How to cut a ball brick with a corner grinder. Laser cutting

How to cut chamotum brick?

Previously, the question of cutting bricks did not arise, because it was simply cut with the help of a pick. But now there are a lot of construction tools that allows cutting blocks quickly and accurately.

During the cut of this building material, a lot of dust is formed, so you need to always use personal protective equipment: a respirator, fabric gloves, plastic glasses. According to safety regulations, all electrical equipment must have grounding.

To get an accurate and even cut, you need to apply the necessary marking to the processed object. The necessary dimensional lines are applied to the plane of brick with a pencil with a pencil with a ruler and a square.

Cutting with a gas tank

A special circular saw of an independent type equipped with a gasoline engine is called a gas tank. This tool has a large mass and size, so for piece cutting of ceramic brick, it is not very convenient. Cutting tool used in a gas tank can be two types: wheels or chains. Both types of equipment are made with diamond spraying.

The saw, equipped with a disk, resembles a corner grinder (only larger). When installing the circuit, the tool is similar to a chainsaw. Due to its power, such a saw is more suitable for cutting openings and niches in brickwork, as well as in dismantling. Benzorezoresis is able to cope with the walls of almost any thickness. A big plus is the equipment of this equipment for a forced water supply system to the cutting area, which eliminates dust.

Cutting brick corner grinder

When performing a small volume of cutting brick, a corner grinder is a good solution. It is recommended to use angular grinding machines with a capacity of 2 kW. But you should not take too powerful, because they are extremely bulky and heavy.

The most convenient for this are models in which it is possible to use circles with a diameter of 23 cm. The cutting equipment of smaller diameter is also suitable, but using it is not too convenient, t. to. The disk does not pass for the entire thickness of the block. The workpiece will need to be turned over, while the accuracy and quality of processing will suffer, the performance will significantly decrease.

Technically, the method of cutting bricks with a corner grinder does not represent much difficulties. But it is important to hold the tool correctly. It must have a reliable fixation, in which the cutting edge is strictly perpendicular to the processed surface. In an inexperienced person, it is unlikely that you can immediately make an even cut, so you should first practice. It is necessary to take into account the width of the cutting edge and the backlash of the tool.

Experts advise to use a special clamping bed for angular grinder to improve the quality of cutting. In this device, the workpiece is fixed in an individual recess, and the angular grinder is rigidly fixed on the lever. The fixed fastening of the brick block allows you to easily cut it along, across and at any angle. details on

brick, corner, grinder, laser

Diamond cutting brick

In order to obtain a flat cut surface without cracks and chips, diamond cutting brick is used. Such work is carried out by corner grinding, but using a special diamond cutting tool. Any work in which such equipment appears are considered a diamond sharp. The difference between these cutting elements is that they have diamond spraying on the working part.

For cutting brick blocks, it is better to use diamond discs, t. to. They ensure the safety of work and have a long service life. Use diamond cutting with a more powerful professional tool is economically impractical.

Manual tile cutter

When there is a need to cut thin pieces of facing brick, you can use a hand tile. It will be convenient when carrying out finishing work, when pieces of brick with non.standard dimensions and angles may be needed.

The use of tile cutters

With forceps you can give a brick an arbitrary figure shape: perform a bevel, rounding, etc. The tool is suitable for thin and painstaking work.

Cutting brick using a special machine

A specialized machine for cutting bricks is effective in case of large.scale work. It allows you to carry out all manipulations as quickly and efficiently as possible. Due to the presence of an irrigation system during processing on such a special machine, a minimum amount of brick dust is thrown into the surrounding air. But this equipment has a fairly high price, so its use for single work is unprofitable.

Some craftsmen make machines with their own hands. To do this, build a structure from a bed (support) and cutting equipment (circular saw, corner grinder). The equipment should be securely fixed and before starting work to control the serviceability.

How to cut furnace brick at home, so as not to redraw a pile of material

From the author: Hello, my dear readers. Very often, during the construction process, we have many small problems that need to be solved here and now. If you are faced with an exclusive type of masonry, then the question of how to cut a stove brick at home may appear by itself.

