How to correctly assemble blades on a cultivator

Types of tillers for a power tiller

If you choose the right power tiller, you don’t need to buy a plough. The cultivator is very easy to operate during milling, there is no great strain on the operator. Cultivator cutters are selected depending on the power of the machine and the type of soil to be plowed.

There are three main types of tillers:

  • Factory-made. Most machines are equipped with them. They come in assembled and disassembled types. Axle with welded plates and attached saber-shaped blades. Two or three identical sections are connected by bolts. Their number affects the width of cultivation. Factory tillers will cope with the pre-tilled areas;

Often, a factory-made tiller is not enough. To increase yields, reduce the load on your equipment, and save time, it’s worth buying “Goose legs”. For heavy development of the virgin soil more suitable soil tillers “Tselina”.

Making a reversible plow for a power tiller with our own hands

Earlier we considered the possibility of using a plow (homemade) instead of a tiller as attachment equipment for a power tiller. Both the miller and the plow perform similar functions, but differ in quality of workmanship. The same difference between a reversible plough and a standard one.

Such a plow has a more complicated design, in which the body on top is equipped with a bent feather. Due to this structure, the reversible plow not only plows the ground, but also reverses the layer of land that has been plowed. This may be useful when working with heavy soil. The arrangement of a reversible plow is much more complicated than that of a conventional plow, and only a professional can make a reversible plow themselves. It is very difficult to choose the right blanks and not to make a mistake in the process.

In order to assemble such a plow yourself, you need to know what to assemble it from, that is, what parts should be made first.

See also  Hydraulic elevator for cars with their own hands

To make a plow Zykov his own hands, you need to make a rack, which will chain the plow to the motor block, plow body with ploughshare, field board (it makes the plow more stable) and a feather, which overturns the earth. This plough’s mouldboard is made of a pipe half a meter in diameter with 5 mm thick walls. We turn on the welder to cut the moldboard, which we then grind with an angle grinder. For the body birch steel plate thickness of 2-3 mm.

What they say on the forums?

On the Internet there are a large number of forums where people share their experiences, how to cultivate with a power tiller Neva.

“Cultivation for me, as a farmer, is an integral part of working with the land. It is a necessary procedure that allows you to increase the amount of crops. With power tillers I’m on a first-name basis, as without it I can not imagine my work now. Thanks to him, the process is fast and good. Yes, it is necessary to make physical efforts to control the power tiller, but not without it in agriculture.”

“I set up the tillers, and was happy to go to my plot. But the work initially seemed to be very hard. Cultivation was slow, uncomfortable and with a lot of effort. I was at a loss as to why this was so. I thought for a long time and wondered what I had done wrong. It turned out that it was just necessary to lower the control knob lower. I repositioned it, and the work went much easier.”

The plow with my own hands

Self-made plow for power tiller is a reality. Only in this case it is important to find accurate and correct drawings. This will have an effect on the tillage quality.

The plow blade itself is usually made of 3 mm thick steel. It is important to bend it correctly. A normal metal pipe template helps to do it correctly.

For the stand you take a metal plate with a thickness of at least 10 mm. The depth is adjusted by the location of the stand on the bracket. The angle of ploughing is determined by the inclination of the tiller. An adjusting screw can be used for this purpose.

The ploughshare cuts the soil and forms its layer. Traditional version. two-sided design. But you can also choose a more modern version of a self-sharpening ploughshare. In the first case, it is necessary to periodically sharpen the equipment. This will allow you to loosen the soil evenly, cut the roots of weeds.

See also  Einhell ce bc 4 m review

Cultivator Blades Shovels phalas manufacturers gobindgarh punjab india

Do the cutters on the single axle tractor need to be resharpened??

There is no definite answer to this question. It all depends on the individual characteristics of the power tiller, soil and conditions of use. For example, sharpening is not necessary for heavy soils with a power tiller with reinforced tillers. You will not see any good effects from this procedure. it is only a waste of time and effort.

For working on a lighter area with a smaller tiller, sharpening is a good option to improve the quality of work. But there is a disadvantage here too. Firstly, sharpening is enough only for a few hours, then the procedure must be repeated, and it is a long and laborious process. Secondly, sharpened knives contribute to the crushing of the roots of weeds, and this in turn can only accelerate their reproduction.

If you do decide to sharpen the tiller, remove it from the power tiller, clean it from the ground. Resharpen each cutting element with emery paper very carefully so as not to damage them.

Cutters (cultivators) for power tillers and power tillers

Cutters for power tillers. attachments designed for plowing, loosening the soil, mixing it with mineral and organic fertilizers, weed and pest control.

Due to their high agronomic characteristics and high degree of crumbling, tillers create an optimal soil density, increase its biological and biochemical activity, while significantly increasing yields. Tillage is carried out in spring before planting and after the fall harvesting of coarse-stemmed crops.

The devices are installed on tillers and power tillers as a working tool. They can be supplied in a basic package when purchasing mototekhnika, sold separately in local markets, and some craftsmen make them on their own.

Cutters for a cultivator (motocultivator): how to make their own hands

Tines for power tillers are easy enough to construct and do not require large financial outlays. As a rule, they are already present in the set of agricultural machinery, but not always this attribute has a suitable width for processing. Made with your own hands equipment. a great way to get the right-sized equipment. Let’s study the types of cutters, the peculiarities of their self-made and installation on the cultivator.

correctly, assemble, blades, cultivator

Homemade tillers for the motor-block

Manufacturers offer different versions of tillers for power tillers. You can use one set of tillers or buy two different types of devices, changing them depending on the conditions of tillage.

See also  Cultivator elitech kb 60 what belt

Some craftsmen prefer to use homemade products, which, if assembled correctly, will be no worse than the factory ones.

The main advantage of making a soil cutter yourself is that it can be adjusted to the specific features of the site.

Sharpening a self-made tiller

The tillers made by your own hands need to be sharpened. You will need an angle grinder with a diamond wheel, which has a diameter of 125 millimeters. The sharpening machine is difficult to use because of the size and bending direction of the blades. Small knives can be sharpened with fine sandpaper.

Rules for sharpening knives on homemade equipment:

correctly, assemble, blades, cultivator
  • Knives may only be sharpened at a 45° angle. The side of the burrow is determined beforehand;
  • It is not necessary to remove a lot of metal; 1-2 sharpenings per season is enough. Frequency of sharpening may vary, depending on the amount of use and the type of soil to be cultivated.

If the unit is often operated on wet ground, the condition of the tines must be checked. Corrosion can be prevented by using a special anti-corrosion agent. Avoid contact with stones and other hard obstacles. This extends the life of the equipment and reduces the need for frequent knife sharpening. When the work is finished, the tillers should be cleaned of soil, plants and other contaminants. Use a rag or brush, various cleaners are not suitable. If the cutters will be stored for a long time, the knives are lubricated with solidol, and for the ends of the shaft use graphite grease.

Homemade cutters can be installed on cultivators Mole, Kentavr and many others.

Related Posts

| Denial of responsibility | Contacts |RSS