How to dilute gasoline into a motorcycle. What gasoline can be poured into a trimmer for grass?

The ratio of gasoline and oil for a trimmer for grass table. The first launch of the lawn mower

Hello! I purchased a trimmer for PRORAB 8406 grass 1. How to make gasoline with oil correctly and in what proportion? I did not find the original oil from Prorab, I bought Hungsvarna HP oil. In the instructions for the trimmer it is written from third-party oils, you can use the oil mif \ 4 class oils, API TC-TB. In the case of using another brand of oil, the proportion of the fuel mixture does not change. Standard proportion of the mixture 1:25. But in a specialized store “Specialist” that Hungsvarna HP was sold to me, I urgently advised to dilute at 1:50 (as it is written in oil). Actually the question: if the instructions are written to dilute the oil by 1:25, and 1:50 is recommended in oil, then in what proportion to breed? And 1:25 is how much? 40 ml? I will not turn off the engine if I scout at 1:50? 2. How to properly run the engine? In the instructions, in addition to starting and disconnecting, nothing is written. Maybe you don’t need running.in? I read that there are such trimmers for the grass that you can work immediately after the purchase.

Do I need to lubricate the gearbox before work or there is already a factory lubricant? I hope for your help, thanks!

dilute, gasoline, motorcycle, poured, trimmer

1) Gasoline is always divorced with oil in the proportion as indicated on the bank with this oil! With two.stroke products (benzotrimers, chainsaws, etc.) You can use any oil for two.stroke engines, except for boat two.stroke engines. It is advisable to use oil from normal stores, where the probability of buying fake oil is minimal. It is better to take Husqvarna or Stihl oil. STIHL oil should be with a sealed neck. Beware of fakes. There is a risk of spoiling the piston immediately. 2) driving two.stroke products is not done! Please remember this! All two.stroke products are high.speed and love exclusively work on full gas! No half.gases are permissible! This leads to incomplete exhaust and shifts with oil sediments of the wall of the piston. As a result. bullying piston. So the full gas and every 25-30 seconds are discharged gas for 1-2 seconds to let the product rest and return to the normal temperature regime. 3) a gearbox in motorcycles with a straight shaft must be scored by a new grease every 20 hours. Oil from there comes out naturally during operation. This is done so that dirt, dust, etc. D. So if you do not want to get to replace the gearbox, score special gear lubrication every 20 hours. It is not difficult and the whole operation takes no more than 3 minutes. Lubric tubes are sold in each store with garden equipment and cost from 100 to 300. 1 tube is enough for 3 years. —- The concept of running the tool comes down to working with incomplete load during the production of the first two or three fuel tanks. For example, during a mowing not thick, low grass or sawing dry, not large wood. In no case should you run into the instrument at idle by burning a few fuel tanks. As a result of such running.in on the windows of the cylinder, a carbon carbon fumes form on the piston and in the muffler, which negatively affects the engine resource.

Ryobi 2 stroke petrol hedge trimmer running

Trimmer for grass, or lawn mower. a tool that cannot be dispensed with in the household. over, its reliability, efficiency and long life depend on many factors.

For example, fuel quality. This means that you need to correctly select oil for a trimmer for grass, observe the proportions when adding to gasoline and the rules for refueling the device.

Why do they buy trimmers for grass?

Comparing with similar mechanisms, they give preference to motorcycles when choosing the following functional indicators:

  • The mobility and small weight of the unit, allowing it to transfer it to distances, use it in hard.to.reach places for mowing.
  • Universality. The lawn mower is equipped with a knot to change working elements directly during the operation of the unit.
  • Constructive simplicity that allows you to use a braid for a long time without frequent tuning.
See also  How to put the mixer in the drill

These, other positive characteristics give customers confidence that when purchasing a trimmer for grass, make the right choice.

Gasoline for the preparation of the mixture

Gasoline requirements for the preparation of the mixture are extremely high, t.to. He is its basis. The first thing that should not be done is to look for places where you can buy fuel cheaper (refueling without name, etc.D.), because in the end, all the apparent savings in several dozen can be eaten by an expensive engine repair, which is disabled by poor.quality fuel.

Using cheap gasoline with a reduced octane number, the user thereby increases the load on the unit. Its wear occurs much faster, the resource decreases, moreover, in the proportion not one to one, but much more

The second one should remember is to use only fresh gasoline for the base of the mixture. Many in the country or in the garage have fuel reserves that stand there up to six months, waiting in the wings. Fuel, evaporating, enters into a chemical reaction with the surface of the canister (especially plastic), thereby acquiring new, not at all useful properties for ICE. If the gas was stood in the canister for a month and a half, it is better to pour it into the fuel tank, where, having mixed with the total volume of more fresh gasoline, it will not cause any harm to the engine of the machine. Two.stroke ICE are more sensitive in this regard. That is why manufacturers recommend using only the highest quality fuel.

