How to cut baguettes without a jointer. Installing the ceiling plinth with their own hands

How to cut a ceiling plinth in the corners without a chisel

Every beginner, who started the repair, sooner or later asks the question, how to cut the ceiling plinth in the corners without a plough. The scheme proposed in the article is perfect for the beginner, and for the experienced craftsman, so that beautiful flat skirting boards are a joy to the eye.

How to trim a ceiling plinth in the corners without a chisel

How to cut a skirting board with a utility plough

Chisel. a carpenter’s tool, which is a tray with slots. It allows you to cut ceiling skirting at the right angle.

If we talk about professional tools, they have a special swivel mechanism. This allows you to set the desired degree of angle. It is most convenient to use the chisel when the angle between the walls is perfectly straight.

How to cut a skirting board by means of a jig saw

The chisel is a carpentry tool, which is a tray with slots. It allows you to cut the ceiling skirting at the right angle.

If we talk about professional tools, they have a special swivel mechanism. This allows you to set the required degree of angle. It is most convenient to use a jig saw when the angle between the walls is perfectly straight.

Materials required

A set of tools for making an angled ceiling joint without using a jigsaw is not that big, and in principle no different from a set with a jigsaw. These tools are almost everyone’s home:

You can use an ordinary paper pencil with a hardness of HB or a construction pencil, if you have one available. You can buy this pencil in all hardware stores, and it’s within 50 to 100 dollars, depending on the manufacturer.

See also  How to make an impact screwdriver. Impact screwdriver from a starter motor with their own hands

Measuring tape and ruler you will need for accurate measurements and making straight lines, everyone in the house has them. Please note that without a ruler you will not be able to draw even lines for cutting corners by the first method.

A construction or office knife with interchangeable blades is an indispensable helper at home. Its cost, as well as a construction pencil, is low, and it is always available, it will give you the opportunity to cut easily and evenly the necessary segments, cut a corner or cut thin plates when fitting the connection. Some baseboards are made of material that is recommended to cut only with a knife, not with a hacksaw because of the softness of the material.

You will need a hacksaw only if the material from which the baguettes are made, it is recommended to cut only with it. The usual fine-toothed hacksaw will do.

Ceiling plinth must be chosen for both aesthetic and practical reasons. It should fit harmoniously into your design, cover the joints of the ceiling and walls, hide defects and irregularities. When choosing a molding, take into account the material it is made of. this affects the choice of trimming tool and glue for installation, as well as the type of coating on which the baseboard will be glued.

Block: 3/5 | Number of characters: 2560

Tips

Despite the fact that it is not so difficult to glue ceiling baseboards, there are tips that are worth heeding:

  • The walls must be clean, dust-free. Any dirt will reduce the adhesive properties of the base.
  • The underside of the skirting boards is better to make rough, as the smooth surface has a low quality of adhesion to the surface.
  • It is important to choose a quality adhesive with a good hold, especially for heavy baguettes. Also, do not use solvent adhesive for foam plinths, such a compound can ruin the material.
  • After attaching the ceiling skirting boards within a day should not be allowed draughts in the room, the glue must be well cured.
See also  How to make an air compressor from an air conditioner compressor

.

Using the wood joiner at home

The chisel is a simple tool that is a carpenter’s helper. With it, it is easy to cut blanks at any angle that is needed. Its construction is uncomplicated. a tray of wood, metal or plastic. This tray has special slots (placed vertically) for trimming at an angle of 90 or 45 degrees.

Some models have a more complex structure with the ability to cut at an angle of 60 degrees. For professional work there are special models, where the workpiece is fixed at any given angle.

The chisel is a simple but important tool

  • Hold the baguette and place it on the ceiling. In doing so, it is worth setting aside the required length. This workpiece is inserted in this tool in the position in which it will be placed on the ceiling. Pressing should be against the far wall of the jigsaw.
  • Hold the tack with your left hand. The hacksaw, or rather its blade, must be placed so as to create an angle of 45 degrees. The handle should be as close to the hand as possible.

Tip: To get a better orientation when filing the inside corner, start trimming from the front of the fillet. Where the cuts were made, in most cases, treatment with a file to fit both parts of the angle.

How to trim a skirting board correctly. Important trifles

The measurements needed to trim the skirting boards on the ceiling, should be made in a special way. To determine and mark the inside corner, the length must be measured from the corner itself. When marking the outer corner, it is essential to remember that the skirting board will protrude into the interior of the room at a distance equal to its width.

See also  How to attach the cabinet to the drywall. Drywall anchors

If even after finishing the skirting boards even a small gap remains, do not rush to get upset. it is not difficult to seal it with an ordinary putty. Trimming a ceiling plinth accurately and neatly is not that difficult. But in order to acquire at least a little skill, first try to practice on small billets.

Block: 4/4 | Number of characters: 1115

Wood

Wood ceiling plinths are different from their counterparts. The wood is heavy enough, which affects the weight of the product. Skirting boards end up quite dense, very resistant to mechanical damage and hard, which allows you not to be afraid of accidental deformation during installation or cutting.

To trim a wooden fillet, it is best to take a fine-toothed hacksaw designed specifically for fine work with this material. However, not a bad option would be a quality blade on metal.

Related Posts

| Denial of responsibility | Contacts |RSS