How to attach a ceiling ledge to drywall

attach, ceiling, ledge, drywall

Some features

The ceiling is also quite often finished with plasterboard. Here, too, the ledge can be fixed without much trouble. The same brackets and fixing tools are used for this.

For ceiling mounts you must also first define the mounting points of the brackets. To do this you use measuring tools. You can use a level and a tape measure.

The decor with their own hands: Accessories and furniture from a rope, rope or jute in the interior (45 photos)

The fastening points must be at an equal distance in relation to the window. They are mounted about 15 cm from it. Sometimes the option of mounting on the ceiling is preferable to mounting on the wall. This is typical of those houses that have low ceilings, where the distance from the ceiling to the window is minimal.

Brackets should be mounted at an equal distance in relation to the window. At the same time, you should make sure that they are at an equal distance from him.

Sometimes it is necessary to put a ledge between two walls. This option is also quite often used. This is especially true in rooms where the distance between the walls is minimal. Here, there simply can not be another option for fixing. With this method of installation it is worth measuring the distance from the corner of the wall first, and then from the ceiling to the window.

Once all measurements are made, the brackets can be attached to the drywall. This is done quite easily. It all depends on the fastener that is used for these purposes.

Once the brackets are installed, you can proceed to install the curtain track together with the curtains. Now you can admire the resulting beauty.

Sometimes the ledge to the drywall is attached not with brackets, but through special corners.

These brackets are not always included with the set, so it is better to order them in advance in specialized organizations. This method of attachment is used only in extreme cases.

Most often, mounting with the help of angles used when installing heavy element. In this case, ordinary brackets may not withstand the load, because we are talking about drywall. In addition, when mounted on the corners the load is distributed evenly on the surface of the drywall. In this case, it is less likely that the angle will simply fall off.

So, let’s get to work

To begin, we need to prepare all the necessary tools. Since we need to fasten the cornice at a height, we will need:

To mount the ledge to drywall is advised to use dowel-butterfly.

  • A sturdy and stable stool or stepladder. Tip: When using a chair, place it with its back to the wall;
  • safety glasses, because getting plaster or concrete crumbs in the eyes is a very unpleasant process, which is also not healthy;
  • peorator;
  • a hacksaw for metal;
  • a small hammer;
  • pliers;
  • Phillips screwdriver;
  • level;
  • tape measure;
  • pencil;
  • inspection angle;
  • special dowels for drywall.

A little information about drywall plugs. Butterfly this dowel, after a screw has been screwed into it, opens and thus securely fixes the fastener. Umbrella dowel, works like an ordinary umbrella. Once it has hit the empty space behind the drywall, it opens like an umbrella and thus increases the load distribution area on the drywall. And dowel self-tapping, does not even require pre-drilling drywall, as it is easily screwed with an ordinary screwdriver into the drywall itself. Tip: if you need to install a curtain rod for heavy curtains, in this case it is better to use anchor bolts. In this case, you need to drill the drywall, then drill a hole in the wall at least 5 cm. And the length of the anchor should be selected taking into account the thickness of the plasterboard, the distance between the wall and the plasterboard and the size of the hole in the wall.

Types of cornices for mounting on drywall

It is possible to install a baguette construction or a curtain rod made of plasterboard. The first option is more common, the second attracts an affordable price, as well as convenience in operation. PVC constructions are environmentally friendly, they are subdivided into 2 types, can be wall and ceiling.

Stringed wall cornices differ from other types of their lightness, the models fit well into the interior of high-tech. The designs are designed for the same light fabrics, on them hang tulle, veil, curtains made of organza. String cornices are in demand and inexpensive, they are placed on the wall, ceiling. The curtain rails have a distinctive name, as they resemble the strings of a guitar. They differ in length, fixed with brackets or small brackets.

See also  Can you cut drywall with an electric jigsaw?

Curtain rails are universal, ie. The rails are universal, i.e. can be fitted to various types of interiors. They have a spring that acts as a rod. The models are mounted on plasterboard surfaces or placed in the inner part of the window. In the process of installation brackets are not used.