Why cut brick

Quite often, amateur masons are faced with the problem of changing the classic sizes of a particular type of brick. Few resort to generally accepted standards and try to find their methods that allow you to make a small.sized block from an ordinary block.

The reason for the need for such actions is the features of masonry. Repeatedly, I resorted to the most various cutting methods during the construction process due to the fact that it was necessary to make a beautiful joint, correctly finish the side, lay out the corner, fill in the missing or dropped part.

Having gained experience, I identified several basic ways to cut a brick with my own hands:

  • using improvised materials,
  • Using a specialized, manual, chantsex tool,
  • Auxiliary electrical equipment,
  • intended for this technique.

Each of them occupied its niche in the modern construction industry market. Let’s look at each of them in more detail.

Improvised materials

The right equipment is not always at hand, which will help to do work better. However, if your hands grow from the right place, you can without much effort to solve the problem on the spot.

I have repeatedly had to break stones right at the place of work, as time was running out, and get bulky equipment in order to make the right one only one copy, there is no special meaning. If you have never done this before, be sure that the first time it will not work.

So, if there was nothing suitable nearby, you should arm yourself with an ordinary hammer and chisel. If the second is also not, it will be enough and the first. It is very important that there is no mechanism for extracting nails on the reverse side. Better let it be small than big. You can not even think about repulsive with a sledgehammer. This will simply ruin everything, although I will not say that I have not seen such rather non.unique events.

Separate the part you need with light blows and use further as intended. Be prepared for the fact that you can ruin a few pieces, because this is a rather subtle business that requires accuracy.

Of course, not everything depends on you. It is possible that simply poor.quality material, which has now divided enough, fell into your hands.

Shantsian instrument

The availability of more serious technology that allows you to perform the necessary manipulations with bricks is not always affordable. If you do not operate with a large budget and you can afford only simple, even primitive devices, do not despair. With their help, you can also do everything quickly and efficiently.

The first tool was called “Kirka”. They are completely different sizes and are used in different ways. The reverse side of the hammer, which was mentioned in the previous paragraph, performs precisely these functions, however, such a chancery instrument will separately bring an order of magnitude more benefit than attached to another.

You need to use it carefully, light, but accurate blows in the required area. The force that will need to be attached should not smash the brick to shreds, remember this.

The second gadget that I would recommend is special chisels for cutting bricks. Their size and shape allows you to complete the task up to millimeters up to millimeters.

The disadvantage of such techniques is that you will have to make a corner chip with great difficulty, and if this even comes out, then its evenness will clearly be limp to limp. Therefore, the normal joint will not work, and all aesthetics will disappear where it is not clear where.

See also  Grinding a bar with their own hands. Professional sanding services

Cutting Brick and Concrete with a Grinder Masonry Wheel

There was one familiar grandfather in my century, who was considered the best of the best. Like, he himself laid out a stove in two floors in three days. And exactly everything was, and high.quality. I once had to work with him, well, of course, when it came to the end of the side, I had to break off a piece. For this, the grandfather had a special small, homemade chirus.

I remember how he took one brick and struck. Naturally, the part disappeared, but this was not enough. He struck another blow, and from one we got three, and not one of them came up in size. So he spoiled about 3-4 pieces per corner.

I suggested using a cutting device, for which I heard offensive expressions. In the end, at the end of the work, the customer was dumbfounded, how much the material was spoiled. I told all this to the fact that be prepared for a huge number of waste materials, unless, of course, you understand that the use of more new methods is more effective.

Standard electrical equipment

Everyone who plans to start repairs or construction, must necessarily have a standard electrical equipment that will help to facilitate almost every aspect of work. The drill and electrician will not help us, but you will have to resort to the help of an angular grinding machine. The people are called a corner grinder, if you do not immediately understand what it is about.

