How to Calculate Grass Trimmer Oil

Gasoline to oil ratio for grass trimmer table. The first run-in of a lawn mower

Hello! I bought a Prorab 8406 1 grass trimmer. How to dilute gasoline with oil correctly and in what proportion? Could not find original Prorab oil, bought Hungsvarna HP oil. The trimmer manual says that third-party oils can be used SAE MIF\4, API TC-TB. You don’t change the fuel mix ratio if you use a different brand of oil. Standard mix ratio is 1:25. But in the specialized store “specialist” who sold me the oil Hungsvarna HP strongly advised to dilute it 1:50 (as written on the oil). The actual question: if the instruction manual says dilute oil to 1:25, but the oil is recommended 1:50, then in what proportion dilute? And how much is 1:25?? 40 ml? I won’t blow up my engine if I use 1:50? 2. What is the right way to run-in the engine?? The manual does not say anything except to start and shut it off. Maybe it is not necessary to run in? I read that there are grass trimmers that you can work with immediately after purchase.

Correct Way To Mix Gas and Oil For a ChainSaw, WeedEater etc.

Is it necessary to lubricate the gearbox before use, or is there factory-set grease already in place?? Hope for your help, thanks!

1) Petrol and oil are ALWAYS diluted in the proportions indicated on the oil can! With two-stroke products (gasoline-powered trimmers, chain saws, etc.) it is not allowed to use half gases.) you can use any oil for two-stroke engines, except for boat two-stroke engines. It is preferable to use oil from a legitimate store where you are unlikely to buy fake oil. Better to use Husqvarna or STIHL oil. STIHL oil should have a sealed neck. Beware of counterfeit fuel. You risk ruining a piston right away. 2) No running-in of two-stroke products! PLEASE REMEMBER THIS! All 2-stroke products are high-speed and like to run exclusively on full throttle! No half gases are allowed! This leads to incomplete exhaust and deposits oil on the piston rod walls. Piston scuffing as a consequence. So full throttle and every 25-30 seconds you do a 1-2 second throttle reset to give the product a break and return to normal temperature. 3) The gearbox of a straight-shaft brushcutter requires new grease every 20 hours. The oil comes out of there naturally during operation. This is done so that dirt, dust, etc. can escape with the grease. д. So, if you don’t want to get into gearbox replacement, fill it with a special gearbox grease every 20 hours. It’s not hard and the whole operation takes no more than 3 minutes. You can buy tubes of grease in every garden supply store, and the price ranges from 100 to 300. 1 tube lasts 3 years- The notion of running-in tool is reduced to working with incomplete load during the first two or three tanks of fuel. For example, when mowing thin, low grass or sawing dry, undersized wood. In no case you should not run the tool in idle mode burning several tanks of fuel. Such running-in results in carbon fouling on the cylinder windows, piston, and muffler, negatively affecting engine life.

Grass trimmer, or lawnmower. a tool that is indispensable in the household. But its reliability, efficiency and long life depends on many factors.

For example, the quality of fuel. This means that you need to choose the right oil for the grass trimmer, observe the proportions when adding it to gasoline, and follow the rules for filling the device.

Fuel mixture for two-stroke engines

Grass trimmers, which are equipped with a two-stroke motor, do not have a separate system designed for oil supply in order to lubricate the rubbing parts. For this reason, it is not necessary to fill such devices with pure gasoline, but with a mixture of fuel and engine oil. The engine oil should be specially formulated for two-stroke engines. The use of automotive engine fluid will lead to premature engine failure.

Preparation of fuel mixture for twin-roller engines

Fuel your two-stroke lawnmower with AI-92 gasoline. Using AI-95 can lead to engine overheating and uneven machine performance. Gasoline and oil should be mixed in the proportion 50:1, where 50 is fuel and 1 is oil. It turns out that you need 20 ml of oil per 1 liter of fuel.

If the engine is worn or the tool is operated with a high load, the proportion 25:1. If there is not enough lubricant there will be scoring on the cylinder walls and piston surface. The piston ring will then be destroyed and the engine will seize up. Too much is not so critical, but it can lead to carbon deposits. The piston ring will then get corked, which will reduce the power of the device.

Correct Way To Mix Gas and Oil For a ChainSaw, WeedEater String trimmer. Easy 2 Cycle Oil Gas Mix!

Proportions of oil and petrol for the fuel mixture

Gasoline for blending

The requirements for blending gasoline are extremely high, because.к. it is the basis of it. The first thing you should not do, this is to look for places where you can buy fuel cheaper (filling station without a name, etc.).д.), because all the apparent savings of several tens may be eaten up by a costly engine repair, put out of action by low-quality fuel.

