • What to fix the line, to screw a few self-tapping screws into the plywood of course.

Such a homemade mowing head is fixed on the shaft with a nut. Screw or unscrew the nut without fixing the shaft is impossible. To change the cord it is necessary to release the self-tapping screws, to insert a piece of line of the necessary length and to press it again.

Also mowing head for fixing the line on its surface, of course, make of iron sheet. How to do this, you can understand from the following video.

install, spool, grass, trimmer

Grass trimmer reel and line threading with your own hands

In today’s agricultural economy scattered set of all kinds of tools that are designed to make life easier for gardeners and hobby gardeners. In my opinion, the lawnmower type of line trimmer for grass is one of the very simple, and ingenious inventions that can, in a matter of minutes, turn your overgrown with weeds homestead plot in well-groomed lawn. But no matter how clever the invention is, it needs care and repair. I’m not a supporter of rework of industrial tools, but in order to save money, I came up with and describe a useful addition to the line trimmer.

How an automatic reel for an electric trimmer differs from a manual reel?

Reel for electric trimmer can be presented in different variants, depending on the principle of changing the cord. One of the most convenient and easy to use is the automatic trimmer head.

This type of mowing head assumes an automatic change of the cord, without the need to perform any action. This type of reel is practical and convenient, it does not need to be adapted in a special way, so it is preferred to other types.

Still there are semi-automatic and manual heads for electric trimmers, which require an action to change the cord trimmer for grass. Automatic head from the listed types of coil differs in a higher cost, which is justified by the convenience of working with the tool.

Catalog of Spart store offers different types of heads at a pleasant price for Chinese trimmers and other brands of tools. Also in the store you can buy a crankshaft for gasoline grass trimmer of excellent quality.

Knife or fishing line. what to choose?

The lawn is able to decorate any country house. However, in order for it to look royal, it should ensure competent care: feeding the soil with fertilizers, regular watering and constant “mowing”. If you do not mow the lawn, a beautiful and flourishing green “carpet” will turn into a thicket of untended shrubbery. Thanks to such a modern invention as the garden trimmer for grass, working the site has long ceased to be dull and mundane. This tool has excellent mobility and maneuverability, and the motor installed in the device, will help to do all the work in the shortest possible time.

Petrol, cordless or electric: which one to choose?

  • Great freedom of movement. During operation, the electric cable does not interfere with the cutting of the grass, and there are no restrictions regarding the length of the cord. Gasoline grass trimmer allows you to cut the grass even on the most remote from home.
  • high power. Mowers are capable of removing vine stems and brush stems and can easily handle the toughest of grasses.
  • Large volume of work. Thanks to gasoline mowers, farmers can mow grass for their pets in no time at all.
  • Noisy operation
  • Non-environmental device. during operation, the gasoline grass trimmer emits a large percentage of exhaust gases, contributing to environmental pollution;
  • uneconomical, which is expressed in the constant refilling of the lawnmower with gasoline and oil mixture;
  • heavy weight.

Electric grass trimmer is a lightweight and mobile device, which does not affect the environment and does not require a significant expenditure of financial resources for refueling. Nevertheless, for all its advantages, it also has its disadvantages, namely:

  • low power, which does not allow you to remove thick branches and bushes. This parameter varies from 200 to 1500 watts. trimmer for grass, which has the lowest power range, is only good for cutting lawn grass, but for weeds, you have to pick up the tool with more power. The device with a power of 1000 watts is considered universal, it will allow you to remove both tender grass and tough stems of weeds;
  • power connection. In the case where you need to cut the grass, which is at a great distance from the house, and the length of the cable will not be enough, you will have to use extension cords, which is not very convenient.
See also  Which way to wind the lines on the multi-function grass trimmer?

Battery built into the device ensures the trimmer operation. Battery charge is enough for 20-30 minutes of uninterrupted work.

  • ease and convenience in operation;
  • High level of maneuverability, which allows you to remove the grass even in hard-to-reach places;
  • Requires no fuel and is not tethered to the electric grid;
  • Low noise level.
  • has low power, which does not allow you to remove hard and tall grass;
  • has a low performance, because after half an hour, it requires recharging.

How to Replace the Spool Assembly on a Weed Eater RTE113C String Trimmer (Part # 952701663)

When choosing a trimmer for grass, much attention should be paid to the cutting system, it can be of two kinds:

The line is wound on a bobbin inside the reel. When the motor is running, the bobbin rotates and the tips of the line, which are exposed to the outside, cut the grass. Despite its apparent fragility, the line easily cuts unwanted grass, thick weeds, and can even deal with shrubs. However, during operation, the line may wear out. Automatic feeding allows for do-it-yourself changes. If, on the other hand, the trimmer has a semi-automatic, you will need to hit the spool on the ground, and the system will release the ends of the line outside.

A number of rules should be followed when working with a fishing line:

  • The line or reel must not come into contact with hard materials. If you touch a curb, fence or stone, the line will shorten prematurely and the spool may be damaged.
  • Removing weeds with the tips of the line will be much more effective than using the entire length of the line. over, this action can damage the reel.
  • Grass that is too tall and exceeds 20 centimetres in length requires several cuts. Grass should be mowed from top to bottom, this manipulation is required so that the grass does not wind up on the spool.

Metal blade is installed in trimmers in cases where the engine can not cope with high loads. That’s why you will often find a blade in a petrol lawnmower rather than in an electric trimmer. The blade can be two-, three- or four-blade, it can easily cut both tough weeds and branches, and if the grass trimmer is equipped with a special disk with teeth, the device can even cut strong young trees.

In an electric trimmer, the motor can be located either at the top of the base, or at the bottom.

The motor located in the upper part of the grass trimmer, is considered the most convenient and comfortable, it can mow wet grass. This type of device implies only work with a line as well as a blade.

The bottom-mounted motor also has advantages. This grass trimmer can be used even by older people, it is more handy and convenient to work. Nevertheless, it is forbidden to mow in the wet, as there is a risk of electric shock from the electric appliance.

Comfort and convenience. the key to fast and high-quality work

The operation of the tool should not be heavy, so before you buy a grass trimmer, you should decide on the shape of the handle. The handle can be D or T-shaped.

The device with a D-shaped handle will allow you to cut grass in small areas that require an excessively high degree of maneuverability and swivel.

The T-shape will make it much easier to work because it has a similarity to a bicycle handlebar, which allows the operator to hold it with both hands and be less fatigued.

Devices with high power are heavy, which can weigh up to 5 kilograms. Less powerful grass trimmers will not be able to trim tough stems, but the light weight, will allow the operation of the device even the weak female sex.

To summarize, there is no one-size-fits-all device that can fit all conditions. When choosing a grass trimmer, you should take into account all the nuances: the size of the plot, the grass that grows on it, the presence of rocks and trees.

If the suburban area is characterized by excessively stony soil, you need to opt for a device with a fishing line, as a metal knife can be damaged. And an uneven and twisted blade can provoke a misalignment or gearbox breakage.

If the site is not often cared for, it is a lot of weeds, weeds, and shoots of young trees, trimmer for grass with a metal blade, will allow you to get rid of them in a jiffy.

We would like to advise you to pay your attention to high-class garden equipment in the online store EUROtools. Here you can choose a suitable trimmer for the grass, which will serve you for many years.

Related Posts

| Denial of responsibility | Contacts |RSS