How to cut the baguette correctly. Fire, water and brass partition.

How to cut a ceiling plinth at 45 degrees

The measurements needed to trim the ceiling baseboard should be taken in a special way To determine and mark the inside corner, the length should be measured from the corner itself. To mark an outer corner, remember that the skirting boards will protrude into the premises by a distance equal to their width.

It is not desirable to fix the skirting boards before their exact position is measured and the mating skirting board is cut. Only when the two mating strips are perfectly aligned in the corner can you begin to mount and fasten them. If you are working with polyurethane or wooden skirting boards, defects and flaws can be corrected with a file or file. To fit the product of foam plastic, you must arm yourself with a sharp knife.

If even after finishing plinths remain even a small gap, do not rush to upset. it is not difficult to patch it with an ordinary putty.

It is not so difficult to cut accurately and neatly a ceiling plinth. But to acquire at least a small skill, first try to practice on small blanks.

Ceiling plinth is an original decorative element, it decorates the room and gives it sophistication. Hides all the errors in the corners of the ceiling connection to the walls, and hides such a nuisance as a crack in the corners.

Cutting off the corner of a ceiling plinth with a wire cutter

The main tool for cutting ceiling mouldings at an angle is the plier. Its design is simple, it is a kind of tray made of wood, metal or plastic with special grooves that guide the blade of a hacksaw at a certain angle.

With a standard tool, you can cut the product at angles of 45, 60, 90 degrees When cutting ceiling ties, the trim in 45 and 90 degrees is mainly used

Begin at the inside corners. To understand how to cut the correct corner of the ceiling plinth, to begin with, put it to the inner corner of the room and visually determine the line to trim the cut

Pay attention that the bottom, the edge that is fastened to the wall, always stays longer

Then we put the ledge in our joinery, so that the edge that will be fastened to the ceiling is at the bottom. We set its end at the desired angle, in this case 45°, fix it, and with smooth movements cut off the unwanted part.

In this way, we will get the correct cut of the ceiling moulding for the inside corner.

To cut the outer one, you should perform the same actions, only the direction of the cut will be different. When cutting, please note that, unlike the inner corner, the outer corner should leave longer the edge that is glued to the ceiling. Thus, for the right side the mode from right to left, and for the left side. from left to right.

How to make a proper cut without a chisel

So, we figured out how to cut the corner on the ceiling plinth using a wire cutter. But what to do if you don’t have such a tool at hand, and you don’t want to buy it in order to glue a molding in one room? There is a way out.

Let’s consider how to properly cut the corner of the baseboard without using a guide tool.

To do this, put a ceiling batten in the corner and use a pencil to draw a mark on the ceiling along the batten line. Do it on both sides, left and right. As a result on the ceiling we will have an intersection of two lines.

See also  How to wind the grass trimmer reel correctly

We transfer the point of intersection on the battens. After that we put them on a flat surface, as well as in a jig, and cut off unnecessary part. When cutting the fillet, take into account the rules that are used when cutting ceiling dumbbells in the joinery fixture.

The same way you can cut the outer corner. Only it is necessary to draw the lines already on the wall. Here we have figured out how to cut the corner on the baseboard without the use of a jigsaw.

Ways to cut corners of the baguette

The problem of cutting the corner connection of decorative cornices is not the difficulty of cutting correctly at an angle of 90 or 45 degrees, but the fact that mostly the corners of the room are curved, and do not have 90°. Therefore, you have to contrive, caulk the gaps with putty, liquid nails, silicone or trim by hand.

The use of decorative corners

The easiest, but also the most expensive way to cut the cornice for the ceiling. the use of decorative inserts. This method is expensive because we have to buy additional elements.

But there are some advantages to this option:

Decorative inserts for ceiling plinths (including flexible) on their purpose are divided into:

Photo of products designed to join the ceiling planks of the baguette

Understand how to cut the corner of the baseboard for this method is not difficult. In this case, the cornice for the ceiling is cut strictly at an angle of 90°. And, as you can understand from the photo below, glued against the previously glued corner.