I’ll tell you about several aspects that you need to know for sure:

  • Choose the right disk. To work with materials based on concrete, you need to use specialized diamond discs. Do not worry, they are not made of diamonds completely, and there are not millions. All that distinguishes them is diamond spraying, which allows you to carry out work without damage to the tool,
  • Be prepared for cleaning. Stoves, pipes and other designs that are laid out of heat.resistant bricks are mostly indoors. It should be remembered that when working with a corner grinder, a lot of dust is formed. So either be ready to clean for a long time, or go outside and do your job there,
  • Do not forget about safety precautions. It is worth remembering that the wearing protective gloves and glasses will help keep your health.

How and how to cut a brick: an overview of the tool

During the construction of brick walls, during the arrangement of furnaces, as well as during facing work, building materials of non.standard forms and dimensions are often required quite often. Therefore, every employee who is dealing with similar works should know exactly how to cut a brick and how to correctly carry out this operation. In this article we will talk about the devices that will help in this matter.

Not so long ago, professional builders and amateurs did not even ask the question of how to cut a brick. They used the usual kirochka and the cutting method, which is not distinguished by a high level of complexity.

The process of cutting brick using a pick or combined cell is as follows:

  • It is necessary to take a unit of building materials in the left hand;
  • After that, you need to apply a fishing line for a trimmer of a split using a tool on all faces of the product;
  • At the end, apply a sharp jerky blow to the edge of the product, while the chirus and the surface of the brick should form a right angle.

This method has some disadvantages:

  • low accuracy;
  • The surface of the formed face is uneven, so it has to be hidden inside the masonry, and this is impossible in some cases;
  • you can not split the brick from a different angle except for the direct.

But, time has passed, and now there are new construction tools that can be used for these purposes. They make the process more convenient and accurate, plus everything significantly reduce the time. In addition, the formed faces of products have a flat surface.

Now there is a fairly fair question than to cut silicate or chamotis brick. Modern construction specialists use the following tools for this purpose:

CHAMOT production

Clay brick is produced according to GOST 390-69. Available in two versions: 25012365 mm and 23011365 mm. It is characterized by a fine.grained structure.

Blocks contain 70% refractory clay, 30% coke and graphite powder. The weight of the block depends on its size and structure; It is available weighing from 2.5 to 6 kg.

Withstands temperatures from 1000 to 1800 degrees. He does not respond to sharp temperature changes. Experts use this type of building material for the construction of household furnaces.

brick, corner, grinder, laser

Distinctive features of refractory blocks:

Manufacturers produce different types of refractory bricks. They differ in weight, size, shape, as well as the degree of porosity and manufacturing technology. The following varieties are available for sale:

These types of chamotum layer allow you to build any structure.

Given the composition and degree of porosity, bricks are made:

These properties of refractory bricks help make the right choice of blocks for construction.

By the method of layering, they are divided into the following types of brick furnaces:

Necessary tools

Cutting brick is performed using an angular grinder, a stone.cutting machine or a gasoline cutter. In addition, a square and a construction pencil will come in handy.

Production of blanks

Cutting a brick with a corner grinder is necessary in small.scale production. Line or brigades of builders to buy specialized equipment unprofitable and have to use more universal.

For cutting bricks with a corner grinder, you need a power tool for a circle with a diameter of 230 mm.

For cutting bricks with a corner grinder, it is better to use diamond discs.

When using a corner grinder under the 180th circle, cutting a brick to the full thickness will not work, you will have to turn it over, which significantly reduces the performance and convenience of work, and you will not get an even cut over two passes.

Corner grinding grinding for cutting bricks should choose a fairly powerful. For a long tool for the tool and a comfortable speed of work, you need an angular grinder with a capacity of about 2 kW or more. Too powerful cars are not desirable, t. to. They, as a rule, have a sufficiently large mass and dimensions, which contributes to rapid fatigue when working with corner grinders and reduces the overall comfort of operation. It is convenient to finalize surfaces with a 125 mm angular grinder.

During the use of corner grinder, do not forget about safety precautions. Be sure to put on the goggles.

