How to break through a wall without a perforator. Peculiarities

How to drill a concrete wall without a peorator?

It all depends on what exactly will be installed. If an ordinary outlet, then make a round hole. It is easiest to do it because one operation is needed. I installed a drill with a crown on concrete, drilled and all. Quickly, conveniently, technologically and minimum dust. If you need to make a drowned outlet, you will have to tinker and make a square recess on top of the round. It will look much more aesthetic. And if you need to install a block of several outlets or mount the equipment (USB-rosettes, and t.e), it is easier to cut a rectangular recess in the wall with a corner grinder. Or, for example, if there is no tool. In addition to corner grinders.

Strictly speaking the shape of the hole is not so important. The main thing is that a diameter of 72 millimeters (the size of a glass of a socket) fits into the opening in concrete on a rosette). Excess space can then be covered with gypsum, alabastr, putty or at worst by cement.

There is still a nuance regarding the material of the walls. If this is a tree, drywall then everything is wonderful. You can drill holes of any shape and size. If a slag block, then everything is also good. With concrete or brick will have to tinker. But if the tile does not tolerate vibration and has the ability to split. The most optimal output will be diamond cutting with a crown.

Drilling holes in the wall correctly: general rules and recommendations than drill

In order to correctly drill the wall, you need to take into account the material from which it is made, based on this, it is necessary to choose the tool.

  • When working, keep the tool correctly. For example, the drill in the hands should be directly, and enter the surface in a vertical direction;
  • For convenience, use an additional handle;
  • depending on the surface of the surface, select the necessary.
  • Concrete, stone, brick wall. use a carbide drill, more often a winning;
  • metal. a drill for metal;
  • Tiles, ceramic tiles. special cord for these materials, sometimes you can replace the concrete drill with surfacing;
  • Fine stove, wood-for holes of less than 10–12 mm, a metal drill is suitable, for the larger ones, special cores for wood are used.

Councils of specialists

So that you can correctly drill a concrete wall, you must have the necessary equipment, do all the work carefully and adhere to the following recommendations:

  • Without a peorator, the work can be performed by a shock drill or drilled with an electric screwdriver;
  • Do not buy cheap drills, as they quickly disappear the winning tip, and they fail;
  • Instead of a punrate, you can use a winning tool, one will break crushed stone, and the second, inserted into an ordinary electric drill, drill;
  • To work with concrete, the peorator must have a SDS-Plus cartridge;
  • Consider the placement of the reinforcement to determine where it is, you can use the metal detector, if the reinforcement is exposed, it must be painted to prevent rust;
  • To work with concrete, you can use universal drills with diamond spraying, but you need to insert them only into a conventional drill, or you need to turn off the shock mode.
See also  How to hang an angle grinder on the wall

Drill

The tool is suitable when you need to make several holes. You can use the usual drill. Suburbating the winning drill into the body of the wall, sometimes you need to break the concrete with a punch, which coincides in diameter with a hole. This is necessary when the drill begins to get stuck in the surface, bumping into too dense areas. The process is quite laborious.

For greater efficiency, you can use universal sills that have diamond spraying. They are installed only on a conventional drill or on the tool where the vibration function is disabled.

Read how much revolutions per minute at the drill

Монтаж натяжного потолка. Все этапы Переделка хрущевки. от А до Я.# 33

For a large volume, a shock drill and a core with winning tips are used. They are designed for holes up to 12 mm. The drill is suitable for work with metal, concrete.

What professionals advise?

Concrete structures are strong enough and are poorly lending on drilling. In addition, quite often the drills stumble upon the crushed stone, which is part of the concrete mixture, from which wall and ceiling plates are formed.

The holes in concrete have to be done quite often, especially in the process:

  • finishing work;
  • furniture installations;
  • air conditioning pendants;
  • additional electric branch device;
  • Installation of plumbing.

You can solve the problem of holes in the concrete wall in two ways:

How to drill without dust: options than better

Construction work is always accompanied by dust and garbage, but using some recommendations and tips, it can be significantly reduced:

  • The peorator leaves insignificant dust when working so that it does not fly around the room at the same time use a construction vacuum cleaner. Some tools of the tool have a built.in vacuum cleaner, which facilitates the task;
  • Using a drill, it is best to make either a conductor at the end or heap, or make an envelope under the hole so that the garbage falls into it.

Read how to make skiing on a motor block trolley

During the performance of these works, you must adhere to the developed technologies and safety rules, then you can not only make a hole yourself without involving expensive specialists, but also avoid injuries.

