Extension axle for power tiller with his hands

axle, power, tiller, hands

Adapter for power tiller with his hands, sizes and drawings

Almost all owners of homestead plots need specialized equipment for their work. For a plot of land to constantly carry out care: loosen, plow, dip seedbeds. If you do it all by hand, you will have to spend a lot of time and effort. Not everyone can cope with it, especially older people. That is why power tillers were created, with the help of which it is quite easy to till the ground. But there is one nuance. the adapter, which is a special attachment equipment and helps to cultivate the land. Such equipment is very expensive, so many people make an adapter to the tiller with their own hands.

How to choose and install wheels for cultivator

Very often in agriculture there are serious problems in the movement of equipment. Wheels for the cultivator allow you to easily deliver this unit to any part of the garden. Today’s market offers a huge choice of wheels. However, it is possible to make them with your own hands, without spending a lot of money.

How to make weights for the undercarriage of the cultivator yourself

Weights play a great role in the functionality of the power tiller. Where there is work on the virgin soil, on slopes, in wet or viscous soil, the undercarriage of the machine can slip, because it lacks its own weight.

Weights have been created to solve this problem. You can make them yourself. This will require:

  • Disc weights (from 5 kg);
  • pancakes from a sports barbell (10 kg each);
  • clutch baskets for cars;
  • hexagonal profile;
  • angle grinder;
  • welding machine;
  • electric drill.

Homemade weights The process takes place in the following sequence. In two small sections of the profile holes are drilled, pancake discs from the bar are attached to them, clutch baskets are welded to the pancakes and then weights are attached. The weights are ready and can be attached to the cultivator.

See also  Grinding the cylinder head with their own hands

Installation of weights solves a number of problems at once and greatly simplifies many tasks for the owner of garden machinery.

Types of wheels

Such a machine as a single-axle tractor is used in a variety of jobs, so the wheels installed on it should also be different. Consider the modifications offered by manufacturers:

Pneumatic

Needed for plowing the soil or plowing beds. For quality work the wheels should have a width of more than twenty centimeters with a diameter of 40 centimeters or more. A pronounced tread is welcome.

Such a unit is more stable, and all defects will be visible on the surface of the tires. As a rule, such parts are complete with the motor blocks Neva.

axle, power, tiller, hands

Traction

Commonly these products are called herringbone, because of the unique pattern on the tread. Their working width is universal. This variant is used for transporting loads, or attaching special equipment.

Traction wheels take your machine through rough terrain and even soft snow. The tires on these wheels are durable and hardwearing.

All-cast

These parts are characterized by higher tire power. They are commonly used on diesel-powered machines, more closely resembling small tractors like the MTZ.

Metal with cleats

These are heavy parts that give the tiller extra power when working. Special tines let the machine move even on very hard and sticky soils. The biggest load is on the supporting wheel, so it is worth paying close attention to its choice.

When choosing a trailer, you need to ensure that the wheels in it have a similar structure. That way, when carrying heavy loads, the pressure on the single-axle tractor and the trailer will be compensated.

How to make a cultivator for a power tiller with your own hands?

You will need the following tools and instruments:

The starting material from which the cultivator is made with your own hands:

  • 15×15 cm square stainless steel plates,
  • rectangular plates 12×4 cm of the same material (for the construction of the power tillers),
  • steel tube,
  • nuts and bolts.
  • Guided by the drawing, it is necessary to drill each square and cutter, and then bolt to connect the square on both sides of the cutters.
  • It is necessary to attach the resulting part to the base. It is better to do it with bolts, as welding does not give the necessary strength for the cultivation of the soil connections.
  • Do the same with all the squares.
  • At the next stage of assembly, when the working part will be complete, it is necessary to make a hole corresponding in diameter to the steel tube.
  • The pipe is cut in half, and to each of the resulting parts is welded on the running gear with cutters.
See also  How to connect the starter on the tiller

The resulting design should be connected by bolts or welding machine with the shaft of the power tiller. After checking the reliability of the connections, you can test the cultivator, made with your own hands.

For more clarity and accuracy of the above instructions it is recommended to watch the video.

Eazy handy power tiller

In the same way you can make a cultivator for a mini-tractor with your own hands, changing the size of parts if necessary. The difference is the hitch, which can be made of stainless steel.

How to make the tines with your own hands for a cultivator?

To prevent the wheels of the cultivator from getting stuck in the wet and ploughed soil, and to avoid tamping it, it is necessary to make the grousers, which help to plow the soil additionally. Increasing the passability of the minitractor or power tiller, they additionally increase the efficiency.

To make gruntzatsepov need a welder, which will also be needed if you need to repair the cultivator with their own hands, as well as need metal corners and wheel rims. The work sequence can be performed in two variants:

  • Metal angle is cut and welded to the rim of the disk in 10 cm pieces. The projections formed will act as teeth of the grouser.
  • The second variant of making homemade grousers is based on rims from a cut gas cylinder, 7-9 cm wide. This is the basis for the wheels of the grousers. Using a welder, corner hooks are sliced and welded to the rims with an edge, 15 centimeters apart. A square plate matching the rim diameter is welded to the center of the rim. The axle is welded to the center of the plate.

Such a primer is applicable not only on a cultivator, but also on a minitractor and power tiller.

Types of weights

For the wheels

The disc weights for the wheels of the power tiller are mounted on the discs, as the name suggests. Are thick metal rings with a hole in the middle. In cases of extreme need, can also be made of concrete.

There are two ways to lock them in place. The simplest option. welded. It is suitable in cases where the equipment is constantly used on heavy soils, and there is no need to take it to town at the end of the season. In this case it is quite possible to install permanently welded weights.

axle, power, tiller, hands

Tandem wheels

Each wheel consists of two elements of the same size and shape. This design allows you to significantly increase the cross-country capability of a power tiller on rough terrain and increase speed on a level road.

See also  Thermal clearance of piston rings on the diesel engine of a power tiller

The slip resistance of a machine with dual wheels is practically eliminated, which is why these elements are often used to move the tiller in snowy terrain.

How to make a differential on a single axle tractor with your own hands?

To avoid unnecessary financial costs, you can make a homemade differential. This process is not complicated, and the availability in the free access drawings and a variety of materials further simplify the task.

The manufacturing process looks like this:

  • Using a lathe the part is milled according to the drawings;
  • A flange is milled and carefully welded to a part of the metal pipe;
  • to manufacture the differential, use only blanks made of quality steel, since this part is subject to high loads.

How to make a differential on a single axle tractor with your own hands?

To avoid unnecessary financial costs, you can make a homemade differential. This process is not complicated, and the availability of free access drawings and a variety of materials further simplify the task.

The manufacturing process looks like this:

  • using a lathe according to the drawings a part is milled;
  • A flange is milled and carefully welded to a part of the metal pipe;
  • Use only high quality steel blanks for making the differential, because this part is subjected to high loads.

Related Posts

| Denial of responsibility | Contacts |RSS