See also  How to choose a battery-powered hedge trimmer

Using cheap gasoline with a lower octane rating puts more strain on the machine. Its wear and tear is much faster, its service life is reduced, and not by one to one, but much more

calculate, grass, trimmer

The second thing to remember is that it’s important to use only fresh gasoline for the base of the mixture. Many people have fuel stocks at their dachas or in their garages, standing there for up to six months, waiting in the wings. Fuel, when evaporating, reacts chemically with the surface of the canister (especially plastic), thereby acquiring new properties, not useful for the internal combustion engine. If the gasoline has stood in a canister for a month and a half, it is better to pour it into the fuel tank, where, mixed with the total volume of fresher gasoline, it will not cause any harm to the car engine. The two-stroke engines are more sensitive in this respect. That’s why manufacturers recommend using only the highest quality fuel.

As for the octane number, there are still debates among experts about what gasoline pour into the trimmer for the grass. Most of the producers recommend to fill up the fuel system only with high-octane gasoline of the 92nd brand. There is one little caveat, though: quite often the instructions specify “not lower than 92nd”, which leaves room for guesses as to what kind of gasoline to use.

Of course, the performance (efficiency) of the 95th gasoline is somewhat higher than that of the 92nd. The latter, in turn, is the successor of Soviet 80, which was used to run many machines. But having a higher energy efficiency, the 95th has some peculiarities. For example, it is more suitable for modern models of cars, while the internal combustion engines installed in garden equipment are far from any design innovations, their structure remains practically unchanged for decades. For the two-stroke gasoline engine installed in the majority of modern trimmers, it will be sufficient to fill the tank with 92-grade gasoline bought in a proven gasoline network.

It is best to look for unadded versions marked “eco”, “ecto”, etc.к. You need a clean gasoline base to work clearly. The oil will provide additives for the mixture.

Whether you need 95 gasoline for optimal performance is more of a philosophical question, and there is no specific answer. It is enough to remember that in the tolerances and recommendations, it occurs rarely enough, and this already says a lot. In addition, it is usually filled at your own risk, wishing to improve performance. If you wish to switch from 92 gasoline to 95 for the sake of experiment, it is important to remember the consequences in the form of increased wear, unstable operation of the power unit and failure of its individual components. Of course, none of the above may happen, but the likelihood, if out of tolerance, is extremely high.

Learning how to dilute gasoline with oil for grass trimmer if you under or overfill the oil

If you have bought a grass trimmer, lawnmower, brush cutter, chainsaw and other types of equipment, you probably know that two-stroke motors are used as power units on them. These motors don’t run on pure gasoline, like four-stroke motors, but on a mixture of gasoline and oil. In what proportion should gasoline be diluted with oil for grass trimmer. this is the question every dacha owner asks himself before preparing a tool for work. Let’s understand this question in detail, as the dilution of gasoline with oil for trimmer for grass affects the service life of the tool, and improper preparation of the mixture, will lead to rapid engine wear. What is the danger of too much or not enough oil in the gasoline for the grass trimmer:

  • If the gasoline is diluted with a lot of oil (more than normal) it not only produces a lot of smoke, but also burns the cylinder walls and reduces the power output. This soot will cause piston wear, which will be diagnosed by a decrease in its performance
  • If gasoline contains an insufficient amount of oil poured into the trimmer for grass, it is even more dangerous. After all, the working mechanisms of the engine will not be lubricated in sufficient quantity, which will eventually lead to their rapid deterioration (there is a rapid destruction of piston rings and seizure of the motor). If there is not enough oil in the gasoline poured into the grass trimmer, the wear of the motor will occur dozens of times faster

In order not to pay for mistakes with the price of an engine overhaul or buying a new tool, you must fill the tank with fuel of the correct consistency from the first day. You can find out the ratio in the instruction manual of the tool, because the models of different manufacturers may give different recommendations. This ratio is usually as follows:

  • 1 to 25 or 40 grams of 2-stroke oil for 1 liter of petrol
  • 1 to 40 or 25 to 30 grams of grease per liter of gasoline
  • 1 to 50. this is 20 grams of oil added to a liter of gasoline

The standard value is 1:50 (it is written on canisters with oil for two-stroke engines), but you have to rely on it as a last resort, because the manufacturers indicate the recommended proportion value, and if you do not observe it, the exploitation resource of the two-stroke engine will decrease.