As for the octane number, there are spores of specialists, what kind of gasoline to pour into a trimmer for the grass, they still do not subside. Most manufacturers recommend pouring a high-octane gasoline of the 92nd brand into the fuel system in the fuel system. True, there is one small reservation, quite often the instructions indicate the wording of “not lower than the 92nd”, and this leaves the space for guesses, which gasoline to use.

Of course, the performance (efficiency) of 95th gasoline is slightly higher than that of the 92nd. The latter, in turn, is the heir to the Soviet 80th, on which many equipment worked. But having higher energy efficiency, the 95th is fraught with some features. For example, it is more suitable for modern car models, while ICEs installed in garden equipment are far from some constructive innovations, their structure remains practically unchanged for decades. For a two-stroke gasoline engine installed in most modern trimmers, it will be enough to fill in gasoline of the 92nd brand, purchased on a proven refueling network.

It is best to look for options without additives with the markings “Eco”, “Ecto”, t.to. For clear work, you need a clean gasoline base. Adds the mixture with additives.

Is 95 gasoline is needed for optimal work, the question is rather a philosophical, and there is no specific answer for it. It is enough to remember that in the tortures and recommendations it is rare quite rarely, and this already says a lot. In addition, they are poured, usually, at their own peril and risk, wanting to improve the characteristics. If for the sake of the experiment you want to change the 92nd gasoline to the 95th, it is important to remember the consequences in the form of increased wear, unstable operation of the power unit and fails of its individual nodes. Of course, none of the above may occur, but the probability, in the event of the admission limits, is extremely increasing.

Redverg Basic GB52 gasoline trimmer

The Redverg Basic GB52 gasoline trimmer is designed for household use. Ergonomic bicycle handle with cast mount provides comfortable work with the tool. A coil with a fishing line is used to mow grass, and a 3-bladed disk 255×25.4 for a strain of thickets is used.

Trimmer for grass gasoline Redverg RD-GB243 is designed to work with grass and small shrubs. With it, the operator will be able to quickly and easily put the lawn of small or medium area in order. Comfort and safety during work. this is what the manufacturer first turned to. The ergonomic bicycle handle gives the master the opportunity to sensitively control the direction of movement of technology and achieve impressive results of any work.

See also  How to extend the line on a trimmer

The container should be tightly closed during storage. Fuel should be stored in a cool place, in a place where the sun does not penetrate. Remember that with prolonged storage of a mixture, the oil lifts and loses its properties.

The rules for filling the mixture in different engines

All of the above is relevant for two.stroke engines. In the case of four.stroke engines, dilute and mix nothing. gasoline is poured into the fuel tank, and oil. into the crankcase. It is important to know that you can not add oil intended for a four.stroke engine or for a liquid cooling system with a two.stroke engine. Otherwise, the entire piston system will be disabled or a strong overheating will occur.

dilute, gasoline, motorcycle, poured, trimmer

Important! For the first refueling of the four.stroke engine, the oil in a special tank can be poured no more than 90 ml.

Make Car Fuel as EASY as Coffee Step by Step Instructions Also make Ethanol Fuel Legally 1080HD

How to dilute gasoline with oil for a trimmer for grass. step.by.step instructions

Fuel mixing occurs taking into account special proportions.

If you dilute the fuel mixture with an insufficient amount of lubricant, this will lead to the rapid wear of the parts of the lawn mower

dilute, gasoline, motorcycle, poured, trimmer

The optimal ratio of oil and gasoline can be viewed in the instructions for the trimmer. As a rule, it is equal to 1:50, 1:40 or 1:25.

It will be forbidden to dilute gasoline with a lubricant component in a suitable container: to do this immediately in the fuel tank is prohibited. If you ignore this rule, the work of the motor can be unstable, as a result of which the tool will quickly fail. To dilute the fuel mixture, do not use plastic canists or bottles, since gasoline is able to dissolve this synthetic material. Fuel mixing order:

  • Pour a liter of gasoline into the container (optimally. metal canister).
  • Add half the necessary oil proportion.
  • Mix the liquid thoroughly, away from sources of open fire.
  • Pour the rest of the lubricant into the container and mix the mixture again.
  • Pour fuel into the fuel tank of a trimmer for grass.

Work should be carried out by wearing a respirator and rubber gloves. For the convenience of transfusion, you can use the watering can. The finished mixture should not be stored for more than 3 months, it is better to dilute exactly as many fuel as you need for the work planned in the near future. Mnight mixing oil with gasoline, be sure to choose high.quality, buy it better at proven gas stations.

Proportions of oils and fuel

Calculation of the ratio of ingredients for preparing a gas station for grass should take place taking into account the recommendations on the packaging from the oil. The standard proportion is 1:50. Any quality oil for two.stroke engines is allowed to use.