There are two main types of stone circles: abrasive and diamond. Perhaps the only advantage of the standard abrasive circle can be considered its relative cheapness. Cheapness is precisely relative, t. to. ordinary abrasive circles are subject to rapid wear and are subject to frequent replacement. They are also inconvenient in work, since when stinging such a circle, its diameter is constantly reduced, and it cuts to full depth only at the very beginning of use. Abrasive circles of different manufacturers can differ greatly in quality and service life. As a rule, a good abrasive circle on stone has double reinforcement and a thickness of 2.5-3 mm. It is dangerous to work with an abrasive circle, t. to. It is more susceptible to deformations and destruction.

The diamond circle is preferable, it retains a constant diameter during operation. One diamond circle of good quality can survive dozens of ordinary abrasive circles. The diamond disk has a strong steel base, as a result of which the probability of its destruction is negligible.

Kolka and Teska Brick: a. the right speaker across; b. irregular speaker across; B. Kolka along; g. working position with Teske; D. working position with Kolka.

There are several types of such circles. The simplest circles with a continuous edge are cheaper than the rest, but have significant disadvantages. In the process, they are very hot, which can cause emergency discharge of disk. To avoid this, it is necessary to arrange breaks in work. The service life of such discs is the lowest. The advantage of the continuous edge of the disk is the high quality of the cut surface without bullying and dyeing.

The most common diamond circles are segment. Their cutting edge is divided by radial cuts into separate sections. This design allows you to effectively remove the sludge and ventilate the cutting area. This is a good choice to cut a brick with a corner grinder. They are usually used for dry cutting. When water supply, segment grooves are clogged with wet cutting products, which worsens the properties of the disk.

The best option will still be a turbocharged disk. It has a toothed surface that gives the disc of higher strength and rigidity. The location of the teeth on the edge of the disk in a spiral creates the effect of the centrifugal pump, which is the best possible to divert wet or dry sludge. Discs of this design are most durable and cut brick and masonry stones of any type.

Before cutting a brick with a corner grinder, you must first mark. This is done by a building pencil and a square. It is necessary to take into account the thickness of the disk and the backlash on the spindle of the corner grinder. If you draw a fishing line for a trimmer simply in the right size, most likely you will not succeed. Cut brick will be shorter than the required size by 1.5-2 mm.

brick, corner, grinder, laser

See also  angle grinder with adjustable speed

How to Easily Cut Bricks With a Portable Angle Grinder

Tool cutting

It will go much faster, more precisely and better, if you use a tool for cutting brick. His choice is not too extensive: usually used an angle grinding machine (corner grinder), benzores or a special brick cutting machine for this.

Without a construction square and pencil for applying marking, one cannot do in these cases. In addition, you will need personal protective equipment, since the cutting process is accompanied by the formation of a large amount of dust and small fragments. These are gloves, glasses and a respiratory mask.

Corner grinder

Than to cut the brick if you need a small amount of non.standard stones?

For this purpose, an angular grinding machine is best suited, which is popularly called a corner grinder. Unlike equipment, which will be discussed below, almost every home master has such an tool.

Advice. It is recommended to use a corner grinder with a capacity of about 2 kW. A less powerful tool may not cope with the task, but it’s hard to work too powerful.

A disk for cutting brick installed on the machine can be of two types:

  • Abrasive. inexpensive, but not too practical. It is quickly “erased” and can deform or crack during the saw process, which will affect the quality of the cut and safety of the master.

Abrasive cutting circle

  • Diamond. durable steel disk with diamond spraying is very reliable and durable. It is more suitable for this operation, as it easily cuts brick, making an even and neat cut. But its price is much higher than abrasive.

In any case, the optimal disk diameter is 23 cm. A smaller circle will not break the brick over the entire thickness, so it will have to turn it over in the process. But too big circles are not so convenient to work.