Installation options

Choose the method of installation of the construction, taking into account its dimensions, as well as other features. In each case, different details are used.

Method 1. special reinforcement of the base

If the ceiling has not yet been created, you should consider this option. The base is strengthened when there is a constructed frame. In the area of attaching the cornice to the plasterboard reinforce the surface inside, use different elements.

There are 2 ways to strengthen the base of the cornice on a drywall wall. First: fix a 3-4 cm thick wooden bar along the construction. The detail is mounted on the wall or ceiling, it is installed through hangers. The base must be secure and cover the entire length of the window. This will make it easier to attach the ceiling cornice to the wall.

To screw the gypsum plasterboard sheets use self-tapping screws on wood, they are securely fixed. The second option of installation involves strengthening the surface with a metal profile, designed for such sheets.

It is necessary to place additional elements near the line along which the construction runs. During installation use screws for metal. The advantage of the second method is the ease of installation. However, if the drywall sheets are already fixed, it is not possible to reinforce the construction.

Method 2 Use dowel “butterfly”

Gypsum plasterboard sheets are mounted on a ready-made structure, use dowels in the form of butterflies, opening on the underside of the cloth. Details allow different types of cornices to be securely fastened. The “butterfly” withstands a weight of more than 14 kg.

Fasten the cornice by means of such plugs simply. At first it is required to assemble it, then attach it to the surface and adjust. The interior element must be evenly positioned on the wall. After that, you must apply a pencil marking, make holes in the cloth, mark them at the points of attachment. In the course of work, it is important to ensure that the structure does not move.

Choose a mounting step (it should not exceed 60 cm) and start making holes. Drywall is not difficult to handle, the process takes 2-3 minutes. To make the holes even, you should hold the tool vertically. Before installing the ledge on the drywall, install dowels. Take 1 “butterfly”, squeeze the base, then insert it into the hole made and fixed to the stop, nailed with a hammer. Dowel is mounted before installing the construction.

It is better to fasten the ledge to the plasterboard. The second person will hold it, and the first person will screw in parts. Each self-tapping screw should be fixed until it stops. After the installation of the elements is finished, you need to put caps on the holes. For a bulky curtain rod with curtains you need to use metal parts instead of plastic ones, the construction will be more reliable. Metal butterflies are strong, comfortable and provide a secure attachment.

Method 3 use dowel type Driva

This method has 3 variants. The simplest: the use of cone-shaped parts that have a wide thread. Inside such elements there is a cavity for installing screws. The cone-shaped parts are available, the price of 1 pc. does not exceed 10

The second option: the use of dowels made of plastic, such elements have a drill bit, under it do not make holes. The tip simplifies the installation process, there is no need to use a drill or drill.

The last option: the use of metal dowels Driva. They are convenient to use, have their own drill. Such fasteners are often used for the installation of kitchen cabinets.

The cornice is installed as follows. First, it is assembled and evenly placed in the ceiling area, after the marking of future parts for fasteners. All the marks must be the same. When using simple dowels, holes should be made with a 7 mm drill bit. If the parts are used for installation with a drill bit, the dowel is put on the screwdriver and screwed into the place of marking.

It is forbidden to put on the part when the drill is on, the dowel may break and the user may be injured. Screw the self-tapping screws into the holes, put the ledge on and secure it with the same parts. Fix the hardware all the way to the stop. The entire process takes 10-15 minutes.

attach, ceiling, ledge, drywall

How to attach the ledge to the drywall

The choice of fasteners depends on the weight of the construction with window drapery, the gap between the wall and the GKL. Consider the most acceptable options, and you decide on the spot based on your case. It should be taken into account that in the kitchen, for example, you can hang a light curtain rod and only a lambrequin, so the fasteners can be for light constructions. In the living room, you will want to drape the openings with heavy curtains, which suggests the fasteners choose more secure. Considering how to hang the ledge on drywall, you should also take into account the fact that if there are little tomboys in the family, they often hide behind curtains, they can pull them, and the design will simply come off, if the fastening is unreliable. So I will give an approximate load that can withstand one or another fixture.