Selection of gasoline for a trimmer for grass

For some reason, everyone prefers to choose a brand of gasoline for motorcycles at their discretion. This is an erroneous approach, because, first of all, it is necessary to carefully study the instructions where the manufacturer’s recommendations for the choice of fuel are given. But this is also not a guarantee, since unearthly fuel can be sold under different brands (which differ in many manufacturers), which are significantly different in composition. Therefore, it is necessary to focus precisely on the main characteristics in order to choose gasoline for a certain model of a trimmer for grass.

Manufacturers of benzo-tools recommend using AI-92 gasoline brand for work, but for more expensive types you will need fuel with a higher octane number-AI-95. Any brands, in the marking of which the number 90 and less appear, is not suitable for benzos, since they lead to rapid wear. The problem develops due to unscrupulous fuel manufacturers, which are sold under the guise of 92nd a completely different brand. The following situation develops:

  • The passport for gasoline equipment has a recommendation for the use of gasoline with an octane number of at least 92;
  • The conscientious owner goes to a gas station, where the lowest price and with a clear conscience floods such a fuel in a motorcycle;
  • As a result, the service life is reduced, since often under the guise of AI-92 AI-80 and AI-76 is sold.

To avoid such a situation, you need to select one gas station, where the proven gasoline is sold (this can be determined by the reviews of regular customers). It is also important where to fill the fuel after the purchase. for this you need to use only metal containers (plastic. prohibited).

The option is preferred when it is possible to buy gasoline for a trimmer for high.cleaning herb specifically for garden equipment. Then you can be confident in its quality and protection against fakes.

See also  How to lubricate grass trimmer gearbox

How much oil per 1 liter of gasoline is necessary for a lawn mower or chainsaw

All two.stroke engines operate on the fuel mixture of gasoline and oil. The fuel enters the cylinder, burns there, creating a working effort on the piston, and that part of the mixture that did not have time to ignite, lubricates the moving parts of the piston group.

When compiling a fuel mixture for a lawn mower or a chainsaw, it is necessary to calculate how much oil is needed per liter of gasoline, based not only from a standard proportion, but also from which brand of gasoline and oil is used. In the case of two.stroke engines, it is very important.

For trimmers, a special two.stroke oil is made, on the package of which there should be a note “2t”. Car, and even more so, transmission oil is strictly prohibited. Two.stroke oil in three types is produced:

It all depends on what substances make up the oil base. Mineral oil is the cheapest and unreliable. Its use is justified only in household class trimmers, which work for 30-60 minutes a day with large interruptions. Most manufacturers of motorcycles of this level indicate that TS-W3 class oil is suitable for the engine. This means that you can use mineral, synthetic and semi.synthetic oil 2t.

It is advisable to buy only those grades of oil that the manufacturer recommends for a professional class motorcycle. This is usually semi.synthetics and synthetics with special additives.

Manufacturers mark the oil in letters:

  • ? That. for two.stroke engines with a volume of up to 50 cubic centimeters;
  • ? TV. for engines 50. 200 cubic centimeters;
  • ? TS. for engines of motorcycles, snowmobiles, etc.D.

In motorcycles, if the type of oil is not indicated in the instructions, you can fill in all three modifications. How much oil is added to the fuel of the trimmer for grass depends on the brand of the tool and the quality of gasoline. Also, on the packaging with butter, the letters FA, FB, FC, etc. may occur.D. They show the level of smoke. The closer the second letter to the beginning of the alphabet, the more smoke stands out during combustion. As a rule, high.quality oil has very little. This indicator does not affect the choice of oil.

important than the inscriptions “Self Mix” and “Pre Mix”. The first phrase means that the oil dissolves independently, and the container with the second mixture must be shaken several times.

If the manufacturer’s instructions do not indicate which gasoline to use, then it is necessary to stop at AI-92. If it is recommended to fill in AI-95, then do not use other brands of gasoline.

Some users are sure that if you add oil to gasoline for the fuel mixture more than necessary, it will benefit. This is not true. Not burned oil is not excreted from the engine with exhaust gases, but will settle inside in the form of soot. This plaque threatens the integrity of the piston. If you use the mixture with an excess of oil regularly, then the trimmer for the grass will be greatly smoked, and the drop in power is inevitable.

With a lack of oil, the trimmer for the grass will overheat, the piston rings will be destroyed and the piston jams. If the oil deficiency is insignificant, then the trimmer for the grass will work 30. 40% less than the resource. If the lubricant is not enough more than 20%, then the motor will jam after 20. 30 minutes of intensive work. Each instructions for the trimmer have proportions on how to dilute the fuel mixture. This is usually 1:25. 1:40 or 1:50.

Related Posts

| Denial of responsibility | Contacts |RSS