Diamond discs, in turn, differ in the type of edges and are: there are:

  • With a solid edge. The cheapest of analogues give an even surface on the cut. But heat up during work and wear out faster.
  • With a gear turbocharged edge. The cloves on it are located in a spiral, so the dust and other waste is well diverted from the working area. Such discs can be used for dry and humid cutting, they have the longest service life and the best working characteristics.
  • With a segment edge. In such disks, cuts are made along the edge, dividing the working plane into separate sections. The section of the cut during operation with such a disk is constantly ventilated, so it heats up slower. But with wet cutting, there is a risk of waste flipping in slots, so it is used mainly for dry cutting.

How to cut bricks, and which disk is up to you to decide. Now you know about the features of any cutting nozzle.

You just need to remember that it is necessary to cut not exactly along the marking line, but a little retreating from it so that the marking remains “in the body” of the part you need. Otherwise, due to the backlash of the instrument and thickness of the cutting part of the disk, it will turn out less than the required size.

Holding a corner grinder on weight, it is difficult to make a quality cut. It is better to fix it and brick in a clamping bed. With its help, you can make neat cuts not only along or across the brick, but also from any angle.

A special bed for corner grinding faces will facilitate the work

It is very important when performing such work do not forget about safety precautions.

The instruction requires the following points:

  • The tool must be held with two hands so that when the reverse it does not break out of his hands and does not injure you or to others. This requirement will also ensure a higher cut accuracy.

During work, a stable position and the correct capture of the tool are very important

  • An electric supply cable should be at the maximum possible distance from the working area in order to avoid cutting it or wrapping a disk with all the ensuing negative consequences.
  • It is possible to release an angular grinder from the hands and put on the ground or other surface only after the disk rotation is completely stopped.
  • The cutting circle must be closed with a protective casing.

You can’t use a corner grinder without a casing

Advice. To reduce dust formation, you can pour water into the working area when cutting bricks.

Brick cutting machine

Special brick cutting machines are expensive, it does not make sense to buy them for one.time work. This complex equipment is intended for those whose activities are related to masonry work.

It consists of the following nodes and elements:

  • Metal bed;
  • Power unit with an electric motor and a diamond circle;
  • Brick or stone fixation system;
  • Most models are also equipped with a water supply system to the sawing zone.

Dakar plus brick cutting machine

Such equipment allows you to quickly and with high accuracy perform cuts of any complexity. At the same time, the master is always visible to the process of cutting, he can control it.

And the irrigation system minimizes the amount of brick dust thrown into the air, doing the work as comfortable and safe as possible.

How to cut a brick using this machine?

  • You need to mark it and install it in the working area, fixing in the right position;
  • The cutting part of the tool is lowered to the working area and focused on marking;
  • Then turn on the engine and set up rotation speed, after which they cut.

In the photo. the process of cutting brick on the machine

Correct manual cutting

Prior to the appearance of an electric tool, the masters-toking had to chop brick with manual devices. Cutting was carried out with kirki or kelma.

In order to achieve even surfaces of the material as a result of processing, you should do the grooves of the spin on all faces. Do this by applying light weak strokes with a small picking. When the groove is ready, a strong blow is delivered with a pick. It is important to keep the tool strictly vertically to avoid the split.

  • uneven edges of chips that require additional grinding;
  • The duration of the process (30-40 min.);
  • imperfect accuracy of the chip;
  • the inability to split a brick with a given angle for figure finishes.

Modern masters prefer to avoid manual cutting.

Tool cutting

It will go much faster, more precisely and better, if you use a tool for cutting brick. His choice is not too extensive: usually used an angle grinding machine (corner grinder), benzores or a special brick cutting machine for this.

Without a construction square and pencil for applying marking, one cannot do in these cases. In addition, you will need personal protective equipment, since the cutting process is accompanied by the formation of a large amount of dust and small fragments. These are gloves, glasses and a respiratory mask.

Corner grinder

Than to cut the brick if you need a small amount of non.standard stones?

For this purpose, an angular grinding machine is best suited, which is popularly called a corner grinder. Unlike equipment, which will be discussed below, almost every home master has such an tool.

Advice. It is recommended to use a corner grinder with a capacity of about 2 kW. A less powerful tool may not cope with the task, but it’s hard to work too powerful.