In addition to observing the proportion, you must also learn how to prepare the mixture. After all, the option of adding oil to the gas tank, is categorically contraindicated, although some do so. If you have bought a grass trimmer or lawnmower, you will need the consumables that you will use to prepare the mixture. Instructions for the preparation of the fuel mixture in the grass trimmer is as follows:

  • Prepare gasoline and two-stroke oil, based on the above recommendations for the choice of lubricant and fuel
  • In addition for the preparation of the mixture you need to take a container or a container. You usually use a plastic bottle and you have to choose the right one. It has to be clean on the inside. Do not use a container from milk, beer or other beverages. The optimal solution is a mineral water tank
  • It is very important that the container has a whole value of volume, that is, 1 or 2 liters, so that you do not have to calculate how much to pour oil in a bottle of 1.5 liters, 1.3 or 1.25 liters because you can easily make a mistake
  • You also need a syringe used as a measuring device for dosing the oil. A standard 10cc or larger medicine syringe is adequate for this purpose. A precision measuring scale on the syringe is desirable
  • After preparing the necessary materials, you can proceed to the preparation
See also  How to properly trim linoleum. Tips from the pros

Instructions for preparing the fuel mixture for the lawnmower:

  • First you should fill the plastic container. Do not fill the container more than 2 fingers full so that the oil can fit in
  • Pour the required amount of two-stroke oil into a syringe, and pour it into a bottle with gasoline. This is the way to do it, not the other way around
  • After adding the lubricant to the bottle, you need to close it tightly with the lid and stir. However, keep in mind that oils marked “pre mix” need to be stirred. If the oil bottle is marked “self mix”, then it is not necessary to shake the container, and after combining the substances, you can pour them into the tank of the tool

After preparing the fuel mixture for the grass trimmer, you only need to fill up the tool, and start working. How to properly fuel grass trimmers, lawn mowers, chainsaws and other types of motor equipment, we will consider in detail.

Gasoline and oil proportions

You need to choose a solution taking into account the recommendations from the manufacturer of the grass trimmer. As a rule, the grass trimmer uses a brand of gasoline AI-92. If the manual says 95, then you have to dilute this one and don’t save too much (don’t take less than 92). Two-stroke motor oil is classified according to API. It is worth paying attention to only two types:

  • TA. for air-cooled engines (suitable for lawnmowers).
  • TB. for small engines up to 200 cm³ (intended for chainsaws and small motorcycles).

Other categories (for snowmobiles, boats, etc.).п.) not used in grass trimmers. When buying the product one should pay attention to the package. The domestic manufacturers have a note concerning mixing with fuel:

The following table of recommended quantities shows how many milliliters of lubricating oil are required for each quantity of engine fuel, taking into account the required proportions:

Gasoline (in liters) Oil (in milliliters, depending on the proportions)
1:20 1:30 1:40 1:50
1 50 33 25 20
1,5 75 50 38 30
2 100 67 50 40
3 150 100 75 60
4 200 133 100 80
5 250 167 125 100
6 300 200 150 120
7 350 233 175 140
8 400 267 200 160
9 450 300 225 180
10 500 333 250 200

Features for filling your brushcutter

In order for the mixture to properly distribute in the fuel system of the device, you need to follow a simple instruction. How to properly fuel a gasoline grass trimmer:

  • Place the brushcutter on a horizontal surface with the tank nozzle at the top and pour in the required amount of mix;
  • Don’t fill the grass trimmer too much. keep an eye on how much fuel is at the top mark level;
  • Do not spill any fuel on the ground or on the tool body;
  • Before starting the engine, ensure a safe distance to the fuel tanks;
  • If you had old fuel in the tank, you must empty it completely before refueling.

Filling up brushcutters with two-stroke engine

To fill petrol trimmers of this type, follow the already described procedure. The oil ratio must be strictly adhered to and no spills should occur on the body of the tool. Always check that the fuel tank is not overfilled, because otherwise the engine will be unstable.

Fueling your brushcutter with a four-stroke engine

The main difference is that the grass trimmers with this type of engine is not filled with oil. It is necessary to fill separately the Ai-92 and engine oil. General rules for filling the tank are similar to those already described above.

calculate, grass, trimmer

What you need to know?

Choosing the right oil ratio is not an easy task. It is necessary to calculate the proportions of mixing in accordance with the established norm. Sometimes drivers add ingredients as they see fit. At the same time, disciplined vehicle owners who are concerned about the engine know that the recommended proportion is 1 to 50. This is how much oil? You will find the answer to this question below.

To mix the ingredients, there are simple rules to follow. To dilute gasoline with oil 1 to 50 it is recommended to use fuel grade A-92. They often use A-80, explaining such action by a large number of additives in its composition. This is fundamentally wrong.

Oil of almost any kind is suitable for mixing with fuel. The main thing is that it should belong to the auto group, and not intended for tractors or motor boats. It is not a good idea to use oil. Otherwise it will obviously shorten the life of the engine.

How much oil per liter of gasoline is needed for a lawn mower or a chainsaw?

All two-stroke engines run on a fuel mixture of gasoline and oil. The fuel enters the cylinder, burns there, creating a working force on the piston, and the part of the mixture that has not had time to ignite lubricates the moving parts of the piston group.