See also  How to secure a suspended ceiling to plasterboard

“Butterfly”. this type of fastening is more appropriate for lightweight constructions. The principle of operation is simple. in a drilled hole you insert the butterfly in the folded state, together with the screw. Screwdriver or an electric screwdriver to tighten the screw, and the butterfly presses its side elements to the plasterboard, creating a spread. Supports a weight of up to 10.12 kg.

Driva. a hollow rod that looks like a meat grinder screw. Available in nylon or metal. According to the design decision models can be with drill. Screw into the drywall sheet and then insert the screw into the inner hole. On it is good to attach the ledge to the ceiling of plasterboard (rails, for example). Holds up to 25 kg of weight.

Molli. it has a hollow rod design and there is a spacer at the end,

Expanding during installation, behind the sheet, pressed firmly to it. The construction is equipped with fixing spikes that do not allow the rod to rotate. In the center, a screw is screwed in, leading to the disclosure of the spacer. Drill a hole, insert the dowel, fasten with a gun, screwdriver. This is the most reliable attachment, supporting a weight of up to 40-45 kg. When the plasterboard is glued to the base on a special glue without a layer of air, it is advisable to use dowel. nail. There are no complications here, drilled a hole with the required diameter, inserted the dowel, screwed. There are other varieties, but briefly highlighted the most commonly used options. After selecting the appropriate fastener for your situation, we proceed to the question of how to hang the ledge on the drywall.

The correct ways to fix the ceiling ledge

Finally, the repair has come to an end, and you can begin to decorate the rooms. For example, to put furniture, install light fixtures, put the carpet on the floor and, of course, hang curtains. To perform the latter, you need to have an idea of how to mount the ceiling curtain rod, because today there are fewer and fewer models that are mounted on the wall.

DIY: How To DRYWALL A CEILING By Yourself. NO Drywall Jack Required!

If we talk about the advantages of these structures, then we should highlight:

  • They look more harmonious;
  • With their help you make the fastening of the curtain rod to the ceiling;
  • the ideal solution for apartments with a ceiling height of 2.5-2.6 meters;
  • as for curtains, they can withstand a lot of weight, not to mention tulle and curtains;
  • combine inexpensive cost and high quality;
  • in spite of their simple appearance, they can be covered with textiles.

It is clear that in order to securely fasten the ledge to the ceiling, you will need to make its high-quality installation. But do not forget that the tulle and the curtains that will hang on it are of no small importance. After all, fully installed construction should not prevent you from using the window.

Therefore it is recommended to place the curtain track 5 cm above the window, so that the curtains don’t overlap the window sill and the radiator. If you will have several rows of curtains, start measuring from the layer nearest the window. Usually the length of the curtain track includes the length of the window plus 30-40 cm on the sides. You can adjust it according to the width, density, and characteristics of the curtains.

The length of the curtain track should allow opening the window opening with the curtains completely open, and if you have heavy curtains, take the construction with greater length. If you have two windows side by side, the length of the curtain track should overlap their total length by 30 cm on the sides. The number of tracks in the curtain track should correspond to the number of layers of fabric. For example, if you plan to hang tulle, curtains and lambrequins, use a three-row ceiling ledge.

In order to make sure the windows open easily, mount the ledge 10 or 15 centimeters away from the wall.

As a rule, tracks for the ceiling are made of PVC. This is a hollow construction, which has several lines. Despite the fact that the ceiling tracks can withstand a lot of weight, you should not make an experiment by hanging on them too heavy curtains.

As for the ways of fixing the eaves, it is used:

Fixing the ledge to the ceiling with their own hands

Installation of the ceiling rail can be done in three ways:

The choice depends on the type of ceiling. The easiest way to mount the rail for curtains with your own hands on a concrete slab or wooden floor. If this is a plasterboard or tensioned design, you must install support beams, which will be attached to the eaves, for hidden suspension device is a special niche.