A disk for cutting brick installed on the machine can be of two types:

    Abrasive. inexpensive, but not too practical. It is quickly “erased” and can deform or crack during the saw process, which will affect the quality of the cut and safety of the master.

In any case, the optimal disk diameter is 23 cm. A smaller circle will not break the brick over the entire thickness, so it will have to turn it over in the process. But too big circles are not so convenient to work.

brick, corner, grinder, laser

Diamond discs, in turn, differ in the type of edges and are: there are:

  • With a solid edge. The cheapest of analogues give an even surface on the cut. But heat up during work and wear out faster.
  • With a gear turbocharged edge. The cloves on it are located in a spiral, so the dust and other waste is well diverted from the working area. Such discs can be used for dry and humid cutting, they have the longest service life and the best working characteristics.
  • With a segment edge. In such disks, cuts are made along the edge, dividing the working plane into separate sections. The section of the cut during operation with such a disk is constantly ventilated, so it heats up slower. But with wet cutting, there is a risk of waste flipping in slots, so it is used mainly for dry cutting.
See also  How to correctly sharpen a chainsaw chain on a machine

How to cut bricks, and which disk is up to you to decide. Now you know about the features of any cutting nozzle.

You just need to remember that it is necessary to cut not exactly along the marking line, but a little retreating from it so that the marking remains “in the body” of the part you need. Otherwise, due to the backlash of the instrument and thickness of the cutting part of the disk, it will turn out less than the required size.

Holding a corner grinder on weight, it is difficult to make a quality cut. It is better to fix it and brick in a clamping bed. With its help, you can make a neat cut not only along or across the brick, but also from any angle.

A special bed for corner grinding faces will facilitate the work

It is very important when performing such work do not forget about safety precautions.

The instruction requires the following points:

The tool must be held with two hands so that when the reverse it does not break out of his hands and does not injure you or to others. This requirement will also ensure a higher cut accuracy.

During work, a stable position and the correct capture of the tool are very important

  • An electric supply cable should be at the maximum possible distance from the working area in order to avoid cutting it or wrapping a disk with all the ensuing negative consequences.
  • It is possible to release an angular grinder from the hands and put on the ground or other surface only after the disk rotation is completely stopped.
  • The cutting circle must be closed with a protective casing. You can’t use a corner grinder without a casing

Brick cutting machine

Special brick cutting machines are expensive, it does not make sense to buy them for one.time work. This complex equipment is intended for those whose activities are related to masonry work.

It consists of the following nodes and elements:

  • Metal bed;
  • Power unit with an electric motor and a diamond circle;
  • Brick or stone fixation system;
  • Most models are also equipped with a water supply system to the sawing zone.

Such equipment allows you to quickly and with high accuracy will perform a cut of any complexity. At the same time, the master is always visible to the process of cutting, he can control it.

And the irrigation system minimizes the amount of brick dust thrown into the air, doing the work as comfortable and safe as possible.

How to cut a brick using this machine?

  • You need to mark it and install it in the working area, fixing in the right position;
  • The cutting part of the tool is lowered to the working area and focused on marking;
  • Then turn on the engine and set up rotation speed, after which they cut. In the photo. the process of cutting brick on the machine

Sometimes there is a need for cutting not individual bricks, but in cutting in brick laying of various niches, door and window openings. In such cases, the most effective tool will be a gas tank with which diamond cutting of brick walls is carried out.

Possessing great weight and considerable dimensions, it is not convenient for piece work, but indispensable for sawing masonry and dismantling work.

Benzorezer is, in fact, a circular saw with a gasoline engine, a cutting tool in which there can be a disk or a chain with diamond spraying. The saw with the disk looks like a large corner grinder, and with a chain. a chainsaw.

How and what to cut, chop brick? Step.by.step instructions

Sometimes in the process it is necessary to cut a brick, how and what to do in detail in this article.

Brick is a popular building material that managed to prove himself as a reliable, durable and durable.

Structures from it are able to withstand significant mechanical loads, negative effects of mechanical factors, conditions of extreme operation.