The easiest way to decorate a corner using a corner joint for ceiling ties

Cutting off the corner of the ceiling plinth with the use of a jigsaw

The main tool for cutting ceiling cornices at an angle is the plier. Its design is simple, it is a kind of tray of wood, metal or plastic with special grooves that guide the blade of the hacksaw at a certain angle.

Photo of a tool that makes trimming ceiling baguettes simple and easy

We start with the inside corners. To understand how to cut the right corner of the ceiling plinth, for starters, attach it to the inner corner of the room and visually determine the line for trimming the cut. Note that the bottom, the edge that is attached to the wall, always stays longer.

Next, we put the ledge in our joinery so that the edge that will be attached to the ceiling is at the bottom. Its end is set at the desired angle, in this case 45 °, fix it, and with smooth movements cut off the unwanted part.

This way we get the right cut of the ceiling cornice for the inside corner.

Using the techniques shown in the photo, you will never make the mistake of trimming the dumbbell

Please note! If you stand facing the corner, you can divide it into right hand and left hand. So, the right inside corner is cut from left to right, the left, on the contrary, from right to left.

Tip! Do not allow excessive pressure or sudden movements when cutting. This can cause damage to the edge of the cut.

To cut the outer, it is necessary to carry out the same actions, only the direction of the cut will be different. When cutting, you should take into account that, unlike the inner corner, in the outer corner should remain longer the edge that is glued to the ceiling. So for the right side the mode from right to left and for the left side from left to right.

Note! The gap from the incorrect trimming ceiling cornices on the inner corner can be easily sealed, and seal it so that visible such a defect will not be. With the outer corner, you can not allow such oversights, as such a defect is almost impossible to fix. If the outer corner does not have a 90 °, then, first of all, cut the baguettes in a jig, and then fit them directly on site with a knife on drywall.

How to make a right cut without a chisel

So, we figured out how to cut the corner on the ceiling skirting board using a plank knife. But what to do if you don’t have such a tool at hand, and you don’t want to buy it in order to glue a baguette in one room? There is a way out.

See also  How to correctly assemble blades on a cultivator

Consider how to properly cut the corner of the baseboard without using a guide tool.

To do this, we put a ceiling batten in the corner and use a pencil to draw a mark on the ceiling along the batten line. Do it on both sides, left and right. As a result, on the ceiling we will have an intersection of two lines.

Marking the ceiling tiles for trimming without the joiner

Mark the crossing point on the dumbbells. Then put them on a flat surface, just like in a jig, and cut off the unnecessary part. Cutting off the fillet, take into account the rules that are used when cutting ceiling dumbbells in the joinery fixture.

Trimming ceiling molding without using a pitchfork

In the same way you can cut the outer. Only to draw lines already have to be on the wall. Here we are, and we figured out how to cut the corner on the baseboard without using a plier.

Note! To make a correct cut of the ceiling-tile without the use of a hook, it is very important not to make a mistake with the marking, and cut unnecessary part of the product strictly vertically. If you do not adhere to these rules, then at the junction of ceiling baguettes in the corner can create a large gap. Tip! Use this method only when cutting corners on foam and polyurethane ceiling skirting boards. If you use it on wooden or plastic mouldings, there is a great chance of damaging the product.

baguette, correctly, water, part

Tools you will need for trimming the baseboard

When cutting a skirting board, it is important to take into account the material of the skirting board for the ceiling. If the plinth is plastic, then you can’t do without a hacksaw for metal. Wooden skirting boards are cut with a fine wood saw. Well, if you need to glue a foam or polyurethane baguette for the ceiling, then a simple sharp knife will suffice, a gypsum board or a stationery knife is ideal for this case.

In addition to cutting tools, you may also need tools like these:

Note! Only use tools that are in good working order. The cutting tool must be sharp, with fine, dense jagged edges. This will not only achieve a perfectly flat and smooth cut, but also protect against possible damage to the product.

Response to the post “The price of renovation in a one-bedroom.

I did 28 meters in a one-bedroom crumb. Was able to accept completely finished in January.

It went like this. All stripped to the ceiling and bricks, to redo the approved and coordinated redevelopment with the design project.

Different were counted. For example, one foreman said 150002500 (roughing materials) per square meter, the other plus or minus a kilometer in a million with the net.