Fixing the ledge to the ceiling

Making a marking for mounting on the rail itself. From the edges indent 2-3 centimeters, along the entire length at a distance of 20-50 cm. If the busbar is wide, multi-row, it is better to make 2 rows of holes, which should be staggered. Follow the rule: the heavier the curtains, the less distance between the fasteners. Use the drill to make the holes according to the marks. For the front part, choose a drill bit with a larger diameter to deepen the head of the self-drilling screw into the rail. Drill on the inside with a thinner nozzle.

  • Fix the rail exactly along the line and mark the holes on the ceiling.
  • Drill the marks according to the markings. Clean the workplace from dust.
  • We insert the plastic plugs, hammering them flush with the plane of the overlap to ensure the tightest fit.
  • Install the assembled tire in place, fasten the self-drilling screw in the middle, and then fasten from the center to the edges. Make sure the edge of the window goes exactly along the line you drew earlier, that way you will not create any misalignment.
  • On the installed bar, put a decorative bar, if it is provided by the model, insert the hooks, you can hang curtains.
See also  How fast can a single axle tractor go?

How to make a correct attachment to the dowels

Lightweight curtain rod, plastic or string, can be screwed without embedding to the ceiling of plasterboard. Use butterfly dowels instead of normal dowels. It is better to choose curtains that are not heavy: tulle, organza, thin and light synthetic material, cotton, etc.

How to properly install the cornice on the suspended and plasterboard ceilings

The decision about what kind of curtain rod will be installed, should be made even before the repair of the ceiling. The mounting of the ceiling bar to the plasterboard or tensioning system requires the embedding. Usually, this is a wooden bar, a width of 40.Instead of using ordinary dowels, you should use dowel nails and dowel pins 5050, 40-6060 mm, which should be fastened to the ceiling. If the ceiling is planned to lower even lower, then under the beam make pads. It is important that the lower plane of the embedded bar tightly adjoined to the drywall or stretch structure. For very wide eaves, it is recommended to fix two beams side by side.

The center of the mortgage must be exactly in the center of the width of the curtain track, take this rule into account when calculating the distance from the mortgage to the junction of the wall to the window / ceiling, do not forget about the width of the window sill, so the curtains will not stick out on this area.

The cribbing beam provides a rigid and secure base for mounting the rail. Next, the ceiling is mounted, then proceed as described above: how to mount the ceiling cornice to the ceiling. Instead of dowels in this case, you can use ordinary self-tapping screws. To the tensioning system, the ledge is drawn through special polymer rings-gaskets that allow you to minimize damage to the canvas.

A diagram of how to install the embedding beam correctly

Installing the ceiling ledge in the niche

The niche is arranged to install a hidden cornice, such a method is used for stretch and suspended ceilings. Here it is important to competently calculate the width of the niche:

  • If the window sill is standard and protrudes from the slopes not more than 50 mm, then the width of the niche is considered ergonomic 150 mm. this distance is sufficient for convenient work with the rail;
  • If the window sill is wide, then the size of the ledge from the slope should be added to the width of the ledge and another 50 mm.

We measure from the junction of the wall with the window/ceiling the resulting size, outline line, which will be the boundary between the hinged system and the niche. Fasten the bar or metal profile, the edge of the ceiling will approach it. The niche is formed, you can fasten the ceiling cornice to the ceiling according to the algorithm above.

How to hang the ledge on drywall

The choice of fixing method depends on the specific situation.

First prepare all materials and tools.

There are three variants: embedded battens are installed in the framework for gypsum plasterboard, the sheets are installed on a bearing wall, and the ledge must be installed directly on the gypsum plasterboard.

If you can’t fasten the ledge yourself, call a professional.

Fasten with glue

This method can be used if you want to attach decorative curtain rails. In this case, the procedure consists of the following steps:

  • Cutting the rung to the size of the room. For precise trimming, it is better to use a plane or a prepared template made of cardboard.
  • Finishing of gypsum plasterboard with ceiling primer. It will promote a better adhesion to the glue.
  • Applying adhesive mass to the product and fixing it to the ceiling or wall.
attach, ceiling, ledge, drywall

After the glue dries, the process is over, and you can be sure that the construction is holding up securely.

Related Posts

| Denial of responsibility | Contacts |RSS