See also  How to choose a quality perforator for the house

Than to drill a carrier wall in a panel house with a penetrator

In most panel houses, the walls are made of concrete to make a hole with a peorator, you need to use the winning.

In addition to them, you can use special crowns. They have attacks on the circle. When using them, you need to turn off the shock function of the penetrator.

Experts use diamond drilling, for this you need powerful equipment and skills.

Through holes up to three cm

For repair, a small set of tools and materials will come in handy:

  • Sharp knife;
  • Sealant or PVA glue;
  • At least what material under the hand to fill the place for holes. It can be mint a paper or a piece of foam remaining from the package of the received home appliances;
  • putty;
  • Sandpaper;
  • Shpaklevka knife.
break, wall, perforator

Штукатурка стен. самое полное видео! Переделка хрущевки от А до Я. #5

Before filling the hole of the drywall of this size, it is necessary to prepare the surface:

break, wall, perforator
  • Peel the edges so that an even inner surface comes out, without crumbling with pieces and pieces of paper;
  • Carefully pass the internal edge of the cleaned hole and the area around a primer at a distance of 5-10 cm;
  • The prepared lumps of paper or polystyrene is lubricated on the sides of glue and the hole is locked by it. It is necessary to watch that the edges of a home.made traffic jam do not protrude above the plane of the wall;
  • After the glue dries, the sealed hole with putty.

Subsequent deeds depend on the type of decorative wall coating: the coloring asks painstaking alignment, since a small flaw is prompted on the painted surface. Therefore, the next layer of putty and thorough smoothing with thinly.dispersed sandpaper can be useful.

Errors when working with a drill

The lack of experience can cause mistakes that result in marriage:

  • The use of Sovers not intended for this material. For example, you can not drill concrete nozzles for wood.
  • Using cheap or low.quality nozzles. Such cords quickly break, get stuck in the surface, can lead to injuries.
  • Start. Not always high speed drills accelerate the process. On the contrary, this can lead to overheating of the nozzle or it will quickly dull.
  • Work without breaks. Drill or drill can break due to overheating.
  • Keep the tool not at right angles to the working surface.
  • Excessively press on the instrument.
  • Use a drill, the working part of which is shorter than the required opening depth.

The working part of the drill is part of the nozzles with grooves. Grooves are needed to remove the resulting dust and pieces of concrete from the hole.

With the help of a crown for sockets

The crown is a piece of pipe with a cutting edge on one side and a flange for winding on the pin (it includes) from the other. The pin, in turn, is fixed in the infantry cartridge. Typically, the diameter of the shank varies from 68 to 80 millimeters. Cutting elements are installed on the edge of the crown. It can be the inserts of winning, diamond spraying or simple teeth with one.sided sharpening. Inside the crown there is a passage to fix the drill. This element is intended for centering the crown relative to the future hole. You can do without it, but the result will be unpredictable.

See also  How much oil to put in the brushcutter

Read how to make a strobore

The for crowns are very moderate, and it is not necessary to buy expensive with diamond spraying, if you just need to transfer the outlets or add new. In addition to the walls, it is very convenient to cut holes in the table (for office equipment) or in the kitchen set (for installing the mixer above the sink). To drill a hole using the above tools, it is tedious to perform the following sequence of actions:

  • First you need to mark the wall where there will be a new outlet.
  • Then we determine the center of the marked circle.
  • Then we send a drill to the center (along with the pedorator) and drill.
  • Then we put the crown on the peorator, not forgetting to screw the drill and continue to drill until the passage of the desired depth is not obtained. As a rule, for sockets, enough when the crown is drowned into a wall by 2/3.

As you can see, nothing complicated, the main thing is not to rush and if possible make a deepening in one movement, smoothly and without jerks.

Formation of the hole for the pipe by building components

In addition to the tool, you need to be able to choose the right nozzle. Typically, for one tool there are several sets of drills and nozzles for different types of work. Even for one action, manufacturers offer several options than it can be implemented.

Drill

A drill for a power tool in the case of working with a full.scale wall should be with a winning tip. The material is characterized by high strength, resistance to abrasion.

Compared to similar drills from other raw materials, winning lasts longer. They are used many times.

Drill for brick work

The standard length of the element is 15 cm, purpose. use in everyday life. There are more models for peorators, the largest ones are called a screw drill.

Make the right hole with such a nozzle is possible if you draw a circle. Then drill along the contour of the hole with a pitch of 1 cm. The core is removed with a chisel and a hammer.

This is a way out, if there is no special drill for the pedorator, there is a spatula. it is easy to remove the central part.

Related Posts

| Denial of responsibility | Contacts |RSS