As a result, decided to do through a firm. They calculated an estimate of 410 without roughing 15% on top of contingencies (happened as expected). The rough estimate was 200-250. Bottom line. I paid 715 on all the estimates with rough materials. I bought my own quartz vinyl, ceramic tiles, outlets, light bulbs, plumbing

I was very pleased, got exactly what I wanted. I will not overload the answer, but if you want. I will show you pics of the was / is

We hope that after reading the above tips, you will understand how to properly cut the baguettes and how to then dock them to get the most reliable and neat joints. In mastering the described technique will help you video in this article, and if after watching it there are any questions, you can always ask them in the Комментарии и мнения владельцев and get a comprehensive answer!

baguette, correctly, water, part

Installing the baguettes and skirting boards gives the repair a finished and neat appearance, but only if the trimming is done correctly and all the joints converge perfectly straight. Different tools and techniques are used for trimming, making the job easier, but it’s also important to consider a lot of nuances, which we’re going to talk about today.

How to carve a corner with a jigsaw

Chisel. joiner’s tool, with which you can cut any material at an angle of 45 and 90 degrees. The chair can be made of wood, plastic or iron. Even the simplest device has openings for a hacksaw, the more expensive models even have a swivel mechanism.

See also  Why an electric screwdriver won't tighten. Replacement tapered type of part

The principle of the jigsaw is very simple. Place the slat in the groove, press it down and cut through the side holes. The end result is a cut at the desired angle.

  • Measure.
  • Insert the skirting board into the groove of the jig saw, facing upwards.
  • Press with your hand on the plank, but not too hard (if the skirting board is made of foam plastic, it is easy to break it).
  • Insert the hacksaw at a 45 degree angle into the hole in the jigsaw and make the cut
  • Mirror cut the second piece in the same way. It turns out the formed inner corner.

Tip! You can cut the skirting boards with a metal hacksaw, but if the baguette is narrow, it is better to use a construction knife, it makes the cut more even.

Cutting the outer corner is just as easy. Step by step instructions:

baguette, correctly, water, part
  • On the underside of the skirting board, mark the correct length, but its edge should protrude a little.
  • We put a plank in a plane at an angle of 45 degrees and through the holes we make the cut.
  • In a mirror reflection we cut the second slat.
  • Prepared elements we attach to the wall. If everything is even, then we glue, and if there are flaws, then simply remove them with a sharp knife.

If you have to work with a wire cutter for the first time, it is better to pre-practice on extra pieces.

Selection of tools for cutting ceiling baseboards

In order to cut a ceiling plinth properly and accurately, it is necessary to use a proper cutting tool. It is chosen depending on the material from which the bumpers are made:

    Styrofoam. Characterized by low strength and costs relatively inexpensive, and therefore foam models are becoming more and more popular. Their strength does not particularly affect the performance, because usually the ceiling plinth is not subjected to mechanical stresses. An ordinary office knife is suitable for cutting.

It can be purchased in a construction store or make their own hands according to these instructions:

    Three 5015 cm planks are nailed with a long edge into the shape of a three-sided, rectangular box. Pay attention, between the side boards and the cross-plank an angle of 90 degrees has to be observed.

To work with this homemade device was convenient and safe, planks should be well sanded before fastening.

How to trim a ceiling plinth correctly. Important little things

Measurements needed to trim the skirting board on the ceiling, should be done in a special way. To determine and mark the inside corner, the length must be measured from the corner itself. When marking the outer corner, remember that the skirting boards will protrude into the room by a distance equal to their width.

It is not desirable to fasten the skirting boards before their exact position is tried on and the counter skirting is cut. Only when both skirting boards have perfectly joined in a corner can they be fitted and fastened. If the work is done with polyurethane or wood baseboards, defects and flaws can be corrected with a file or file. To fit the foam product, you should arm yourself with a sharp knife.

If even after finishing the skirting boards remains even a small gap, do not rush to upset. it is not difficult to seal it with an ordinary putty. To cut accurately and neatly a ceiling plinth is not that difficult. But in order to acquire at least a small skill, first try to practice on small workpieces.

Related Posts

| Denial of responsibility | Contacts |RSS