Cultivator with their own hands from a chainsaw with their own hands

Homemade single axle tractor: chooses the power plant

The central issue that must be resolved by all who dared to make such a self-made machine, will concern its propulsion part. It will depend on it, whether the future single-axle tractor will “pull” the loads assigned to it or not.

cultivator, their, hands, chainsaw

In this case there could be several options:

  • old engine from a motorcycle, moped, scooter or even a car, which is not always available at hand in good condition, and the purchase of a new one can pull a huge investment;
  • Motor from professional trimmers;
  • the engine component from the performance chainsaws.

Making your own power tiller from the Ural chainsaw

The order of assembling a power tiller with an engine from the Ural is no different from the instructions given above. Differences may arise due to the peculiarities of the selected drawing, but mostly they are insignificant. After assembly, be sure to test the equipment, doing so with the utmost care. Do not forget to install the weighting agent in the front of the motor block, fixing it securely to the body. If the part is not fixed securely, during operation, the power tiller will begin to vibrate, which will lead to damage to the engine.

It is desirable to assemble the construction under the supervision of an experienced specialist, well versed in technology. Assemble a self-made technique for the first time, without experience in this area, is fraught with unpredictable consequences. In the best case you will simply ruin your saw, and in the worst case. your health will suffer. Remember that safety and care at all stages of the assembly is the key to the stable operation of the device. If possible, buy a normal single-axle tractor, and use a self-made machine in extreme cases.

How to assemble a homemade single-axle tractor from a Druzhba chainsaw

Inveterate gardener and gardener has to dig over large areas, which is very tedious, especially when a person is already retired. In addition, this monotonous work is quite boring for most people. Digging, loosening and weeding will take much less time if you will not wield the simplest tools, and use self-made single axle tractor, with which the case will go more fun!

See also  Which cultivator is better with electric or gasoline?

Two Chainsaw Secrets | Turning a Tree into Perfect Boards

Features of the equipment

The main feature of completing such a homemade snow thrower is the use of an engine from almost any model of chainsaw (see “The snow thrower”). Russian-made chainsaws here).

The snow blower from a chainsaw has other features:

  • As a lead pipe, you can use almost any plastic pipe, the diameter of which will be at least 16 cm.
  • The control handle can be made by yourself, from any metal tube.
  • The width of the bucket will depend on the power of the chainsaw engine. If it is powerful enough, the width of the bucket can be increased.

How to make a cultivator from a “Ural” chainsaw with your own hands?

If the rotary disc cultivator is used infrequently and in small areas, the purchase of the unit is considered quite unreasonable. In addition, you will have to buy additional awnings.

Homemade power tiller from a chainsaw includes the following parts:

The above elements have a chainsaw, you only need to find the frame.

Algorithm of manufacture of the unit:

  • The old chainsaw is unscrewed, the engine, gearbox and gas tank are dismantled;
  • The frame is welded. Metal angles 3232 mm in cross section are needed. The design must be durable, not afraid of constant vibration at work and to withstand additional weights;
  • The motor is attached to the upper transverse brackets;
  • The fuel tank is installed and secured under the motor with special brackets. The lower part must be protected by a metal plate;
  • Supports of the intermediate shaft is fixed to the front post of the frame with longitudinal angles;
  • The control unit is created by a crossbar made of metal, the length of which is 30 centimeters;
  • Also, wheels may be attached to the bottom crossbar of the frame for easy transport of the unit. Wheels from an old car are suitable.
  • After assembly, the cultivator must be tested. The motor is started, you need to make one pass over the beds;
  • The structure is weighted down. The weight is placed on the front of the frame. The weighting agent is secured so that it does not move when the unit vibrates and damage the motor/intermediate shaft.
See also  Gasoline to oil ratio for Husqvarna chain saw

Motocultivator from the Ural chainsaw has little power, so there is no possibility of using large sheds. But it is possible to buy a hitch for the use of a homemade harrow and plow.

Working with such a unit, you need to make frequent breaks, so that it does not overheat and fail.

To create such a self-made unit, it is recommended to use special drawings. These schemes can be drawn independently, if you have some knowledge and understanding of the motor-block, or choose one of the suggested options.

Self-made single-axle tractor from a chainsaw is created in several stages, and it is important to observe all the nuances indicated in the scheme.

  • Making the frame. For this use a thick-walled tube, from which you should create a cube with 32x32mm corners.
  • Installing the motor on the upper frame corners of the frame, which are transverse. You must also attach the fuel tank, using brackets (the tank must be placed below the motor).
  • The frame at the front end is equipped with vertical stands that serve as intermediate shaft supports.
  • Special supports are attached to the longitudinal corners so that the shaft bearings can then be mounted.
  • The front part of the frame is loaded with a metal weight that stabilizes the crab.
  • The handles for steering are made of small metal pipes.
  • The single-axle tractor is equipped with old, small wheels, and can also be made from metal plates.

The result is a good single-axle tractor with the center of gravity just above the wheel surface.

Motor cultivator from a chainsaw with their own hands

Cultivating the soil has always taken a lot of time and effort. Therefore, many people began to turn to such equipment as cultivators. They can easily cope with time-consuming work in the garden. But despite the large variety of such equipment, this equipment is considered expensive and not every villager or dacha owner can afford it. Therefore, many craftsmen approach this problem with creativity, constructing self-made cultivators from a chainsaw with their own hands.

Useful things you can do with a chainsaw: cultivator, moped, and others

What a “dodger” you are!! So jokingly call those who have a great imagination and ability to translate it into reality. Thus it is possible to remake almost any thing (or part of a thing), thus changing its purpose. And also to give a broken mechanism a second life. Almost anything can be remade: from a comb to an airplane. We will consider in detail what you can make from a chainsaw.

See also  How to replace a chain on a chainsaw. The tension of the chain

Working principles and types of cultivators

The working principle of the cultivator is simple: the element that loosens the ground begins to work after the mechanical part of the device is started. Depending on the external size, engine power and performance, cultivators are divided into three types: light, medium and heavy equipment.

  • Light equipment is used in small areas with soft soil (flowerbeds, greenhouses).
  • Medium-heavy model used on clay soils.
  • Heavy equipment refers to the universal equipment. It can be used for any soil.

Cultivators are of different types: disc, rotary, tine and milling. By functionality they can be: manual, electric and petrol-powered, as well as trailed, mounted, to cultivate one or more rows.

When cultivating a plot of land, everyone chooses the right model for himself. Manual cultivators are good because they can be made on their own with minimal financial costs.

Advantages and disadvantages

Each cultivator, regardless of whether it is manual or electric, has its pros and cons.

  • Manual cultivator. It is easy to use and much more compact than a shovel. Does not strain the lower back. It loosens the soil well, does not spread the roots all over the plot. But this technique can not cope with not ploughed land, because it has a low performance. It is best used in small areas such as flowerbeds or greenhouses.
  • Electric cultivator. Lightweight and compact, mains-powered machines. Easy to service. Disadvantage of the machine is the electric cord. It can get in the way during work, and because of its length there is a limitation in the cultivated area. Has low power and shallow working depth. Not designed for attachments.
  • Gasoline cultivator. Has many functions thanks to the attachment. Does not connect to electricity, so it can move around the whole plot. Suitable for treating small areas. Weighs much more than electric equipment. It is hard to maintain and requires fuel to refuel.

Related Posts

| Denial of responsibility | Contacts |RSS