But to build a house from it, you will need a lot of time, money and effort.

Durable, dense material is not easy to process.

To cut it, cracking, special manual and electrical tools are used, which will be discussed later.

How and how to cut brick

To get two elements of the same or different shapes and size from one brick, you will have to work hard.

Professionals use specially designed tools to perform such operations, but amateurs will have to be content with what is at home.

Do not buy expensive equipment just in order to cut several elements when erecting a house?!

So, these are the tools can be used to process silicate or chamotis bricks:

  • chisel, combined cell, chirus, hammer;
  • Corner grinder, it is also an angular grinding machine;
  • benzores;
  • hacksaw for metal with special spraying;
  • electrician;
  • cutting machine;
  • Laser equipment.

The most advanced today is the last option.

Compact, mobile laser installation quickly, efficiently and easily cuts not only brick walls, but also a dense, durable monolith, suitable for processing concrete blocks and other building materials.

The principle of operation of the equipment is based on the use of gas discharge lasers.

Laser installations are quite expensive, so buying them for use at home is inappropriate.

Laser cutting services are provided by construction companies and repair teams.

When performing work, a number of nuances should be taken into account, for example, the presence of reinforcement in the laying of the reinforcement, the type of material, whether there is access to electricity and water, etc.D.

Among other popular power tools, with which you can cut this building material at home, the first place is a corner grinder is given.

Manual can be used, but they have to bother with them for a long time.

Why cut, chop brick

So, why in general stab or cut building materials?

Is it really so difficult to choose products of the right size from a wide range?

Different situations may occur at the construction site.

There is not enough half.brick to complete the row, the owner wants to decorate his house with elements of irregular shape.

Just cut it with a hacksaw.

To perform such ideas, an aggregate is necessary that can make a brick of any shape.

You can post building materials without problems at home, if you have the necessary devices at hand.

If in the end you get a product of the desired size and shape, you can easily lay a brick in a place intended for it, embody the original design or architectural idea.

How to cut, chop brick

Brick cutting can be carried out using a manual or electric tool.

Not so long ago, professional builders for processing this material and giving individual units of irregular shape used combined cell.

This method is available to everyone, but not without flaws.

So, for example, the disadvantages of this method of brick.ups include low accuracy, uneven, rough faces.

In addition, it is possible to chop building materials only at a right angle.

Hand tools

One of the most popular tools that are used for cutting bricks at home is the chisel.

It is advisable to use the chisel if you need to cut one or a small number of bricks.

To work with large volumes, it is better to use productive power tools.

Cutting the chisel is performed in a strict sequence.

There should be no cracks, chips, downed corners and other visible defects on their surface.

Using a chalk or trigger trigger, apply a marking on a brick, according to which we will carry out an incision.

The working part of the chisel (sharp end) put exactly on the drawn fishing line for the trimmer.

We take a hammer and begin to carefully tap on the chisel until the brick breaks.

As a result, we got two parts with rough surfaces.

To make them smooth, you should rub the elements about each other.

Kirpiche Kirpich is carried out using a special chisel for masonry.

They are stronger and more reliable than ordinary models.

Such products are made of high.quality alloy (chromomolibden or chromovanadium steel), resistant to increased mechanical loads, wear, have a long service life.

Choosing a chisel with which you will cut a brick, do not save.

A good tool will last for many years, maintaining functionality, and low-quality will come into unsuitability after 5-6 use.

Corner grinder

Corner grinder is a universal instrument that is definitely in the garage or utility of each household man.

If we are talking about cutting bricks, then the scope of this apparatus includes low.rise construction, small.scale production.

Simply put, if the acquisition of a special machine does not justify itself, it is advisable to use an angular grinder for cutting bricks.

To cut the material using this power tool, prepare:

Diamond and abrasive discs are used to work with bricks.

They differ between themselves, the scope of use, cost.

The abrasive disk costs cheap, grows very quickly, you can only cut it deeply as a whole.

Diamonds provide high efficiency and safety, have a longer service life.

Related Posts

| Denial of responsibility | Contacts |RSS