See also  How to use a trimmer for grass correctly. How to mow high grass?

When compiling a fuel mixture for a lawnmower or chainsaw, you need to calculate how much oil you need per liter of gasoline, based not only on the standard proportion, but also on what brand of gasoline and oil is used. In the case of two-stroke motors, this is very important.

For trimmers a special two-stroke oil is produced, on the package of which there should be a note “2T”. You should never use motor oil, much less gear oil. Produced by two-stroke oil in three kinds:

It all depends on what substances make up the base of the oil. Mineral oil is the cheapest and most unreliable. Its use is justified only in household trimmers that work for 30-60 minutes a day with long breaks. Most brushcutter manufacturers at this level specify that TC-W3 grade oil is suitable for the engine. This means you can use mineral, synthetic, and semi-synthetic 2T oils.

For professional trimmers, it is advisable to buy only the oil brands recommended by the manufacturer. Normally they are semi-synthetics and synthetics with special additives.

Manufacturers mark the oil with the letters:

  • ? TA for two-stroke engines up to 50 cubic centimeters;
  • ? TV. for 50- to 200cc engines;
  • ? TC. for motorcycle engines, snowmobile engines, etc.д.

All three types of oil may be used in brushcutters, unless the manual specifies otherwise. How much oil to add to the fuel of grass trimmer depends on the brand of tool and the quality of gasoline. Also there may be letters FA, FB, FC, etc. on the oil package.д. These may show the smoke level. The closer the second letter is to the beginning of the alphabet, the more smoke is emitted. As a rule, high-quality oils have very few. This does not affect your choice of oil.

important are the labels “self mix” and “pre mix”. The first word means that the oil dissolves on its own, and the container with the second mixture must be shaken several times.

calculate, grass, trimmer

If the manufacturer’s instructions do not specify what kind of gasoline to use, you must stop at AI-92. If it is recommended to use AI-95, do not use other brands of gasoline.

Some users believe that if you add more oil to the gasoline for the fuel mixture than necessary, it will benefit. It is not. Unburned oil will not be expelled from the engine with the exhaust, but will settle inside as soot. This plaque threatens the integrity of the piston. If you use a mixture with too much oil regularly, the grass trimmer will smoke heavily and a drop in power is inevitable.

If there is not enough oil, the grass trimmer will overheat, the piston rings will collapse and the piston will jam. If the oil deficiency is minor, the grass trimmer will run 30 to 40% less than its life expectancy. If the lubricant is missing more than 20%, the engine will jam after 20 to 30 minutes of intensive work. Every manual for your trimmer gives you the proportions on how to dilute the fuel mixture. usually it is 1:25. 1:40 or 1:50.

Choosing the right oil for your chain saw

Two-stroke engines are fueled with a mixture of unleaded gasoline and oil labeled 2T. It is necessary to use recommended gasoline AI-92. If you use a brand with a higher octane number, the flashpoint and combustion temperature will be higher, the valves will burn out prematurely. The same applies to oil. The recommended composition is not the most expensive. But you can’t use another brand of oil. The viscosity will change, it will lead to insufficient lubrication of conventional products made without high-precision lapping.

If too much oil is added, incomplete combustion leads to carbon monoxide and excessive exhaust emissions. A rich mixture is bad for the engine. For a four-stroke engine oil is poured separately from gasoline. It washes components, cools, reduces friction. The oil becomes contaminated during operation and must be changed after 50 operating hours. What oil to use in your lawnmower, see the datasheet. The composition should be marked as 4T with a viscosity 10W40.

The best oil for any engine is considered to be the one recommended. However, the world famous oil is Shel Helix Ultra. For 40 years the company has been developing a new technology for producing synthetic oil from natural gas. Pureplus technology has made it possible to obtain an improved composition of base oil. On its basis with addition of necessary additives the leading manufacturers get recommended oils for their equipment.

The choice of oil depends primarily on the manufacturer’s recommendations. For example, only STIHL lawnmower oil is used. The same oil is suitable for the brand Vityaz, because the engines in the brands of the same brand. Specialists say that any manufacturer’s oil for any type of machine is suitable for all brands. But if possible, it is better to use the recommended.

Oil must be stored for one season as needed. Product that has stood for a long time loses its properties. Available on sale in packages from 0.1 to 5 liters.

Investigated the path of the oil recommended for the Husqvarna lawnmower. Company does not have its own production facility, only a bottling plant. Products bought in bulk are poured into small packages, labeled and supplied to the trading network. Possibly exclusive Husqvarna additives were added to the oil at the production stage.

Use of oil according to the instruction manual for the brushcutter is mandatory. Equipment cannot work on pure gasoline.

Related Posts

| Denial of responsibility | Contacts |RSS